Dear all,
In short, I'm facing a problem in which I would like to use a formula for cooling which works perfectly for heating, but gives convergence errors when I apply it to my cooling temperature. It occurs when I'm using adaptive temperature limits in an energy calculation to find the efficiency of a certain shading device. I tried increasing the thermal capacitance to 5*1.2*1.007*roomvolume, the moisture capacitance to 7, I've used time steps varying from 5 minutes to 1 hour, but nothing works. Eventually this results in a fatal error, or if I increase the Limits drastically it only slows down my simulation enormously. I'm using Trnsys 17 by the way.
Problem descriptionI've used a 4199.1 kJ/h for both heating and cooling, so given a floor area of 19.44m2 that would be 60W/m2. I've included a file of a project where I isolated this adaptive temperature limit and heating/cooling schedule, so without any shading. One of them shows the situation when there are no convergence errors, but T_Cool_On remains zero degrees, and the other one where in my mind the formula is correct, but convergence errors occur. I think I found where the problem occurs, but I don't know what I'm doing wrong. I use a loop from type 56 to an equation, in which the acceptable indoor temperature depends on the outside temperature (people tollerate higher temperatures if it's warm outside as well), and is compared to the actual indoor temperature to see whether the cooling/heating should be on or off. This goes to another equation to incorporate the annual occupancy schedule for heating and cooling, which is then lead back to type 56.
Heating goes fine, cooling becomes a problem
Strangely enough, I use similar formulas for heating and cooling, and while heating does not give any problems, the cooling does. This is what I use:
T_Heat_On = Heating_need*Heating_schedule*(Target_temperature - 15) + 15 --> 'need' and 'schedule' give either a 0 or 1, and in this way the heating goes on either when the indoor temperature drops below the target temperature while the building is occupied, or when the temperature drops below 15 degrees at any time.
T_Cool_On = Cooling_need*Cooling_schedule*(Target_temperature - 30) + 30 --> I tried to do the same for cooling, so it would cool when it would become too hot, or when the temperature would rise above 30 degrees when the building is unoccupied. Strangely enough, this only works when I leave out the maximum of 30 degrees (so T_Cool_On = Cooling_need*Cooling_schedule*Target_temperature), but if I'm not mistaking, this means that at times when the building is not occupied or no cooling is needed, the T_Cool_On is equal to 0, meaning that the heating and cooling start to compete with each other because the cooling 'wants' a lower temperature than the heating. Could someone please tell me what might cause this convergence error, and possibly also how to solve this? Thank you very much in advance! Kind regards, Tom
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.onebuilding.org/pipermail/trnsys-users-onebuilding.org/attachments/20130504/3eb5facb/attachment-0004.htm>
-------------- next part --------------
 TRNSYS - the TRaNsient SYstem Simulation program
The Solar Energy Lab at the University of Wisconsin - Madison, USA
Le Centre Scientifique et Technique du Batiment, Sophia Antipolis, France
Transsolar Energietechnik GmBH, Stuttgart, Germany
Thermal Energy System Specialists, LLC, Madison Wisconsin, USA
Release 17.01.0025
Listing file for: "C:\Trnsys17\MyProjects\BuildingProject9\BuildingProject9.dck"
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : The TRNSYS Executable (TRNExe.exe) and main DLL (TRNDll.dll) are located in "C:\Trnsys17\Exe"
*** Pre-Processing the TRNSYS EQUATIONs and CONSTANTs to check for fatal errors.
*** Warning at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 11 : The TRNSYS processor has reported an illegal variable name in an EQUATIONS or CONSTANTS card. Equations or constants must not begin with END, INC, EQU or CON as these are protected codes required when reading the TRNSYS input file. The offending variable name is listed below.
Reported information : CONTROL_COMFORT
*** Warning at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 11 : The TRNSYS processor has reported an illegal variable name in an EQUATIONS or CONSTANTS card. Equations or constants must not begin with END, INC, EQU or CON as these are protected codes required when reading the TRNSYS input file. The offending variable name is listed below.
Reported information : CONTROL_COLD
*** Warning at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 11 : The TRNSYS processor has reported an illegal variable name in an EQUATIONS or CONSTANTS card. Equations or constants must not begin with END, INC, EQU or CON as these are protected codes required when reading the TRNSYS input file. The offending variable name is listed below.
