[TRNSYS-users] How to calculate pressure difference(pa)

David BRADLEY d.bradley at tess-inc.com
Tue Jul 5 09:31:08 PDT 2011


Wang,
  It depends on what the pressure difference was during your test! 
Typical test data is reported at a 50 Pa pressure difference but if that 
isn't what you used when you measured the infiltration rate then this 
"typical" value is irrelevant.
David


On 7/5/2011 10:59, 王洋 wrote:
> Dear Mr. Bradley,
>      Thanks for your reply!
>     I only want to compare the actual measurement value with the 
> TRNFlow results. I made an experiment in our test room and got the 
> infiltration rate as 0.4 1/h using the tracer gas, but I didn't know 
> the  pressure difference value between indoor and outdoor at that 
> time. Then I used TRNFlow's TEST DATA to set this infiltration rate 
> 0.4 and test and compare the TRNFlow result with the actual 
> measurement result. As you know, the TEST DATA need the pressure 
> difference value between indoor and outdoor. So I asked you about how 
> many Pas I should set?
>  thanks!
> Br.
> wang
>
> 2011/7/5 David BRADLEY <d.bradley at tess-inc.com 
> <mailto:d.bradley at tess-inc.com>>
>
>     Wang,
>       If you are defining the pressure difference value in the test
>     data option then typically you would have the results of a "blower
>     door" test in which a special door containing a computer
>     controlled fan is installed in the building. The fan is run at
>     different speeds to force a pressure difference between indoors
>     and outdoors. Running the fan at various speeds can give you an
>     estimate of the total leakage area of the building. If you are
>     working with a building design (instead of with an actual
>     building) then you can't really use the "test data" type of
>     opening in TRNFlow. You need to use the more theoretical opening
>     types.
>     Regards,
>      David
>
>
>
>     On 7/4/2011 08:14, 王洋 wrote:
>>     Dear Mr. Bradley,
>>         Thanks for your patient reply!
>>        To the pressure difference between indoors and outdoors:
>>     Do you mean it's difficult to use some measuring devices and
>>     methods to test it? Whether there is no an Maths Equation  to
>>     calculate this value according to known data e.g. building
>>     height, wind spead etc.?
>>        Because I need one pressure difference(pa) value in Test Data
>>     Option of TRNFLOW.
>>       Many thanks!
>>      br.
>>     wang
>>
>>
>>     2011/7/1 王洋 <wanghongyang1767 at gmail.com
>>     <mailto:wanghongyang1767 at gmail.com>>
>>
>>
>>         2011/3/16 David BRADLEY <d.bradley at tess-inc.com
>>         <mailto:d.bradley at tess-inc.com>>
>>
>>             Wang,
>>              Chapter 18 is the one you need; look specifically on
>>             page 18.19 at the mathematical description of the
>>             conduction process through the walls.
>>
>>              As for your question about pressure differences, the
>>             pressure difference between indoors and outdoors varies
>>             with a great many factors (windspeed, direction,
>>             obstructions, building height, the nature of the openings
>>             in the building facades, etc.). In many tests, the flow
>>             through an opening with a 50Pa pressure difference is
>>             given. Whether a 50Pa pressure difference is average or
>>             extreme, however, depends on the building.
>>             Regards,
>>              David
>>
>>
>>
>>             On 3/16/2011 08:25, 王洋 wrote:
>>>
>>>
>>>             Dear Mr. Bradley,
>>>
>>>                  But I cann't find the ASHRAE Handbook of
>>>             Fundamentals about
>>>               the Conduction Transfer Function methodology. My
>>>             ASHRAE Handbook of Fundamentals is 2009 version.
>>>             The chapter 4 Heat transfer and Chapter 6 Mass transfer
>>>             have no informations about transfer function coefficients.
>>>             Please tell me which chapter of the ASHRAE Handbook of
>>>             Fundamentals contains transfer function coefficients etc.?
>>>
>>>             PLUS: In Test Data Option of TRNFLOW : about the
>>>             pressure difference(pa). Please tell me normally what's
>>>             the pressure differnce between outside and inside in
>>>             winter or summer? The trnflow manual and Example
>>>             Rest_com.tpf have no detailed introduction. I tried also
>>>             20 pa or 0 pa etc. Is it OK?
