[TRNSYS-users] Borehole Model from TESS

Sat Aug 5 15:21:40 PDT 2017

Yang, 

There is an aquifer thermal energy storage model (TRNATES) available
from your distributor (TESS, TRANSSOLAR etc.). We've used it a few times
with pretty good results but it does have a few limitations (the bores
don't interact thermally for example). We've also managed to couple
MODFLOW and MT3D with TRNSYS (popular groundwater models) and can
provide more information if needed. 

Jeff 

---
Jeff Thornton
President - TESS LLC
22 N. Carroll Street, Madison WI USA 53703
Office: (608) 274-2577 Fax: (608) 278-1475
www.tess-inc.com
E-Mail: thornton at tess-inc.com

On 08/05/2017 12:30 pm, WANG Yang via TRNSYS-users wrote: 

> Dear all, 
> 
> I am modeling a OPEN LOOP BOREHOLE SYSTEM FOR TWO OPEN WELLS, one for abstracting underground water, another well for discharging, using TESS lib. However, I'd like to ask you WHICH TYPE is available for Open Loop Borehole system? I just found a Type 557 for U-tube borehole. 
> 
> Look forward to your reply. 
> 
> Many thanks 
> 
> Br 
> 
> Yang 
> 
> 2017-08-02 10:53 GMT+01:00 WANG Yang <wanghongyang1767 at gmail.com>:
> 
> Dear all, 
> 
> I'd like to ask you one question about the error for Radiator Type 1231 shown in attached picture. 
> 
> I used its heat transfer rate output to connect Type 56's own-defined input as the heating power. Then it appears that error. If I delete Radiator Type 1231, it runs well. 
> 
> Many thanks 
> 
> Br. 
> 
> Yang 
> 
> 2017-08-01 21:12 GMT+01:00 via TRNSYS-users <trnsys-users at lists.onebuilding.org>:
> Send TRNSYS-users mailing list submissions to
> trnsys-users at lists.onebuilding.org
> 
> To subscribe or unsubscribe via the World Wide Web, visit
> http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org [4]
> 
> or, via email, send a message with subject or body 'help' to
> trnsys-users-request at lists.onebuilding.org
> 
> You can reach the person managing the list at
> trnsys-users-owner at lists.onebuilding.org
> 
> When replying, please edit your Subject line so it is more specific
> than "Re: Contents of TRNSYS-users digest..."
> 
> Today's Topics:
> 
> 1. Re: variable timestep (Domenico Mazzeo via TRNSYS-users)
> 2. Re: Exact same control signal for different Type 11f gives
> diferent results. (Jeff Thornton via TRNSYS-users)
> 
> ---------- 已转发邮件 ----------
> From: Domenico Mazzeo via TRNSYS-users <trnsys-users at lists.onebuilding.org>
> To: "TRNSYS users mailing list at OneBuilding.org" <trnsys-users at lists.onebuilding.org>, Jeff Thornton <thornton at tess-inc.com>
> Cc: Jorge Facao <jorge.facao at lneg.pt>
> Bcc: 
> Date: Tue, 1 Aug 2017 18:09:08 +0200
> Subject: Re: [TRNSYS-users] variable timestep
> 
> You could run more simulation with different time steps. 
> Then you could join the results with a variable time step. 
> Regards 
> 
> Il 01 Ago 2017 16:53, "Jeff Thornton via TRNSYS-users" <trnsys-users at lists.onebuilding.org> ha scritto:
> No, TRNSYS uses a fixed time step for the duration of the simulation.
> 
> Jeff
> 
> Sent from my iPhone
> 
>> On Jul 31, 2017, at 11:10 AM, Jorge Facao via TRNSYS-users <trnsys-users at lists.onebuilding.org> wrote:
>>
>> Hello,
>> Is it possible to run a simulation with variable time-step in TRNSYS 17?
>> I have tried to put a time-step as a string in control cards but TRNSYS
>> consider the initial value of the string for all simulation.
>> Thanks in advance and best regards,
>>
>> --
>> Jorge Facão
>>
>> Laboratório Nacional de Energia e Geologia (LNEG)
>> Laboratório de Energia Solar
>> Estrada do Paço do Lumiar, 22
>> 1649-038 Lisboa - Portugal
>> T: +351-210924600 [5]/1; Ext: 4379
>> skype: jfacao
>>
>> - AVISO -
>>
>> Esta mensagem de correio eletrónico e quaisquer dos seus ficheiros anexos, caso existam, são confidenciais e destinados apenas à(s) pessoa(s) ou entidade(s) acima referida(s), podendo conter informação confidencial, privilegiada, a qual não deverá ser divulgada, copiada, gravada ou distribuída nos termos da lei vigente. Se não é o destinatário da mensagem, ou se ela lhe foi enviada por engano, agradecemos que não faça uso ou divulgação da mesma. Se recebeu esta mensagem por engano, por favor avise-nos de imediato, por correio eletrónico, para o endereço acima e apague este e-mail do seu sistema.
>>
>> Obrigado.
>>
>>
>>
>> - NOTICE -
>>
>> This e-mail transmission and eventual attached files are intended only for the use of the individual or entity named above and may contain information that is confidential, privileged and exempt from disclosure under applicable law. If you are not the intended recipient, or if you have received this transmission in error, please immediately notify us by e-mail at the above address and delete this e-mail from your system.
>>
>> Thank you.
>> _______________________________________________
>> TRNSYS-users mailing list
>> TRNSYS-users at lists.onebuilding.org
>> http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org [4]