Reported information : CONTROL_WARM
*** Warning at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 11 : The TRNSYS processor has reported an illegal variable name in an EQUATIONS or CONSTANTS card. Equations or constants must not begin with END, INC, EQU or CON as these are protected codes required when reading the TRNSYS input file. The offending variable name is listed below.
Reported information : CONTROL_TOTAL
*** Pre-Processing of EQUATIONs and CONSTANTs completed with no fatal errors found.
*** Evaluating the EQUATIONs and CONSTANTs to determine their initial values.
*** Finished evaluating the EQUATIONs and CONSTANTs and ready to begin processing the remainder of the TRNSYS input file.
VERSION 17
*******************************************************************************
*** TRNSYS input file (deck) generated by TrnsysStudio
*** on zaterdag, mei 04, 2013 at 13:06
*** from TrnsysStudio project: C:\Trnsys17\MyProjects\BuildingProject9\BuildingProject9.tpf
***
*** If you edit this file, use the File/Import TRNSYS Input File function in
*** TrnsysStudio to update the project.
***
*** If you have problems, questions or suggestions please contact your local
*** TRNSYS distributor or mailto:software at cstb.fr
***
*******************************************************************************
*******************************************************************************
*** Units
*******************************************************************************
*******************************************************************************
*** Control cards
*******************************************************************************
* START, STOP and STEP
CONSTANTS 3
START=0
STOP=8760
STEP=1
! Start time End time Time step
SIMULATION 0.0000000000000000E+00 8.7600000000000000E+03 1.0000000000000000E+00
! Integration Convergence
TOLERANCES 1.0000000000000002E-03 1.0000000000000002E-03
! Max iterations Max warnings Trace limit
LIMITS 30 30 31
! TRNSYS numerical integration solver method
DFQ 1
! TRNSYS output file width, number of characters
WIDTH 72
! NOLIST statement
LIST
! MAP statement
! Solver statement Minimum relaxation factor Maximum relaxation factor
SOLVER 0
1.000000000000000
1.000000000000000
! Nan DEBUG statement
NAN_CHECK 0
! Overwrite DEBUG statement
OVERWRITE_CHECK 0
! disable time report
TIME_REPORT 0
! EQUATION SOLVER statement
EQUATION SOLVING METHOD 0
* User defined CONSTANTS
* EQUATIONS "Turn"
*
EQUATIONS 13
TURN = 0
! northern hemisphere: 1 - southern hemisphere: -1
HEMISPHERE = 1
! azimuth angle of orientation
AA_H_0_0 = 0
! azimuth angle of orientation
AA_S_0_90 = (0 +TURN)*GT(HEMISPHERE,0)+ (180-0 -TURN)*NOT(GT(HEMISPHERE,0))
! azimuth angle of orientation
AA_W_45_90 = (45 +TURN)*GT(HEMISPHERE,0)+ (180-45-TURN)*NOT(GT(HEMISPHERE,0))
! azimuth angle of orientation
AA_W_90_90 = (90 +TURN)*GT(HEMISPHERE,0)+ (180-90-TURN)*NOT(GT(HEMISPHERE,0))
! azimuth angle of orientation
AA_N_135_90 = (135+TURN)*GT(HEMISPHERE,0)+ (180-135-TURN)*NOT(GT(HEMISPHERE,0))
! azimuth angle of orientation
AA_N_180_90 = (180+TURN)*GT(HEMISPHERE,0)+ (180-180-TURN)*NOT(GT(HEMISPHERE,0))
! azimuth angle of orientation
AA_E_225_90 = (225+TURN)*GT(HEMISPHERE,0)+ (180-225-TURN)*NOT(GT(HEMISPHERE,0))
! azimuth angle of orientation
AA_E_270_90 = (270+TURN)*GT(HEMISPHERE,0)+ (180-270-TURN)*NOT(GT(HEMISPHERE,0))
! azimuth angle of orientation
AA_S_315_90 = (315+TURN)*GT(HEMISPHERE,0)+ (180-315-TURN)*NOT(GT(HEMISPHERE,0))
!solar azimuth corrected for southern hemisphere such that north=180, south=0, west =90, east=-90