>>>
>>>             Many thanks!
>>>
>>>             Br.
>>>
>>>             wang
>>>
>>>
>>>
>>>
>>>
>>>             >
>>>             >
>>>             >  Wang,
>>>             >   The thermal time constant for a zone in your
>>>             building is not a simple
>>>             > thing to compute. It has to do with the materials in
>>>             the wall, the
>>>             > placement
>>>             > of the mass within the wall, the capacitance of the
>>>             zone, ventilation,
>>>             > infiltration, gains, solar radiation, etc. I would
>>>             think that the easiest
>>>             > way to get an estimate of the zone's thermal time
>>>             constant is to impose a
>>>             > step change in one input on it - step change the
>>>             ambient temperature while
>>>             > holding all other inputs constant for example.
>>>             >
>>>             >   The numbers that you see in the *.inf file are
>>>             transfer function
>>>             > coefficients. You can read in the ASHRAE Handbook of
>>>             Fundamentals about
>>>             > the
>>>             > Conduction Transfer Function methodology.
>>>             > Regards,
>>>             >  David
>>>             >
>>>             >
>>>             >
>>>             > On 11/3/2010 09:29, 王洋 wrote:
>>>             >
>>>             > Dear all,
>>>             >
>>>             > 1. How to calculate or find the thermal time constant
>>>             of zone in TRNSYS
>>>             > software?
>>>             >
>>>             > ---------- WALL TYPE BST_FL_HEAT_W1      ----------
>>>             >
>>>             >        THERMAL CONDUCTANCE, U=    67.80000 kJ/h m2K;
>>>             U-Wert=     4.48235
>>>             > W/m2K
>>>             >               (incl. alpha_i=7.7 W/m^2 K and
>>>             alpha_o=25 W/m^2 K)
>>>             >
>>>             >                         TRANSFERFUNCTION COEFFICIENTS
>>>             >    K            A              B              C      
>>>                    D
>>>             >
>>>             >    0       1.7050117E+02    2.1087019E+01    1.7050117E+02
>>>             > 1.0000000E+00
>>>             >    1      -1.1800059E+02    3.5808933E+01   -1.1800059E+02
>>>             > -1.3683139E-01
>>>             >    2       6.0267372E+00    1.6298573E+00    6.0267372E+00
>>>             > 4.7362566E-05
>>>             >    3      -1.2736107E-03    2.3363784E-04   -1.2736107E-03
>>>             >   SUM      5.8526043E+01    5.8526043E+01    5.8526043E+01
>>>             > 8.6321597E-01
>>>             > What's meaning of A B C D? Are they Wall's
>>>             TRANSFERFUNCTION COEFFICIENTS?
>>>             > And what is the thermal time constant of the whole
>>>             zone? How to calculate
>>>             > or
>>>             > find the thermal time constant of the whole zone in
>>>             TRNSYS software?
>>>             > Need I   calculate by myself the whole zone's
>>>             TRANSFERFUNCTION based on
>>>             > all
>>>             > the walls of the zone or others?
>>>             >
>>>             > 2.  How to calculate or find air volume flow of the
>>>             window opening in
>>>             > TRNFlow software?
>>>             >  The window opening area (m2)is known. Whether it
>>>             needs the wind
>>>             > speed(m/s)
>>>             > or not?
>>>             >
>>>             > Many thanks!
>>>             >
>>>             > Br.
>>>             >
>>>             > wang
>>>             >  2010/11/3 <trnsys-users-request at cae.wisc.edu
>>>             <mailto:trnsys-users-request at cae.wisc.edu>>
>>>             >
>>>             >> Send TRNSYS-users mailing list submissions to
>>>             >> trnsys-users at cae.wisc.edu
>>>             <mailto:trnsys-users at cae.wisc.edu>
>>>             >>
>>>             >> To subscribe or unsubscribe via the World Wide Web, visit
>>>             >>
>>>             https://www-old.cae.wisc.edu/mailman/listinfo/trnsys-users
>>>             >> or, via email, send a message with subject or body
>>>             'help' to
>>>             >> trnsys-users-request at cae.wisc.edu
>>>             <mailto:trnsys-users-request at cae.wisc.edu>
>>>             >>
>>>             >> You can reach the person managing the list at
>>>             >> trnsys-users-owner at cae.wisc.edu
>>>             <mailto:trnsys-users-owner at cae.wisc.edu>
>>>             >>
>>>             >> When replying, please edit your Subject line so it is
>>>             more specific
>>>             >> than "Re: Contents of TRNSYS-users digest..."
