[TRNSYS-users] Visual Fortran run-time error

Chaminda Ranaweera via TRNSYS-users trnsys-users at lists.onebuilding.org
Tue May 24 04:12:52 PDT 2016


Hello;

Can anybody kindly tell me the meaning of “Array slope”, 
of Solar PV “Input” of “Type 94-a” Solar PV Panels. I 
change the “Array slope” parameter and see the output. 
But, I couldn’t see any significant variation of output of 
solar PV panels. It has not defined this parameter or sign 
convention for that on help manual

I am modeling an array f solar PV panels, I use “Collector 
Array Shading” for that. It also has “Collector Slope” as 
“Parameter”. Is that same as ““Array slope” parameter of 
“Type 94-a”, Solar PV panel.
The “Weather Data Reading and Processing” also has “Slope 
of surface” and “Azimuth of surface”. But it is also not 
defined the sign convention for above two parameters in 
“Help Manuals”.
How can we define above three parameters? Can anybody tell 
me?

According to my knowledge, the maximum solar PV gain shall 
be when it is oriented towards southern, when we stay in 
northern hemisphere. But I always gets the maximum solar 
pv output when Slope of Solar PV is “0” degrees, that 
means when it is horizontal.

Thank You,

Chaminda

On Mon, 23 May 2016 19:19:30 +0200
  Chaminda Ranaweera via TRNSYS-users 
<trnsys-users at lists.onebuilding.org> wrote:
> Hi,
> 
> I also had the same problem earlier, the problem was 
>there was no enough data rows in weather file. I made my 
>weather file with a note pad program. The weather data 
>must be a multiple of 24.
> 
> Chaminda
> 
> On Fri, 20 May 2016 23:44:06 +0000
>  Eleftherios Bourdakis via 
>TRNSYS-users	<trnsys-users at lists.onebuilding.org> wrote:
>> Dear TRNSYS users,
>> 
>> When I change the simulation start time from anything 
>>different than 0 hr, I get the following error:
>> 
>> forrtl: severe (408): fort: (2): Subscript #1 of the 
>>array VALUE_NOW has value 37 which is greater than the 
>>upper bound of 36.
>> 
>> Do you know how I can solve this issue? Up to today 
>>TRNSYS was working fine and I could start my simulation 
>>at any time I wanted.
>> Thank you in advance for your help.
>> 
>> Best regards,
>> Eleftherios Bourdakis
>> PhD Student
>> International Centre for Indoor Εnvironment and Energy
>> 
>> Technical University of Denmark
>> 
>> [cid:image001.png at 01D1B2B3.C9DA92D0]
>> 
>> Department of Civil Engineering
>> 
>> Nils Koppels Allé
>> 
>> Building 402, Office 227
>> 
>> 2800  Kgs. Lyngby, Denmark
>> 
>> Mobile: (+45) 91940297
>> Tel dir: (+45) 45254017
>> 
>> Email: elefbur at byg.dtu.dk<mailto:elefbur at byg.dtu.dk>
>> 
>> Web: www.byg.dtu.dk<http://www.byg.dtu.dk>
>> 
>> 
> 
> _______________________________________________
> TRNSYS-users mailing list
> TRNSYS-users at lists.onebuilding.org
> http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org




More information about the TRNSYS-users mailing list