AAZM_CORR_HEM = AAZM*GT(HEMISPHERE,0) + NOT(GT(HEMISPHERE,0))*((180-AAZM)*GT(AAZM,0)*LE(AAZM,180) + (-180-AAZM)*NOT(GT(AAZM,0)*LE(AAZM,180)))
! solar azimuth corrected by building rotation - Input for Type 56 sun position for SHM and ISM
AAZM_TYPE56 = (AAZM_CORR_HEM - TURN)
*$UNIT_NAME Turn
*$LAYER Main
*$POSITION 52 63
*------------------------------------------------------------------------------
* EQUATIONS "Radiation"
*
EQUATIONS 31
AZEN = [15,16]
AAZM = [15,17]
!Sky diffuse radiation on the horizontal
ID_H_0_0 = [15,20]
!Total incident of radation orientation H_0_0
IT_H_0_0 = [15,24]
!Beam incident of radation orientation H_0_0
IB_H_0_0 = [15,33]
!Incident angle of orientation H_0_0
AI_H_0_0 = [15,69]
IT_S_0_90 = [15,25]
IB_S_0_90 = [15,34]
AI_S_0_90 = [15,70]
IT_W_45_90 = [15,26]
IB_W_45_90 = [15,35]
AI_W_45_90 = [15,71]
IT_W_90_90 = [15,27]
IB_W_90_90 = [15,36]
AI_W_90_90 = [15,72]
IT_N_135_90 = [15,28]
IB_N_135_90 = [15,37]
AI_N_135_90 = [15,73]
IT_N_180_90 = [15,29]
IB_N_180_90 = [15,38]
AI_N_180_90 = [15,74]
IT_E_225_90 = [15,30]
IB_E_225_90 = [15,39]
AI_E_225_90 = [15,75]
IT_E_270_90 = [15,31]
IB_E_270_90 = [15,40]
AI_E_270_90 = [15,76]
IT_S_315_90 = [15,32]
IB_S_315_90 = [15,41]
AI_S_315_90 = [15,77]
hour_of_day = MOD(TIME,24)
*$UNIT_NAME Radiation
*$LAYER Main
*$POSITION 203 127
*------------------------------------------------------------------------------
* EQUATIONS "Cooling"
*
EQUATIONS 1
T_COOL_ON = max( min( 27, ([15,1]/3+49/3) ), 25)
*$UNIT_NAME Cooling
*$LAYER Main
*$POSITION 672 596
*------------------------------------------------------------------------------
* EQUATIONS "Shading+Light"
*
EQUATIONS 1
! 27
BRIGHT = [200,1]
*$UNIT_NAME Shading+Light
*$LAYER Controls
*$POSITION 661 724
*------------------------------------------------------------------------------
* Model "Weather data" (Type 15)
*
UNIT 15 TYPE 15 data
*$UNIT_NAME Weather data
*$MODEL .\Weather Data Reading and Processing\Standard Format\TMY2\Type15-2.tmf
*$POSITION 96 202
*$LAYER Main #
PARAMETERS 33
! 1 File Type
! 2 Logical unit
! 3 Tilted Surface Radiation Mode
! 4 Ground reflectance - no snow
! 5 Ground reflectance - snow cover
! 6 Number of surfaces
! 7 Tracking mode-1
! 8 Slope of surface-1
! 9 Azimuth of surface-1
! 10 Tracking mode-2
! 11 Slope of surface-2
! 12 Azimuth of surface-2
! 13 Tracking mode-3
! 14 Slope of surface-3
! 15 Azimuth of surface-3
! 16 Tracking mode-4
! 17 Slope of surface-4
! 18 Azimuth of surface-4
! 19 Tracking mode-5
! 20 Slope of surface-5
! 21 Azimuth of surface-5
! 22 Tracking mode-6
! 23 Slope of surface-6
! 24 Azimuth of surface-6
! 25 Tracking mode-7
! 26 Slope of surface-7
! 27 Azimuth of surface-7
! 28 Tracking mode-8
! 29 Slope of surface-8
! 30 Azimuth of surface-8
! 31 Tracking mode-9
! 32 Slope of surface-9
! 33 Azimuth of surface-9
2.0000000000000000E+00 3.4000000000000000E+01 5.0000000000000000E+00 2.0000000000000001E-01 7.0000000000000007E-01
9.0000000000000000E+00 1.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 1.0000000000000000E+00
9.0000000000000000E+01 0.0000000000000000E+00 1.0000000000000000E+00 9.0000000000000000E+01 4.5000000000000000E+01
1.0000000000000000E+00 9.0000000000000000E+01 9.0000000000000000E+01 1.0000000000000000E+00 9.0000000000000000E+01
1.3500000000000000E+02 1.0000000000000000E+00 9.0000000000000000E+01 1.8000000000000000E+02 1.0000000000000000E+00
9.0000000000000000E+01 2.2500000000000000E+02 1.0000000000000000E+00 9.0000000000000000E+01 2.7000000000000000E+02
1.0000000000000000E+00 9.0000000000000000E+01 3.1500000000000000E+02