>>>             >>
>>>             >> Today's Topics:
>>>             >>
>>>             >>   1. Re: GenOpt optimization: problem for the second
>>>             generation
>>>             >>      after 5 simulations (Thibaut VITTE)
>>>             >>   2. Re: google sketchup+trnsys3d (hotline)
>>>             >>   3. input file (Emiliano Casati - 3ME)
>>>             >>   4. Re: GenOpt optimization: problem for the
>>>             secondgeneration
>>>             >>      after 5 simulations (Timothy McDowell)
>>>             >>
>>>             >>
>>>             >> ---------- 已转发邮件 ----------
>>>             >> From: Thibaut VITTE <thibaut.vitte at h3c-energies.fr
>>>             <mailto:thibaut.vitte at h3c-energies.fr>>
>>>             >> To: trnsys-users at cae.wisc.edu
>>>             <mailto:trnsys-users at cae.wisc.edu>
>>>             >> Date: Wed, 03 Nov 2010 11:27:53 +0100
>>>             >> Subject: Re: [TRNSYS-users] GenOpt optimization:
>>>             problem for the second
>>>             >> generation after 5 simulations
>>>             >> Dear Alexis,
>>>             >>
>>>             >> I've had a similar error when I used Genopt. I've had
>>>             several components
>>>             >> tracked by a "trace" command that made my list file
>>>             enormous (more than
>>>             >> 100Mb) and genopt could'nt handle that amount of data.
>>>             >>
>>>             >> Just my 2cents.
>>>             >>
>>>             >> Thibaut
>>>             >> --
>>>             >>
>>>             >> Le futur maîtrisé
>>>             >>
>>>             >>  Thibaut VITTE
>>>             >>
>>>             >> Docteur - Ingénieur Energies
>>>             >>
>>>             >> Mail : thibaut.vitte at h3c-energies.fr
>>>             <mailto:thibaut.vitte at h3c-energies.fr>
>>>             >>
>>>             >> -----------------------------
>>>             >>
>>>             >> H3C-énergies
>>>             >>
>>>             >> 35, chemin du vieux Chêne - 38240 MEYLAN
>>>             >>
>>>             >> Tél : 04 76 41 88 66 – Fax : 04 76 41 28 94
>>>             >>
>>>             >> www.h3c-energies.fr <http://www.h3c-energies.fr/>
>>>             >>
>>>             >>
>>>             >>
>>>             -----------------------------------------------------------------------------------
>>>             >>
>>>             >> Afin de contribuer au respect de l'environnement,
>>>             merci de n'imprimer ce
>>>             >> message qu'en cas de nécessité.
>>>             >>
>>>             >> In order to respect the environment, please don't
>>>             print this e-mail
>>>             >> unless
>>>             >> you really need to.
>>>             >>
>>>             >>
>>>             >> ---------- 已转发邮件 ----------
>>>             >> From: "hotline" <hotline at transsolar.com
>>>             <mailto:hotline at transsolar.com>>
>>>             >> To: "julia.feste" <julia.feste at whitepavilion.com.cn
>>>             <mailto:julia.feste at whitepavilion.com.cn>>
>>>             >> Date: Wed, 3 Nov 2010 11:37:08 +0100
>>>             >> Subject: Re: [TRNSYS-users] google sketchup+trnsys3d
>>>             >> Hi,
>>>             >>
>>>             >> that's a well known problem that will be fixed in the
>>>             next version.
>>>             >> Hopefully upcoming within the next weeks.
