[TRNSYS-users] Component Order

[maverickxxx1991]

17.02.0005 Version 5.4.0.0 

My simulations always hang up. I’ve tried different convergence tolerances. Only 0.003 works, but also not all the times.

> Am 21.02.2018 um 15:34 schrieb hotline via TRNSYS-users <trnsys-users at lists.onebuilding.org>:
> 
> Hey
> You can find the full Trnsys Version in your Simulation Studio under ? - About.
> Could you please provide this number. Thanks!
> 
> -----Ursprüngliche Nachricht-----
> Von: TRNSYS-users [mailto:trnsys-users-bounces at lists.onebuilding.org] Im Auftrag von maverickxxx1991 via TRNSYS-users
> Gesendet: Mittwoch, 21. Februar 2018 15:25
> An: TRNSYS users mailing list at OneBuilding.org <trnsys-users at lists.onebuilding.org>
> Cc: maverickxxx1991 <maverickxxx1991 at googlemail.com>
> Betreff: Re: [TRNSYS-users] Component Order
> 
> Hi, 
> TRNSYS 17, 64bit.
> 
>> Am 21.02.2018 um 15:23 schrieb hotline via TRNSYS-users <trnsys-users at lists.onebuilding.org>:
>> 
>> Hey Maverick,
>> 
>> which TRNSYS Version do you use? If TRNSYS 18, 32/64 bit?
>> 
>> Regards,
>> Christoph
>> 
>> -----Ursprüngliche Nachricht-----
>> Von: TRNSYS-users [mailto:trnsys-users-bounces at lists.onebuilding.org] Im Auftrag von maverickxxx1991 via TRNSYS-users
>> Gesendet: Mittwoch, 21. Februar 2018 13:01
>> An: TRNSYS-users at lists.onebuilding.org
>> Cc: maverickxxx1991 <maverickxxx1991 at googlemail.com>
>> Betreff: [TRNSYS-users] Component Order
>> 
>> Hey,
>> 
>> I’ve a system with a solar loop, a storage tank (type 340) and 4 heat exchangers running at different times. Sometimes more than one heat exchanger is running and then I get a „difference in power balance“ in type 340. How can I fix that problem? At the moment the storage tank is one of first components loaded, then the solar loop and at the end the heat exchangers in order 1 to 4. I think the problem is that first the storage tank is proofed by it’s temperatures. Than the solar loop load it if the temperatures are too low or not if they are too high. If the storage is load, the temperatures would change, but it’s not calculated after the solar loop again, so that the heat exchangers will proof the initial values of the storage tank and will transfer heat if the temperatures are high enough. They don’t take the new values after solar loop- The control is given at the solar loop and the heat exchanger by type 2b’s. 
>> 
>> Am I right? How can I fix that?
>> 
>> Best regards
>> maverick
>> _______________________________________________
>> TRNSYS-users mailing list
>> TRNSYS-users at lists.onebuilding.org
>> http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org
>> _______________________________________________
>> TRNSYS-users mailing list
>> TRNSYS-users at lists.onebuilding.org
>> http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org
> 
> _______________________________________________
> TRNSYS-users mailing list
> TRNSYS-users at lists.onebuilding.org
> http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org
> _______________________________________________
> TRNSYS-users mailing list
> TRNSYS-users at lists.onebuilding.org
> http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org