*** External files
ASSIGN C:\Trnsys17\Weather\Meteonorm\Europe\NL-Amsterdam-Schiphol-62400.tm2 34
*|? Which file contains the TMY-2 weather data? |1000
*------------------------------------------------------------------------------
* EQUATIONS "Light Thresholds"
*
EQUATIONS 2
IT_LIGHT_ON = -3.6*120
IT_LIGHT_OFF = -3.6*200
*$UNIT_NAME Light Thresholds
*$LAYER Controls
*$POSITION 469 532
*------------------------------------------------------------------------------
* Model "Lights" (Type 2)
*
UNIT 200 TYPE 2
*$UNIT_NAME Lights
*$MODEL .\Controllers\Differential Controller w_ Hysteresis\generic\Solver 0 (Successive Substitution) Control Strategy\Type2d.tmf
*$POSITION 559 543
*$LAYER Controls #
*$# NOTE: This controller can only be used with Solver 0 (Successive substitution)
*$#
*$#
*$#
*$#
*$#
*$#
*$#
*$#
*$#
PARAMETERS 2
! 1 No. of oscillations
! 2 High limit cut-out
5.0000000000000000E+00 4.0000000000000000E+04
INPUTS 6
! [unconnected] Upper input value
! Radiation:IT_H_0_0 ->Lower input value
! [unconnected] Monitoring value
! Lights:Output control function ->Input control function
! [equation] Upper dead band
! [equation] Lower dead band
CONST IT_H_0_0 CONST 200,1 IT_LIGHT_ON
IT_LIGHT_OFF
*** INITIAL INPUT VALUES
0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 -4.3200000000000000E+02
-7.2000000000000000E+02
*------------------------------------------------------------------------------
* Model "Building" (Type 56)
*
UNIT 56 TYPE 56
*$UNIT_NAME Building
*$MODEL .\Loads and Structures\Multi-Zone Building\Type56.tmf
*$POSITION 824 578
*$LAYER Main # #
*$#
PARAMETERS 3
! 1 Logical unit for building description file (.bui)
! 2 Star network calculation switch
! 3 Weighting factor for operative temperature
3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
INPUTS 29
! Tout:output -> 1- TAMB
! Weather data:Percent relative humidity -> 2- RELHUMAMB
! Weather data:Effective sky temperature -> 3- TSKY
! Tout:output -> 4- TSGRD
! Weather data:Solar zenith angle -> 5- AZEN
! Turn:AAZM_TYPE56 -> 6- AAZM
! Radiation:IT_N_180_90 -> 7- IT_N_180_90
! Radiation:IT_S_0_90 -> 8- IT_S_0_90
! Radiation:IT_E_270_90 -> 9- IT_E_270_90
! Radiation:IT_W_90_90 -> 10- IT_W_90_90
! Radiation:IT_H_0_0 -> 11- IT_H_0_0
! Radiation:IB_N_180_90 -> 12- IB_N_180_90
! Radiation:IB_S_0_90 -> 13- IB_S_0_90
! Radiation:IB_E_270_90 -> 14- IB_E_270_90
! Radiation:IB_W_90_90 -> 15- IB_W_90_90
! Radiation:IB_H_0_0 -> 16- IB_H_0_0
! Radiation:AI_N_180_90 -> 17- AI_N_180_90
! Radiation:AI_S_0_90 -> 18- AI_S_0_90
! Radiation:AI_E_270_90 -> 19- AI_E_270_90
! Radiation:AI_W_90_90 -> 20- AI_W_90_90
! Radiation:AI_H_0_0 -> 21- AI_H_0_0
! Weather data:Ground reflectance -> 22- GRDREF
! [unconnected] 23- CNAT_1
! Schedules:T_Cool_On_2 -> 24- T_COOL_ON
! [unconnected] 25- MS_N_180_90
! [unconnected] 26- MS_S_0_90
! [unconnected] 27- MS_E_270_90
! [unconnected] 28- MS_W_90_90
! Shading+Light:BRIGHT -> 29- BRIGHT
16,1 15,7 15,4 16,1 15,16
AAZM_TYPE56 IT_N_180_90 IT_S_0_90 IT_E_270_90 IT_W_90_90
IT_H_0_0 IB_N_180_90 IB_S_0_90 IB_E_270_90 IB_W_90_90
IB_H_0_0 AI_N_180_90 AI_S_0_90 AI_E_270_90 AI_W_90_90
AI_H_0_0 15,123 CONST T_COOL_ON_2 CONST
CONST CONST CONST BRIGHT
*** INITIAL INPUT VALUES
0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
0.0000000000000000E+00 2.0000000000000001E-01 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
*** External files
ASSIGN BuildingProject9.b17 35
*|? Building description file (*.bui) |1000
*------------------------------------------------------------------------------
* Model "Temperature" (Type 65)
