[TRNSYS-users] Type 93_Input Value Recall

Tue May 27 08:25:40 PDT 2014

Dear Transsolar distributor and David,

Good Day!

I tried to use the two methods as David said last email, but, Type 93 still
has an additional Input Noname and it always has the ERROR after running as
I described last email. Therefore, could you (Transsolar distributor)
forward me a new copy of the proforma for Type 93. My Trnsys version is
16.1.

Many thanks in advance!

Br.

yang wang

2014-05-27 17:01 GMT+02:00 David BRADLEY <d.bradley at tess-inc.com>:

>  Wang,
>   The number of inputs to Type93 is supposed to adjust automatically to be
> equal to the value of parameter 1. Somehow the Type93 in your project has
> gotten confused. I would recommend that you change the value of parameter 1
> to three and press "Enter" then switch to the "inputs" tab and make sure
> that the proforma is now asking for 3 inputs. Switch back to the parameters
> tab and change the value to 1 again and press enter. Now check the inputs
> tab to make sure that it is asking for one input.
>
>   You could also try deleting the Type93 from your project and then put in
> a new one. If even that does not work then there is a chance that the
> Type93 proforma itself has been corrupted in which case you would need to
> ask your distributor for a new copy of the proforma.
> Kind regards,
>  David
>
>
>
> On 5/26/2014 04:37, 王洋 wrote:
>
>
>    Dear all and Mr. Bradley,
>
>  I used Type 93 to obtain TSI_S7 (inside surface temperature of ceiling)
> of last time step as the input of my Equation. Therefore, I need to store 1
> input for 1 timestep (these are the two parameters in Type93). My idea is
> that I get the result of Type56 (TSI_S7 temperature) and use it as input1
> to Type93. Then, I use the output from Type93 as the temperature that I use
> in my equation. However, after running, it always exists the ERROR as
> follows:
>
> *** Fatal Error at time   :         0.000000
>     Generated by Unit     :    44
>     Generated by Type     :    93
>     TRNSYS Message    103 : The TRNSYS TYPE checking routine has found an
> inconsistency in the specified component between the input file and the
> information expected by the Type
>     Reported information  : An illegal number of INPUTS has been specified
> for this component. Please check the component configuration. 1 INPUTS are
> required and 2 were specified.
>
>  Attached is Lst File.
>
>  However, There are 2 Inputs for Type 93. One links to  TSI_S7 (inside
> surface temperature of ceiling), another is Noname. How should I deal
> with 2nd Input Noname?
>
>  How could I deal with this ERROR problem?
>
>  Many thanks in advance!
>
>  Br.
>
> yang wang
>
>
>
> 2014-05-23 21:01 GMT+02:00 王洋 <wanghongyang1767 at gmail.com>:
>
>>    Dear all and Mr. Bradley,
>>
>>  I used Type 93 to obtain TSI_S7 (inside surface temperature of ceiling)
>> of last time step as the input of my Equation. Therefore, I need to store 1
>> input for 1 timestep (these are the two parameters in Type93). My idea is
>> that I get the result of Type56 (TSI_S7 temperature) and use it as input1
>> to Type93. Then, I use the output from Type93 as the temperature that I use
>> in my equation. However, after running, it always exists the ERROR as
>> follows:
>>
>> *** Fatal Error at time   :         0.000000
>>     Generated by Unit     :    44
>>     Generated by Type     :    93
>>     TRNSYS Message    103 : The TRNSYS TYPE checking routine has found an
>> inconsistency in the specified component between the input file and the
>> information expected by the Type