>>>             >>
>>>             >> Regards
>>>             >> Christian
>>>             >>
>>>             >> TRANSSOLAR Software Team
>>>             >> hotline at transsolar.com <mailto:hotline at transsolar.com>
>>>             >>
>>>             >> www.trnsys.de <http://www.trnsys.de/>
>>>             >> Transsolar KlimaEngineering - Technologien für
>>>             energieeffizientes Bauen
>>>             >> und Nutzerkomfort in Gebäuden
>>>             >> Transsolar Energietechnik GmbH, Curiestrasse 2, 70563
>>>             Stuttgart /
>>>             >> Amtsgericht Stuttgart - HRB 23347 / USt-IdNr.:
>>>             99073/00911
>>>             >> Geschäftsführer: Dipl.Ing. Matthias Schuler,
>>>             Dipl.Ing. Thomas Auer,
>>>             >> Dipl.Phys. Stefan Holst, Prof. Volkmar Bleicher
>>>             >>
>>>             >> -----Ursprüngliche Nachricht-----
>>>             >> Von: julia.feste
>>>             [mailto:julia.feste at whitepavilion.com.cn
>>>             <mailto:julia.feste at whitepavilion.com.cn>]
>>>             >> Gesendet: Mittwoch, 3. November 2010 06:46
>>>             >> An: trnsys-users at cae.wisc.edu
>>>             <mailto:trnsys-users at cae.wisc.edu>
>>>             >> Betreff: [TRNSYS-users] google sketchup+trnsys3d
>>>             >>
>>>             >>
>>>             >> Hello everybody,
>>>             >> Thanks for your posts that's always really interesting!
>>>             >> I come up with a problem using Google Sketchup and
>>>             TRNSYS3D: inside a
>>>             >> TRNSYS zone, I draft a square, then I want to pull it
>>>             up at a certain
>>>             >> height, so I write the number then Enter, and this
>>>             error appears:
>>>             >>
>>>             >> <-----Beginning of the error----->
>>>             >> ERROR:
>>>             >> NoMethodError
>>>             >> undefined method `position' for
>>>             >> #<Sketchup::AttributeDictionary:0xfcb4eb8>
>>>             >>
>>>             >> BACKTRACE:
>>>             >> C:/Program Files/Google/Google SketchUp
>>>             >> 8/Plugins/Trnsys3d/sketchup/Sketchup.rb:309:in
>>>             `polygon_loop'
>>>             >> C:/Program Files/Google/Google SketchUp
>>>             >> 8/Plugins/Trnsys3d/sketchup/Sketchup.rb:309:in `each'
>>>             >> C:/Program Files/Google/Google SketchUp
>>>             >> 8/Plugins/Trnsys3d/sketchup/Sketchup.rb:309:in
>>>             `polygon_loop'
>>>             >> C:/Program Files/Google/Google SketchUp
>>>             >> 8/Plugins/Trnsys3d/sketchup/Sketchup.rb:321:in
>>>             `outer_polygon'
>>>             >> C:/Program Files/Google/Google SketchUp
>>>             >> 8/Plugins/Trnsys3d/sketchup/Sketchup.rb:326:in `polygon'
>>>             >> C:/Program Files/Google/Google SketchUp
>>>             >> 8/Plugins/Trnsys3d/lib/interfaces/DrawingUtils.rb:27:in
>>>             >> `detect_base_face'
>>>             >> C:/Program Files/Google/Google SketchUp
>>>             >>
>>>             8/Plugins/Trnsys3d/lib/interfaces/DrawingUtils.rb:20:in
>>>             `each'
>>>             >> C:/Program Files/Google/Google SketchUp
>>>             >> 8/Plugins/Trnsys3d/lib/interfaces/DrawingUtils.rb:20:in
>>>             >> `detect_base_face'
>>>             >> C:/Program Files/Google/Google SketchUp
>>>             >>
>>>             8/Plugins/Trnsys3d/lib/interfaces/BaseSurface.rb:254:in
>>>             `face_polygon'
>>>             >> C:/Program Files/Google/Google SketchUp
>>>             >>
>>>             8/Plugins/Trnsys3d/lib/interfaces/BaseSurface.rb:253:in
>>>             `each'
>>>             >> C:/Program Files/Google/Google SketchUp
>>>             >>
>>>             8/Plugins/Trnsys3d/lib/interfaces/BaseSurface.rb:253:in