> 
> _______________________________________________
> TRNSYS-users mailing list
> TRNSYS-users at lists.onebuilding.org
> http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org [4] 
> 
> ------------------------------------------------------------------------------- 
> Il banner è generato automaticamente dal servizio di posta elettronica dell'Università della Calabria 
> 
> [6] 
> 
> ---------- 已转发邮件 ----------
> From: Jeff Thornton via TRNSYS-users <trnsys-users at lists.onebuilding.org>
> To: trnsys-users at lists.onebuilding.org
> Cc: 
> Bcc: 
> Date: Tue, 01 Aug 2017 14:57:14 -0500
> Subject: Re: [TRNSYS-users] Exact same control signal for different Type 11f gives diferent results.
> 
> Javier, 
> 
> That sounds suspiciously like a convergence problem. Have you checked the list file to see if you are running into convergence issues? Have you tried to TRACE the models in question to see what's happening on an iteration by iteration basis? If it's convergence problems then the questions become: are you using a small timestep? Are you using a controller with hysteresis? etc. 
> 
> Jeff 
> 
> ---
> Jeff Thornton
> President - TESS LLC
> 22 N. Carroll Street, Madison WI USA 53703
> Office: (608) 274-2577 [1] Fax: (608) 278-1475 [2]
> www.tess-inc.com [3]
> E-Mail: thornton at tess-inc.com
> 
> On 08/01/2017 7:56 am, Javier Vega via TRNSYS-users wrote: 
> Hello TRNSYS users, 
> 
> I want to use two Type 11f (controller flow diverter) components with the same control signal. One Type 11f redirects solar collector flow 
> (Type 553), while the other redirects another circuit's flow to one an Air-Source Heat Pump or a Water Source Heat Pump (Type 941 or Type 927). The events are supposed to happen at the same time. 
> 
> Monitoring the results, my DHW temperature falls. When I looked it up, the flow diverters aren't working at the same time. And what it's worse, something happens with the Heat Pumps: I studied the control signals, and they are activated at the same time, but the heat pump's circuit redirects the flow when it isn't supposed to happen and also the Heat Pump that by mistakes recieves flow doesn't heat the water flow. This is what bothers me the most because I set the Heating control signal to a constant 1, so everytime the HP recieves flow it heats. 
> 
> I simply don't know how to address this issue, same control signals giving different results, and a Heat Pump that recieves flow by mistake but doesn't heat. I would appreciate some help. 
> 
> Kind Regards,
> Javier Vega 
> Universidad de Concepcion 
> 
> 2017-07-28 15:29 GMT-04:00 Javier Vega <jvega025 at gmail.com>:
> 
> Hello TRNSYS users, 
> 
> I want to use two Type 11f (controller flow diverter) components with the same control signal. One Type 11f redirects solar collector flow 
> (Type 553), while the other redirects another circuit's flow to one an Air-Source Heat Pump or a Water Source Heat Pump (Type 941 or Type 927). The events are supposed to happen at the same time. 
> 
> Monitoring the results, my DHW temperature falls. When I looked it up, the flow diverters aren't working at the same time. And what it's worse, something happens with the Heat Pumps: I studied the control signals, and they are activated at the same time, but the heat pump's circuit redirects the flow when it isn't supposed to happen and also the Heat Pump that by mistakes recieves flow doesn't heat the water flow. This is what bothers me the most because I set the Heating control signal to a constant 1, so everytime the HP recieves flow it heats. 
> 
> I simply don't know how to address this issue, same control signals giving different results, and a Heat Pump that recieves flow by mistake but doesn't heat. I would appreciate some help. 
> 
> Kind Regards,
> Javier Vega 
> Universidad de Concepcion 
> 
> _______________________________________________
> TRNSYS-users mailing list
> TRNSYS-users at lists.onebuilding.org
> http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org [4]

_______________________________________________
 TRNSYS-users mailing list
TRNSYS-users at lists.onebuilding.org
http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org
[4]

_______________________________________________
TRNSYS-users mailing list
TRNSYS-users at lists.onebuilding.org
http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org
[4]

Links:
------
[1] tel:(608)%20274-2577
[2] tel:(608)%20278-1475
[3] http://www.tess-inc.com
[4]
http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org
[5] tel:%2B351-210924600
[6] http://www.unical.it
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.onebuilding.org/pipermail/trnsys-users-onebuilding.org/attachments/20170805/6d083746/attachment-0002.htm>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: blocked.gif
Type: image/gif
Size: 118 bytes
Desc: not available
URL: <http://lists.onebuilding.org/pipermail/trnsys-users-onebuilding.org/attachments/20170805/6d083746/attachment-0003.gif>