[TRNSYS-users] AHU Example with heat wheel and VRV system

Chinello Enrico enrico.chinello at epfl.ch
Wed Nov 7 08:25:04 PST 2018


Hello,

I’m trying to model in TRNSYS 17 a system that comprises: solar panels + controller + battery + load. I’m trying to keep the model stand-alone, i.e. without any grid interconnection, but I couldn’t figure out how to set my controller to exclude the grid.
Is that possible? If so, how could I do it?

Thanks in advance for your help,
Best regards,
Enrico Chinello

From: TRNSYS-users <trnsys-users-bounces at lists.onebuilding.org> On Behalf Of David BRADLEY via TRNSYS-users
Sent: mercredi 7 novembre 2018 17:15
To: TRNSYS users mailing list at OneBuilding.org <trnsys-users at lists.onebuilding.org>
Cc: David BRADLEY <d.bradley at tess-inc.com>
Subject: Re: [TRNSYS-users] AHU Example with heat wheel and VRV system


Al-Hyari,

  It is not really possible to know what might be going wrong without running the project. What I would suggest is that you make a new project to which you add only the exhaust and outdoor air fans. Make sure they are the right size by adjusting parameter values and run the simulation using an online plotter to verify that the temperature, humidity and flow rate leaving the fans is as you planned for it to be. Next, add the heat wheel into the system. Again, make sure that the parameters are correctly set so that the heat wheel is appropriately sized to the application. Again, use the online plotter to verify that the temperatures, humidities, and flow rates exiting the wheel make sense. Keep adding one component at a time and verifying as you go.

  kind regards,

 David



On 11/06/2018 05:44, Al-hyari via TRNSYS-users wrote:
Dear Everyone

so i tried by my own to build the model for an AHU Equipped with a heat wheel and auxiliary dx coil connected to a VRV System

i want to know the values of temperature and relative humidity before and after the heat wheel. but there is some mistake that i can not figure it out.

please advise me what can i do to make the correct model to simulate

in the attached files you can find the trnsys model and the schematic diagram for the AHU


Regards







On Tuesday, October 30, 2018, 3:30:38 PM GMT+1, Al-hyari via TRNSYS-users <trnsys-users at lists.onebuilding.org><mailto:trnsys-users at lists.onebuilding.org> wrote:


Dear Colleagues

It is my pleasure to join this discussing group mail.

so my question is :

I am working to simulate an AHU equipped with Heat wheel and an auxiliary dx coil connected to a VRV system.

I am new on TrnSys and i don't have much knowledge.

So if any one could help me by sendeng a similar example to study on it and make modification on the block diagram i would be highly appreciated.

Regards
Laith F. Al-Hyari


_______________________________________________
TRNSYS-users mailing list

TRNSYS-users at lists.onebuilding.org<mailto:TRNSYS-users at lists.onebuilding.org>
http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org




_______________________________________________

TRNSYS-users mailing list

TRNSYS-users at lists.onebuilding.org<mailto:TRNSYS-users at lists.onebuilding.org>

http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org



--

***************************

David BRADLEY

Principal

Thermal Energy Systems Specialists, LLC

3 North Pinckney Street - suite 202

Madison, WI  53703 USA



P:+1.608.274.2577

F:+1.608.278.1475

d.bradley at tess-inc.com<mailto:d.bradley at tess-inc.com>



http://www.tess-inc.com

http://www.trnsys.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.onebuilding.org/pipermail/trnsys-users-onebuilding.org/attachments/20181107/c2eca233/attachment-0001.html>


More information about the TRNSYS-users mailing list