>>>             `face_polygon'
>>>             >> C:/Program Files/Google/Google SketchUp
>>>             >> 8/Plugins/Trnsys3d/lib/interfaces/Surface.rb:107:in
>>>             >> `update_input_object'
>>>             >> C:/Program Files/Google/Google SketchUp
>>>             >> 8/Plugins/Trnsys3d/lib/interfaces/BaseSurface.rb:94:in
>>>             >> `update_input_object'
>>>             >> C:/Program Files/Google/Google SketchUp
>>>             >>
>>>             8/Plugins/Trnsys3d/lib/interfaces/DrawingInterface.rb:353:in
>>>             >> `on_change_entity'
>>>             >> C:/Program Files/Google/Google SketchUp
>>>             >>
>>>             8/Plugins/Trnsys3d/lib/observers/FaceObserver.rb:32:in
>>>             `onChangeEntity'
>>>             >> C:/Program Files/Google/Google SketchUp
>>>             >> 8/Plugins/Trnsys3d/lib/AsynchProc.rb:17:in `initialize'
>>>             >>
>>>             >> <-----End of the error----->
>>>             >>
>>>             >> When I pull it up manual, I don't have any problem,
>>>             just when I write
>>>             >> the number.
>>>             >>
>>>             >> Thanks in advance for your help,
>>>             >> Julia.
>>>             >> ________________________________________
>>>             >> From: trnsys-users-request at cae.wisc.edu
>>>             <mailto:trnsys-users-request at cae.wisc.edu>
>>>             >> [trnsys-users-request at cae.wisc.edu
>>>             <mailto:trnsys-users-request at cae.wisc.edu>]
>>>             >> Sent: Wednesday, November 03, 2010 1:04 AM
>>>             >> To: trnsys-users at cae.wisc.edu
>>>             <mailto:trnsys-users at cae.wisc.edu>
>>>             >> Subject: TRNSYS-users Digest, Vol 71, Issue 4
>>>             >>
>>>             >> Send TRNSYS-users mailing list submissions to
>>>             >> trnsys-users at cae.wisc.edu
>>>             <mailto:trnsys-users at cae.wisc.edu>
>>>             >>
>>>             >> To subscribe or unsubscribe via the World Wide Web, visit
>>>             >>
>>>             https://www-old.cae.wisc.edu/mailman/listinfo/trnsys-users
>>>             >> or, via email, send a message with subject or body
>>>             'help' to
>>>             >> trnsys-users-request at cae.wisc.edu
>>>             <mailto:trnsys-users-request at cae.wisc.edu>
>>>             >>
>>>             >> You can reach the person managing the list at
>>>             >> trnsys-users-owner at cae.wisc.edu
>>>             <mailto:trnsys-users-owner at cae.wisc.edu>
>>>             >>
>>>             >> When replying, please edit your Subject line so it is
>>>             more specific than
>>>             >> "Re: Contents of TRNSYS-users digest..."
>>>             >>
>>>             >> _______________________________________________
>>>             >> TRNSYS-users mailing list
>>>             >> TRNSYS-users at cae.wisc.edu
>>>             <mailto:TRNSYS-users at cae.wisc.edu>
>>>             >>
>>>             https://www-old.cae.wisc.edu/mailman/listinfo/trnsys-users
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >> ---------- 已转发邮件 ----------
>>>             >> From: "Emiliano Casati - 3ME"
>>>             <E.I.M.Casati at tudelft.nl <mailto:E.I.M.Casati at tudelft.nl>>
>>>             >> To: <trnsys-users at cae.wisc.edu
>>>             <mailto:trnsys-users at cae.wisc.edu>>
>>>             >> Date: Wed, 3 Nov 2010 13:19:58 +0100
>>>             >> Subject: [TRNSYS-users] input file
>>>             >>
>>>             >> Hi to everybody!
>>>             >>
>>>             >> I don’t understand why, for certain projects, I can’t
>>>             open the input
>>>             >> file,
>>>             >> the message is “the system cannot find the path
>>>             specified”.
