[TRNSYS-users] how not to get output list file(*.lst)

佐藤 昭一郎 satos at kajima.com
Tue Jun 24 17:00:46 PDT 2008


David,
  Thanks for your quick response. I attached *.lst file. I'm glad if you could give me some advice.
 Thanks in advance.
Sato

-----Original Message-----
From: David Bradley [mailto:bradley at tess-inc.com] 
Sent: Tuesday, June 24, 2008 11:38 PM
To: 佐藤 昭一郎
Cc: trnsys-users at engr.wisc.edu
Subject: Re: [TRNSYS-users] how not to get output list file(*.lst)

Sato,
  I think that either I misunderstood the use of the NOLIST statement or else it has changed! It seems that using the NOLIST statement will prevent TRNSYS from writing the contents of the input file to the list file but that the warnings, notices, and errors will still always be written. Could you please send me your *.lst file so that I can get an idea of what information is being written there?
Kind regards,
 David


佐藤 昭一郎 wrote:
> Dear David
>
> Thanks for the swift response.
> I used "NOLIST",but I could not suppress the list file.
> Do I misuse "NOLIST"card?
>
> Below is a part of deck file.
> Thanks in advance.
>
> Sato
>
> **********************************************************************
> *********
> *** Units
> **********************************************************************
> *********
>
> **********************************************************************
> *********
> *** Control cards
> **********************************************************************
> *********
> * START, STOP and STEP
> CONSTANTS 3
> START=1
> STOP=24
> STEP=1
> * User defined CONSTANTS
>
> SIMULATION 	 START	 STOP	 STEP	! Start time	End time	Time step
> TOLERANCES 0.001 0.0000001			! Integration	 Convergence
> LIMITS 10000 10000 0				! Max iterations	Max warnings	Trace limit
> DFQ 1					! TRNSYS numerical integration solver method
> WIDTH 80				! TRNSYS output file width, number of characters
> NOLIST 					! NOLIST statement
> MAP 					! MAP statement
> SOLVER 0 1 1				! Solver statement	Minimum relaxation factor	Maximum relaxation factor
> NAN_CHECK 1				! Nan DEBUG statement
> OVERWRITE_CHECK 1			! Overwrite DEBUG statement
> TIME_REPORT 1			! enable time report statement
> EQSOLVER 0				! EQUATION SOLVER statement
>  
>
> -----Original Message-----
> From: David Bradley [mailto:bradley at tess-inc.com]
> Sent: Friday, June 20, 2008 6:58 PM
> To: 佐藤 昭一郎
> Cc: trnsys-users at engr.wisc.edu
> Subject: Re: [TRNSYS-users] how not to get output list file(*.lst)
>
> You can suppress the list file by switching the "LIST CARD" field in the Studio's component control cards from "LIST" to "NOLIST." However, before you suppress the list file, I would recommend that you make a run allowing TRNSYS to write the list file, then look at it and make sure that there aren't a lot of warnings being written there during your simulation.
> Kind regards,
>  David
>
>
> 佐藤 昭一郎 wrote:
>   
>> Dear all
>>
>> I use TRNSYS 16.1.
>> I have trouble about getting output a big size list file(*.lst) Please tell me how not to get output list file(*.lst).
>>
>> Thanks in advance
>> yours
>> _______________________________________________
>> TRNSYS-users mailing list
>> TRNSYS-users at engr.wisc.edu
>> https://www.cae.wisc.edu/mailman/listinfo/trnsys-users
>>
>>
>>
>>   
>>     
>
> --
> **********************************************************************
> * Thermal Energy System Specialists (TESS), LLC
> David BRADLEY                      2916 Marketplace Drive - Suite 104 
> Partner                            Madison, WI 53719 
>                                    USA
> P: +1.608.274.2577
> F: +1.608.278.1475
> E-mail: bradley at tess-inc.com 
> Web Pages:  http://www.tess-inc.com    and      http://www.trnsys.com
>
> **********************************************************************
> *
>
>   

--
***********************************************************************
Thermal Energy System Specialists (TESS), LLC 
David BRADLEY                      2916 Marketplace Drive - Suite 104 
Partner                            Madison, WI 53719 
                                   USA
P: +1.608.274.2577
F: +1.608.278.1475
E-mail: bradley at tess-inc.com 
Web Pages:  http://www.tess-inc.com    and      http://www.trnsys.com

***********************************************************************

-------------- next part --------------
A non-text attachment was scrubbed...
Name: Project1.dck
Type: application/octet-stream
Size: 26846 bytes
Desc: Project1.dck
URL: <http://lists.onebuilding.org/pipermail/trnsys-users-onebuilding.org/attachments/20080625/36d92ddb/attachment-0001.obj>


More information about the TRNSYS-users mailing list