[TRNSYS-users] how not to get output list file(*.lst)
David Bradley
bradley at tess-inc.com
Tue Jun 24 07:37:45 PDT 2008
Sato,
I think that either I misunderstood the use of the NOLIST statement or
else it has changed! It seems that using the NOLIST statement will
prevent TRNSYS from writing the contents of the input file to the list
file but that the warnings, notices, and errors will still always be
written. Could you please send me your *.lst file so that I can get an
idea of what information is being written there?
Kind regards,
David
佐藤 昭一郎 wrote:
> Dear David
>
> Thanks for the swift response.
> I used "NOLIST",but I could not suppress the list file.
> Do I misuse "NOLIST"card?
>
> Below is a part of deck file.
> Thanks in advance.
>
> Sato
>
> *******************************************************************************
> *** Units
> *******************************************************************************
>
> *******************************************************************************
> *** Control cards
> *******************************************************************************
> * START, STOP and STEP
> CONSTANTS 3
> START=1
> STOP=24
> STEP=1
> * User defined CONSTANTS
>
> SIMULATION START STOP STEP ! Start time End time Time step
> TOLERANCES 0.001 0.0000001 ! Integration Convergence
> LIMITS 10000 10000 0 ! Max iterations Max warnings Trace limit
> DFQ 1 ! TRNSYS numerical integration solver method
> WIDTH 80 ! TRNSYS output file width, number of characters
> NOLIST ! NOLIST statement
> MAP ! MAP statement
> SOLVER 0 1 1 ! Solver statement Minimum relaxation factor Maximum relaxation factor
> NAN_CHECK 1 ! Nan DEBUG statement
> OVERWRITE_CHECK 1 ! Overwrite DEBUG statement
> TIME_REPORT 1 ! enable time report statement
> EQSOLVER 0 ! EQUATION SOLVER statement
>
>
> -----Original Message-----
> From: David Bradley [mailto:bradley at tess-inc.com]
> Sent: Friday, June 20, 2008 6:58 PM
> To: 佐藤 昭一郎
> Cc: trnsys-users at engr.wisc.edu
> Subject: Re: [TRNSYS-users] how not to get output list file(*.lst)
>
> You can suppress the list file by switching the "LIST CARD" field in the Studio's component control cards from "LIST" to "NOLIST." However, before you suppress the list file, I would recommend that you make a run allowing TRNSYS to write the list file, then look at it and make sure that there aren't a lot of warnings being written there during your simulation.
> Kind regards,
> David
>
>
> 佐藤 昭一郎 wrote:
>
>> Dear all
>>
>> I use TRNSYS 16.1.
>> I have trouble about getting output a big size list file(*.lst) Please tell me how not to get output list file(*.lst).
>>
>> Thanks in advance
>> yours
>> _______________________________________________
>> TRNSYS-users mailing list
>> TRNSYS-users at engr.wisc.edu
>> https://www.cae.wisc.edu/mailman/listinfo/trnsys-users
>>
>>
>>
>>
>>
>
> --
> ***********************************************************************
> Thermal Energy System Specialists (TESS), LLC
> David BRADLEY 2916 Marketplace Drive - Suite 104
> Partner Madison, WI 53719
> USA
> P: +1.608.274.2577
> F: +1.608.278.1475
> E-mail: bradley at tess-inc.com
> Web Pages: http://www.tess-inc.com and http://www.trnsys.com
>
> ***********************************************************************
>
>
--
***********************************************************************
Thermal Energy System Specialists (TESS), LLC
David BRADLEY 2916 Marketplace Drive - Suite 104
Partner Madison, WI 53719
USA
P: +1.608.274.2577
F: +1.608.278.1475
E-mail: bradley at tess-inc.com
Web Pages: http://www.tess-inc.com and http://www.trnsys.com
***********************************************************************
More information about the TRNSYS-users
mailing list