>>>             >>
>>>             >> Where should I find the input file?
>>>             >>
>>>             >>
>>>             >>
>>>             >> Thanks a lot
>>>             >>
>>>             >>
>>>             >>
>>>             >> ec
>>>             >>
>>>             >>
>>>             >> ---------- 已转发邮件 ----------
>>>             >> From: "Timothy McDowell" <mcdowell at tess-inc.com
>>>             <mailto:mcdowell at tess-inc.com>>
>>>             >> To: "Thibaut VITTE" <thibaut.vitte at h3c-energies.fr
>>>             <mailto:thibaut.vitte at h3c-energies.fr>>,
>>>             >> trnsys-users at cae.wisc.edu
>>>             <mailto:trnsys-users at cae.wisc.edu>
>>>             >> Date: Wed, 3 Nov 2010 07:23:05 -0500 (CDT)
>>>             >> Subject: Re: [TRNSYS-users] GenOpt optimization:
>>>             problem for the
>>>             >> secondgeneration after 5 simulations
>>>             >> This type of error in GenOpt is usually caused by an
>>>             error in the TRNSYS
>>>             >> simulation.  You need to check the *.lst file for the
>>>             TRNSYS run to see
>>>             >> what the TRNSYS error is.
>>>             >>
>>>             >> Regards,
>>>             >>
>>>             >> Tim
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >> ----------------------------------
>>>             >> Timothy McDowell
>>>             >> Executive Vice President
>>>             >> Thermal Energy System Specialists, LLC
>>>             >> 22 N. Carroll St, Suite 370
>>>             >> Madison, WI 53703
>>>             >> Phone: 608-274-2577
>>>             >> Fax: 608-278-1475
>>>             >>
>>>             >> ----- Original Message -----
>>>             >> From: "Thibaut VITTE" <thibaut.vitte at h3c-energies.fr
>>>             <mailto:thibaut.vitte at h3c-energies.fr>>
>>>             >> Sent: Wed, November 3, 2010 5:27
>>>             >> Subject:Re: [TRNSYS-users] GenOpt optimization:
>>>             problem for the
>>>             >> secondgeneration after 5 simulations
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >>    Dear Alexis,
>>>             >>
>>>             >>    I've had a similar error when I used Genopt. I've
>>>             had several
>>>             >>    components tracked by a "trace" command that made
>>>             my list file
>>>             >>    enormous (more than 100Mb) and genopt could'nt
>>>             handle that amount of
>>>             >>    data.
>>>             >>
>>>             >>    Just my 2cents.
>>>             >>
>>>             >>    Thibaut
>>>             >>    --
>>>             >>
>>>             >>
>>>             >> .bodyclass      @page { size: 8.5in 11in; margin-top:
>>>             0.7874in;
>>>             >> margin-bottom:
>>>             >> 0.7874in; margin-left: 0.7874in; margin-right: 0.7874in }
>>>             >> .bodyclass      table { border-collapse:collapse;
>>>             border-spacing:0;
>>>             >> empty-cells:show }
>>>             >> .bodyclass      td, th { vertical-align:top;
>>>             font-size:12pt;}
>>>             >> .bodyclass      h1, h2, h3, h4, h5, h6 { clear:both }
>>>             >> .bodyclass      ol, ul { margin:0; padding:0;}
>>>             >> .bodyclass      li { list-style: none; margin:0;
>>>             padding:0;}
>>>             >> .bodyclass      li span.odfLiEnd { clear: both;
>>>             line-height:0; width:0;
>>>             >> height:0; margin:0; padding:0; }
>>>             >> .bodyclass      span.footnodeNumber {
>>>             padding-right:1em; }
>>>             >> .bodyclass      * { margin:0; }
>>>             >> .bodyclass      .fr1 { font-size:12pt; text-align:center;
>>>             >> vertical-align:top;
>>>             >> margin-left:0in; margin-right:0in; margin-top:0in;
>>>             margin-bottom:0in;
>>>             >> padding:0in; border-style:none; }
>>>             >> .bodyclass      .P1 { font-size:12pt;
>>>             margin-bottom:0in; margin-top:0in;
>>>             >> font-family:Times New Roman; text-align:center !