*
UNIT 25 TYPE 65
*$UNIT_NAME Temperature
*$MODEL .\Output\Online Plotter\Online Plotter Without File\Type65d.tmf
*$POSITION 1089 650
*$LAYER Main # #
PARAMETERS 12
! 1 Nb. of left-axis variables
! 2 Nb. of right-axis variables
! 3 Left axis minimum
! 4 Left axis maximum
! 5 Right axis minimum
! 6 Right axis maximum
! 7 Number of plots per simulation
! 8 X-axis gridpoints
! 9 Shut off Online w/o removing
! 10 Logical unit for output file
! 11 Output file units
! 12 Output file delimiter
2.0000000000000000E+00 3.0000000000000000E+00 -2.0000000000000000E+03 5.0000000000000000E+03 -1.5000000000000000E+01
3.5000000000000000E+01 1.0000000000000000E+00 1.2000000000000000E+01 0.0000000000000000E+00 -1.0000000000000000E+00
0.0000000000000000E+00 0.0000000000000000E+00
INPUTS 5
! Schedules:Cooling ->Left axis variable-1
! Schedules:Heating ->Left axis variable-2
! Schedules:T_Cool_On_2 ->Right axis variable-1
! Schedules:T_Heat_On ->Right axis variable-2
! Cooling:T_COOL_ON ->Right axis variable-3
COOLING HEATING T_COOL_ON_2 T_HEAT_ON T_COOL_ON
*** INITIAL INPUT VALUES
Cooling Heating TCOOL_TEST _ATG THEAT _TEST_ATG TCOOL_TEST_ATG
LABELS 3
ATG Controls
Temperatures ATG [deg C]
ATG temperatures
*------------------------------------------------------------------------------
* Model "Irradiation" (Type 65)
*
UNIT 66 TYPE 65
*$UNIT_NAME Irradiation
*$MODEL .\Output\Online Plotter\Online Plotter Without File\Type65d.tmf
*$POSITION 915 84
*$LAYER Main # #
PARAMETERS 12
! 1 Nb. of left-axis variables
! 2 Nb. of right-axis variables
! 3 Left axis minimum
! 4 Left axis maximum
! 5 Right axis minimum
! 6 Right axis maximum
! 7 Number of plots per simulation
! 8 X-axis gridpoints
! 9 Shut off Online w/o removing
! 10 Logical unit for output file
! 11 Output file units
! 12 Output file delimiter
5.0000000000000000E+00 6.0000000000000000E+00 0.0000000000000000E+00 3.6000000000000000E+03 0.0000000000000000E+00
3.6000000000000000E+03 1.0000000000000000E+00 1.2000000000000000E+01 0.0000000000000000E+00 -1.0000000000000000E+00
0.0000000000000000E+00 0.0000000000000000E+00
INPUTS 11
! Radiation:IT_H_0_0 ->Left axis variable-1
! Radiation:IT_S_0_90 ->Left axis variable-2
! Radiation:IT_W_90_90 ->Left axis variable-3
! Radiation:IT_N_180_90 ->Left axis variable-4
! Radiation:IT_E_270_90 ->Left axis variable-5
! Radiation:IB_H_0_0 ->Right axis variable-1
! Radiation:IB_S_0_90 ->Right axis variable-2
! Radiation:IB_W_90_90 ->Right axis variable-3
! Radiation:IB_N_180_90 ->Right axis variable-4
! Radiation:IB_E_270_90 ->Right axis variable-5
! Radiation:hour_of_day ->Right axis variable-6
IT_H_0_0 IT_S_0_90 IT_W_90_90 IT_N_180_90 IT_E_270_90
IB_H_0_0 IB_S_0_90 IB_W_90_90 IB_N_180_90 IB_E_270_90
HOUR_OF_DAY
*** INITIAL INPUT VALUES
IT_H_0_0 IT_S_0_90 IT_W_90_90 IT_N_ 180_90 IT_E_270_90
IB_H_0_0 IB_S_0_90 IB_W_90_90 IB_N_ 180_90 IB_E_270_90
hour_of_day
LABELS 3
Total Incident Solar Radition [kJ/hr m²]
Beam Incident Solar Radition [kJ/hr m²]
Irradition
*------------------------------------------------------------------------------
* EQUATIONS "ATG"
*
EQUATIONS 7
Tcomfort = 21.45+0.11*[13,1]
Th90 = 23.45+0.11*[13,1]
Tl90 = 19.45+0.11*[13,1]
Control_comfort = ae(Tcomfort,[56,1],2)
*** Warning at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 11 : The TRNSYS processor has reported an illegal variable name in an EQUATIONS or CONSTANTS card. Equations or constants must not begin with END, INC, EQU or CON as these are protected codes required when reading the TRNSYS input file. The offending variable name is listed below.
