[TRNSYS-users] Type 93_Input Value Recall
David BRADLEY
d.bradley at tess-inc.com
Tue May 27 08:01:33 PDT 2014
Wang,
The number of inputs to Type93 is supposed to adjust automatically to
be equal to the value of parameter 1. Somehow the Type93 in your project
has gotten confused. I would recommend that you change the value of
parameter 1 to three and press "Enter" then switch to the "inputs" tab
and make sure that the proforma is now asking for 3 inputs. Switch back
to the parameters tab and change the value to 1 again and press enter.
Now check the inputs tab to make sure that it is asking for one input.
You could also try deleting the Type93 from your project and then put
in a new one. If even that does not work then there is a chance that the
Type93 proforma itself has been corrupted in which case you would need
to ask your distributor for a new copy of the proforma.
Kind regards,
David
On 5/26/2014 04:37, 王洋 wrote:
>
> Dear all and Mr. Bradley,
>
> I used Type 93 to obtain TSI_S7 (inside surface temperature of
> ceiling) of last time step as the input of my Equation. Therefore, I
> need to store 1 input for 1 timestep (these are the two parameters in
> Type93). My idea is that I get the result of Type56 (TSI_S7
> temperature) and use it as input1 to Type93. Then, I use the output
> from Type93 as the temperature that I use in my equation. However,
> after running, it always exists the ERROR as follows:
>
> *** Fatal Error at time : 0.000000
> Generated by Unit : 44
> Generated by Type : 93
> TRNSYS Message 103 : The TRNSYS TYPE checking routine has found
> an inconsistency in the specified component between the input file and
> the information expected by the Type
> Reported information : An illegal number of INPUTS has been
> specified for this component. Please check the component
> configuration. 1 INPUTS are required and 2 were specified.
>
> Attached is Lst File.
>
> However, There are 2 Inputs for Type 93. One links to TSI_S7 (inside
> surface temperature of ceiling), another isNoname. How should I deal
> with 2nd Input Noname?
>
> How could I deal with this ERROR problem?
>
> Many thanks in advance!
>
> Br.
>
> yang wang
>
>
>
> 2014-05-23 21:01 GMT+02:00 王洋 <wanghongyang1767 at gmail.com
> <mailto:wanghongyang1767 at gmail.com>>:
>
> Dear all and Mr. Bradley,
>
> I used Type 93 to obtain TSI_S7 (inside surface temperature of
> ceiling) of last time step as the input of my Equation. Therefore,
> I need to store 1 input for 1 timestep (these are the two
> parameters in Type93). My idea is that I get the result of Type56
> (TSI_S7 temperature) and use it as input1 to Type93. Then, I use
> the output from Type93 as the temperature that I use in my
> equation. However, after running, it always exists the ERROR as
> follows:
>
> *** Fatal Error at time : 0.000000
> Generated by Unit : 44
> Generated by Type : 93
> TRNSYS Message 103 : The TRNSYS TYPE checking routine has
> found an inconsistency in the specified component between the
> input file and the information expected by the Type
> Reported information : An illegal number of INPUTS has been
> specified for this component. Please check the component
> configuration. 1 INPUTS are required and 2 were specified.
>
> Attached is Lst File.
>
> However, There are 2 Inputs for Type 93. One links to TSI_S7
> (inside surface temperature of ceiling), another isNoname. How
> should I deal with 2nd Input Noname?
>
> How could I deal with this ERROR problem?
>
> Many thanks in advance!
>
> Br.
>
> yang wang
>
>
>
> 2014-05-23 19:00 GMT+02:00 <trnsys-users-request at cae.wisc.edu
> <mailto:trnsys-users-request at cae.wisc.edu>>:
>
> Send TRNSYS-users mailing list submissions to
> trnsys-users at cae.wisc.edu <mailto:trnsys-users at cae.wisc.edu>
>
> To subscribe or unsubscribe via the World Wide Web, visit
> https://mailman.cae.wisc.edu/listinfo/trnsys-users
> or, via email, send a message with subject or body 'help' to
> trnsys-users-request at cae.wisc.edu
> <mailto:trnsys-users-request at cae.wisc.edu>
>
> You can reach the person managing the list at
> trnsys-users-owner at cae.wisc.edu
> <mailto:trnsys-users-owner at cae.wisc.edu>
>
> When replying, please edit your Subject line so it is more
> specific
> than "Re: Contents of TRNSYS-users digest..."
>
> Today's Topics:
>
> 1. Re: problem with type 752e (David BRADLEY)
>
>
> ---------- 已转发邮件 ----------
> From: David BRADLEY <d.bradley at tess-inc.com
> <mailto:d.bradley at tess-inc.com>>
> To: Nidal Abdalla <nidalabdalla at yahoo.com
> <mailto:nidalabdalla at yahoo.com>>, "TRNSYS users mailing list
> at the Solar Energy Lab, UW-Madison"
> <trnsys-users at cae.wisc.edu <mailto:trnsys-users at cae.wisc.edu>>
> Cc:
> Date: Fri, 23 May 2014 11:31:05 -0500
> Subject: Re: [TRNSYS-users] problem with type 752e
> Nidal,
> My apologies for the delay in getting back to you. This is a
> known bug with one of the modes of Type752. The fix is in the
> next scheduled release. If you need the fix immediately,
> please contact your distributor and we can get it to you
> through them.
> Kind regards,
> David
>
>
>
> On 5/18/2014 18:44, Nidal Abdalla wrote:
>> Dear all
>>
>> I am trying use of type 752e to control the humidity ratio
>> with type 56 (in TRNSYS 17). But I couldn't find Absolute
>> Humidity Ratio in the input tab. It is replaced with "Not
>> Used". Moreover an error occur when I run tpf file as:
>> "trnsys message 142 for type 752: a three litter unit code
>> was set for an input number beyond the range reserve for this
>> type". I changed humidity mode to 1, but the problem still
>> found.
>> Any one can help me?
>>
>> regards
>>
>> Nidal
>>
>>
>> _______________________________________________
>> TRNSYS-users mailing list
>> TRNSYS-users at cae.wisc.edu <mailto:TRNSYS-users at cae.wisc.edu>
>> https://mailman.cae.wisc.edu/listinfo/trnsys-users
>
> --
> ***************************
> David BRADLEY
> Principal
> Thermal Energy Systems Specialists, LLC
> 22 North Carroll Street - suite 370
> Madison, WI 53703 USA
>
> P:+1.608.274.2577 <tel:%2B1.608.274.2577>
> F:+1.608.278.1475 <tel:%2B1.608.278.1475>
> d.bradley at tess-inc.com <mailto:d.bradley at tess-inc.com>
>
> http://www.tess-inc.com
> http://www.trnsys.com
>
>
> _______________________________________________
> TRNSYS-users mailing list
> TRNSYS-users at cae.wisc.edu <mailto:TRNSYS-users at cae.wisc.edu>
> https://mailman.cae.wisc.edu/listinfo/trnsys-users
>
>
>
--
***************************
David BRADLEY
Principal
Thermal Energy Systems Specialists, LLC
22 North Carroll Street - suite 370
Madison, WI 53703 USA
P:+1.608.274.2577
F:+1.608.278.1475
d.bradley at tess-inc.com
http://www.tess-inc.com
http://www.trnsys.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.onebuilding.org/pipermail/trnsys-users-onebuilding.org/attachments/20140527/185242a6/attachment-0004.htm>
More information about the TRNSYS-users
mailing list