>>>             important; }
>>>             >> .bodyclass      .P10 { font-size:7.5pt;
>>>             margin-bottom:0in;
>>>             >> margin-top:0in;
>>>             >> font-family:Tahoma, sans-serif; text-align:justify !
>>>             important;
>>>             >> color:#f79646; }
>>>             >> .bodyclass      .P2 { font-size:9pt;
>>>             margin-bottom:0in; margin-top:0in;
>>>             >> font-family:Tahoma, sans-serif; text-align:center !
>>>             important;
>>>             >> color:#e36c0a; font-style:italic; font-weight:bold; }
>>>             >> .bodyclass      .P3 { font-size:9pt;
>>>             margin-bottom:0in; margin-top:0in;
>>>             >> font-family:Tahoma, sans-serif; text-align:justify !
>>>             important;
>>>             >> color:#e36c0a; font-weight:bold; }
>>>             >> .bodyclass      .P4 { font-size:9pt;
>>>             margin-bottom:0in; margin-top:0in;
>>>             >> font-family:Tahoma, sans-serif; text-align:justify !
>>>             important;
>>>             >> color:#e36c0a; font-weight:bold; }
>>>             >> .bodyclass      .P5 { font-size:7.5pt; margin-bottom:0in;
>>>             >> margin-top:0in;
>>>             >> font-family:Tahoma, sans-serif; color:#e36c0a;
>>>             font-weight:bold; }
>>>             >> .bodyclass      .P6 { font-size:7.5pt; margin-bottom:0in;
>>>             >> margin-top:0in;
>>>             >> font-family:Tahoma, sans-serif; text-align:justify !
>>>             important;
>>>             >> color:#3329b1; }
>>>             >> .bodyclass      .P61 { font-size:8.5pt;
>>>             margin-bottom:0in;
>>>             >> margin-top:0in;
>>>             >> font-family:Tahoma, sans-serif; text-align:justify !
>>>             important;
>>>             >> color:#3329b1; }
>>>             >> .bodyclass      .P7 { font-size:7.5pt; margin-bottom:0in;
>>>             >> margin-top:0in;
>>>             >> font-family:Tahoma, sans-serif; text-align:justify !
>>>             important;
>>>             >> color:#3329b1; font-style:italic; }
>>>             >> .bodyclass      .P8 { font-size:7.5pt; margin-bottom:0in;
>>>             >> margin-top:0in;
>>>             >> font-family:Tahoma, sans-serif; text-align:justify !
>>>             important;
>>>             >> color:#3329b1; font-style:italic; }
>>>             >> .bodyclass      .P9 { font-size:12pt;
>>>             margin-bottom:0in; margin-top:0in;
>>>             >> font-family:Times New Roman; text-align:justify !
>>>             important; }
>>>             >> .bodyclass      .P91 { font-size:12pt; margin-bottom:0in;
>>>             >> margin-top:0.05in;
>>>             >> font-family:Times New Roman; text-align:justify !
>>>             important; }
>>>             >> .bodyclass      .Standard { font-size:12pt;
>>>             font-family:Times New Roman;
>>>             >> }
>>>             >> .bodyclass      .T1 { color:#f79646; }
>>>             >> .bodyclass      .T2 { color:#f79646;
>>>             font-family:Tahoma, sans-serif;
>>>             >> font-size:7.5pt; }
>>>             >> .bodyclass      .T3 { color:#3329b1;
>>>             font-family:Tahoma, sans-serif;
>>>             >> font-size:7.5pt; }
>>>             >> .bodyclass      { }
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >>                  Le futur maîtrisé
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >>              Thibaut VITTE
>>>             >>              Docteur - Ingénieur Energies
>>>             >>              Mail : thibaut.vitte at h3c-energies.fr
>>>             <mailto:thibaut.vitte at h3c-energies.fr>
>>>             >>
>>>             >>              -----------------------------
>>>             >>              H3C-énergies
>>>             >>              35, chemin du vieux Chêne - 38240 MEYLAN
>>>             >>              Tél : 04 76 41 88 66 – Fax : 04 76 41 28
>>>             >>                  94
>>>             >> www.h3c-energies.fr <http://www.h3c-energies.fr/>
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>              -----------------------------------------------------------------------------------
>>>             >>      Afin de contribuer au respect de l'environnement,
>>>             >>        merci de n'imprimer ce message qu'en cas de
>>>             nécessité.