>>     Reported information  : An illegal number of INPUTS has been
>> specified for this component. Please check the component configuration. 1
>> INPUTS are required and 2 were specified.
>>
>>  Attached is Lst File.
>>
>>  However, There are 2 Inputs for Type 93. One links to  TSI_S7 (inside
>> surface temperature of ceiling), another is Noname. How should I deal
>> with 2nd Input Noname?
>>
>>  How could I deal with this ERROR problem?
>>
>>  Many thanks in advance!
>>
>>  Br.
>>
>> yang wang
>>
>>
>>
>> 2014-05-23 19:00 GMT+02:00 <trnsys-users-request at cae.wisc.edu>:
>>
>>> Send TRNSYS-users mailing list submissions to
>>>         trnsys-users at cae.wisc.edu
>>>
>>> To subscribe or unsubscribe via the World Wide Web, visit
>>>         https://mailman.cae.wisc.edu/listinfo/trnsys-users
>>> or, via email, send a message with subject or body 'help' to
>>>         trnsys-users-request at cae.wisc.edu
>>>
>>> You can reach the person managing the list at
>>>         trnsys-users-owner at cae.wisc.edu
>>>
>>> When replying, please edit your Subject line so it is more specific
>>> than "Re: Contents of TRNSYS-users digest..."
>>>
>>> Today's Topics:
>>>
>>>    1. Re: problem with type 752e (David BRADLEY)
>>>
>>>
>>> ---------- 已转发邮件 ----------
>>> From: David BRADLEY <d.bradley at tess-inc.com>
>>> To: Nidal Abdalla <nidalabdalla at yahoo.com>, "TRNSYS users mailing list
>>> at the Solar Energy Lab, UW-Madison" <trnsys-users at cae.wisc.edu>
>>> Cc:
>>> Date: Fri, 23 May 2014 11:31:05 -0500
>>> Subject: Re: [TRNSYS-users] problem with type 752e
>>>  Nidal,
>>>  My apologies for the delay in getting back to you. This is a known bug
>>> with one of the modes of Type752. The fix is in the next scheduled release.
>>> If you need the fix immediately, please contact your distributor and we can
>>> get it to you through them.
>>> Kind regards,
>>>  David
>>>
>>>
>>>
>>> On 5/18/2014 18:44, Nidal Abdalla wrote:
>>>
>>>  Dear all
>>>
>>>  I am trying use of type 752e to control the humidity ratio with type
>>> 56 (in TRNSYS 17). But I couldn't find Absolute Humidity Ratio in the input
>>> tab. It is replaced with "Not Used". Moreover an error occur when I run tpf
>>> file as: "trnsys message 142 for type 752: a three litter unit code was
>>> set for an input number beyond the range reserve for this type". I changed
>>> humidity mode to 1, but the problem still found.
>>> Any one can help me?
>>>
>>>  regards
>>>
>>>  Nidal
>>>
>>>
>>> _______________________________________________
>>> TRNSYS-users mailing listTRNSYS-users at cae.wisc.eduhttps://mailman.cae.wisc.edu/listinfo/trnsys-users
>>>
>>>
>>> --
>>> ***************************
>>> David BRADLEY
>>> Principal
>>> Thermal Energy Systems Specialists, LLC
>>> 22 North Carroll Street - suite 370
>>> Madison, WI  53703 USA
>>>
>>> P:+1.608.274.2577
>>> F:+1.608.278.1475d.bradley at tess-inc.com
>>> http://www.tess-inc.comhttp://www.trnsys.com
>>>
>>>
>>> _______________________________________________
>>> TRNSYS-users mailing list
>>> TRNSYS-users at cae.wisc.edu
>>> https://mailman.cae.wisc.edu/listinfo/trnsys-users
>>>
>>>
>>
>
> --
> ***************************
> David BRADLEY
> Principal
> Thermal Energy Systems Specialists, LLC
> 22 North Carroll Street - suite 370
> Madison, WI  53703 USA
>
> P:+1.608.274.2577
> F:+1.608.278.1475d.bradley at tess-inc.com
> http://www.tess-inc.comhttp://www.trnsys.com
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.onebuilding.org/pipermail/trnsys-users-onebuilding.org/attachments/20140527/26532029/attachment-0004.htm>