[TRNSYS-users] Type 534

Mon Apr 16 01:19:22 PDT 2018

Hi Jeff,

thanks for the answer. Ok, you are right. I will use the user-supplied properties. But what do you mean with “But when I simply specify the file in the Files tab of the proforma it runs fine here in TRNSYS.” I never get it run. Whatever I try always the two Error messages appear:

*** Fatal Error at time   :         0.000000
    Generated by Unit     :     2
    Generated by Type     :   534
    Message               : The storage tank model was unable to read the parameter values from the supplied data file.  Please check the location and format of this data file carefully.

*** Fatal Error at time   :         0.000000
    Generated by Unit     : Not applicable or not available
    Generated by Type     :   534
    TRNSYS Message    105 : A TYPE was called in the TRNSYS input file but was either not linked into trndll.dll or was not found in an external dll. A dummy subroutine was called in its place. Please link the TYPE or remove it from the input file
    Reported information  : Reported by LinkCk

Hopefully you can come around with a solution.

Best,
Hermann.

_______________________________________________________________

DI Dr. mont. Hermann Schranzhofer
Institut fuer Wärmetechnik / Institute of Thermal Engineering
TU Graz / Graz University of Technology
Inffeldgasse 25 / B, A-8010 Graz

Tel.:        +43 316 873 7314
mobil:     +43 664 60 873 7314
Fax :        +43 316 873 7305
http://www.iwt.tugraz.at/
_______________________________________________________________

Von: TRNSYS-users [mailto:trnsys-users-bounces at lists.onebuilding.org] Im Auftrag von Jeff Thornton via TRNSYS-users
Gesendet: Freitag, 13. April 2018 22:30
An: TRNSYS users mailing list at OneBuilding.org <trnsys-users at lists.onebuilding.org>
Cc: Jeff Thornton <thornton at tess-inc.com>
Betreff: Re: [TRNSYS-users] Type 534

The good news is that I can repeat the error with the Type 534 plug-in here.  The bad news is that I don't know yet what's causing the issue.  But when I simply specify the file in the Files tab of the proforma it runs fine here in TRNSYS.  One thing I did notice was that you are using the setting for pure water.  While that model is able to handle the temperature dependence of pure water, any downstream components likely cannot - which can cause energy balance issues.  We recommend using the user-supplied properties option for this reason.  We'll look into the Type 534 plug-in  issue and report back.

Jeff

---
Jeff Thornton

President - TESS LLC

22 N. Carroll Street, Madison WI USA 53703

Office: (608) 274-2577  Fax: (608) 278-1475

www.tess-inc.com<http://www.tess-inc.com>

E-Mail: thornton at tess-inc.com<mailto:thornton at tess-inc.com>

On 04/13/2018 2:19 am, Schranzhofer, Hermann via TRNSYS-users wrote:
Hi Jeff,

It is just a simple example. Find attached the data file and the studio file. TRNSYS Version is 17.02.0004.

Thanks,

Hermann.

Von: TRNSYS-users [mailto:trnsys-users-bounces at lists.onebuilding.org] Im Auftrag von Jeff Thornton via TRNSYS-users
Gesendet: Donnerstag, 12. April 2018 18:34
An: TRNSYS users mailing list at OneBuilding.org <trnsys-users at lists.onebuilding.org<mailto:trnsys-users at lists.onebuilding.org>>
Cc: Jeff Thornton <thornton at tess-inc.com<mailto:thornton at tess-inc.com>>
Betreff: Re: [TRNSYS-users] Type 534

Send us your data file and we'll take a look at it.  Which TRNSYS version are you using?  Are you supplying the correct data file name on the files tabk of the proformaa?

Jeff

---
Jeff Thornton

President - TESS LLC

22 N. Carroll Street, Madison WI USA 53703

Office: (608) 274-2577  Fax: (608) 278-1475

www.tess-inc.com<http://www.tess-inc.com>

E-Mail: thornton at tess-inc.com<mailto:thornton at tess-inc.com>

On 04/12/2018 10:27 am, Schranzhofer, Hermann via TRNSYS-users wrote:
Hi,

I want to use the TESS storage tank model Type 534 for some simulations. What I need is stratified inlets. As far as I can see this is not possible with the proforma without plugin (the parameters are locked).
So I tried my best with the plugin. Configuration is no problem but if I press the OK button in the plugin a message appears telling me “Problem reading cycle number iteration”.
If I start the simulation anyway I get the Fatal Errors below:

*** Fatal Error at time   :         0.000000
    Generated by Unit     :     6
    Generated by Type     :   534
    Message               : The storage tank model was unable to read the parameter values from the supplied data file.  Please check the location and format of this data file carefully.

*** Fatal Error at time   :         0.000000
    Generated by Unit     : Not applicable or not available
    Generated by Type     :   534
    TRNSYS Message    105 : A TYPE was called in the TRNSYS input file but was either not linked into trndll.dll or was not found in an external dll. A dummy subroutine was called in its place. Please link the TYPE or remove it from the input file
    Reported information  : Reported by LinkCk

Is there any help for this problem?

Regards,
Hermann.

_______________________________________________

TRNSYS-users mailing list

TRNSYS-users at lists.onebuilding.org<mailto:TRNSYS-users at lists.onebuilding.org>

http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org

_______________________________________________

TRNSYS-users mailing list

TRNSYS-users at lists.onebuilding.org<mailto:TRNSYS-users at lists.onebuilding.org>

http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.onebuilding.org/pipermail/trnsys-users-onebuilding.org/attachments/20180416/ef08598e/attachment.htm>