>>>             >>      In order to respect the environment, please don't
>>>             >>        print this e-mail unless you really need to.
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >>
>>>             >> _______________________________________________
>>>             >> TRNSYS-users mailing list
>>>             >> TRNSYS-users at cae.wisc.edu
>>>             <mailto:TRNSYS-users at cae.wisc.edu>
>>>             >>
>>>             https://www-old.cae.wisc.edu/mailman/listinfo/trnsys-users
>>>             >>
>>>             >>
>>>             >> ----- End of original message -----
>>>             >>
>>>             >>
>>>             >>
>>>             >> _______________________________________________
>>>             >> TRNSYS-users mailing list
>>>             >> TRNSYS-users at cae.wisc.edu
>>>             <mailto:TRNSYS-users at cae.wisc.edu>
>>>             >>
>>>             https://www-old.cae.wisc.edu/mailman/listinfo/trnsys-users
>>>             >>
>>>             >>
>>>             >
>>>             > _______________________________________________
>>>             > TRNSYS-users mailing
>>>
>>>             > listTRNSYS-users at cae.wisc.eduhttps://
>>>             <mailto:listTRNSYS-users at cae.wisc.eduhttps://>www-old.cae.wisc.edu/mailman/listinfo/trnsys-users
>>>             <http://www-old.cae.wisc.edu/mailman/listinfo/trnsys-users>
>>>             >
>>>             >
>>>             > --
>>>             > ***************************
>>>             > David BRADLEY
>>>             > Principal
>>>             > Thermal Energy Systems Specialists, LLC
>>>             > 22 North Carroll Street - suite 370
>>>             > Madison, WI  53703 USA
>>>             >
>>>             > P:+1.608.274.2577
>>>             > F:+1.608.278.1475d.bradley at tess-inc.com
>>>             <mailto:F%3A%2B1.608.278.1475d.bradley at tess-inc.com>
>>>             > http://www.tess-inc.comhttp://
>>>             <http://www.tess-inc.comhttp//>www.trnsys.com
>>>             <http://www.trnsys.com/>
>>>             >
>>>
>>>
>>>
>>
>>             -- 
>>             ***************************
>>             David BRADLEY
>>             Principal
>>             Thermal Energy Systems Specialists, LLC
>>             22 North Carroll Street - suite 370
>>             Madison, WI  53703 USA
>>
>>             P:+1.608.274.2577
>>             F:+1.608.278.1475
>>             d.bradley at tess-inc.com <mailto:d.bradley at tess-inc.com>
>>             http://www.tess-inc.com <http://www.tess-inc.com/>
>>             http://www.trnsys.com <http://www.trnsys.com/>
>>
>>
>>
>
>     -- 
>     ***************************
>     David BRADLEY
>     Principal
>     Thermal Energy Systems Specialists, LLC
>     22 North Carroll Street - suite 370
>     Madison, WI  53703 USA
>
>     P:+1.608.274.2577
>     F:+1.608.278.1475
>     d.bradley at tess-inc.com  <mailto:d.bradley at tess-inc.com>
>
>     http://www.tess-inc.com  <http://www.tess-inc.com/>
>     http://www.trnsys.com  <http://www.trnsys.com/>
>
>

-- 
***************************
David BRADLEY
Principal
Thermal Energy Systems Specialists, LLC
22 North Carroll Street - suite 370
Madison, WI  53703 USA

P:+1.608.274.2577
F:+1.608.278.1475
d.bradley at tess-inc.com

http://www.tess-inc.com
http://www.trnsys.com

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.onebuilding.org/pipermail/trnsys-users-onebuilding.org/attachments/20110705/a0bf6a51/attachment-0001.htm>


More information about the TRNSYS-users mailing list