Reported information : CONTROL_COMFORT
Control_cold = le([56,1],Tl90)
*** Warning at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 11 : The TRNSYS processor has reported an illegal variable name in an EQUATIONS or CONSTANTS card. Equations or constants must not begin with END, INC, EQU or CON as these are protected codes required when reading the TRNSYS input file. The offending variable name is listed below.
Reported information : CONTROL_COLD
Control_warm = ge([56,1],Th90)
*** Warning at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 11 : The TRNSYS processor has reported an illegal variable name in an EQUATIONS or CONSTANTS card. Equations or constants must not begin with END, INC, EQU or CON as these are protected codes required when reading the TRNSYS input file. The offending variable name is listed below.
Reported information : CONTROL_WARM
Control_total = Control_comfort+Control_cold+Control_warm
*** Warning at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 11 : The TRNSYS processor has reported an illegal variable name in an EQUATIONS or CONSTANTS card. Equations or constants must not begin with END, INC, EQU or CON as these are protected codes required when reading the TRNSYS input file. The offending variable name is listed below.
Reported information : CONTROL_TOTAL
*$UNIT_NAME ATG
*$LAYER Main
*$POSITION 820 490
*------------------------------------------------------------------------------
* Model "Teref" (Type 62)
*
UNIT 13 TYPE 62
*$UNIT_NAME Teref
*$MODEL .\Utility\Calling External Programs\Excel\Type62.tmf
*$POSITION 899 404
*$LAYER Main #
PARAMETERS 4
! 1 Mode
! 2 Nb of inputs
! 3 Nb of outputs
! 4 Show Excel
0.0000000000000000E+00 1.0000000000000000E+00 1.0000000000000000E+00 0.0000000000000000E+00
INPUTS 1
! Time:DAYNUM ->input
DAYNUM
*** INITIAL INPUT VALUES
0.0000000000000000E+00
LABELS 1
Afleestabel Teref.xls
*------------------------------------------------------------------------------
* EQUATIONS "Time"
*
EQUATIONS 4
DAYNUM = 1+INT(TIME/24)
WEEK = 1+INT(TIME/(7*24))
DAYWEEK = 7+DAYNUM-WEEK*7
Time_of_year = Time
*$UNIT_NAME Time
*$LAYER Main
*$POSITION 859 258
*------------------------------------------------------------------------------
* Model "Tout" (Type 62)
*
UNIT 16 TYPE 62
*$UNIT_NAME Tout
*$MODEL .\Utility\Calling External Programs\Excel\Type62.tmf
*$POSITION 995 426
*$LAYER Main #
PARAMETERS 4
! 1 Mode
! 2 Nb of inputs
! 3 Nb of outputs
! 4 Show Excel
0.0000000000000000E+00 1.0000000000000000E+00 1.0000000000000000E+00 0.0000000000000000E+00
INPUTS 1
! Time:Time_of_year ->input
TIME_OF_YEAR
*** INITIAL INPUT VALUES
0.0000000000000000E+00
LABELS 1
Afleestabel Tout.xls
*------------------------------------------------------------------------------
* Model "Internal loads" (Type 579)
*
UNIT 17 TYPE 579 loads
*$UNIT_NAME Internal loads
*$MODEL .\Utility Library (TESS)\Forcing Functions\Multi-Level Functions\3-Level Function\Type579.tmf
*$POSITION 195 636
*$LAYER Main #
*$# Possible Uses:
*$# Temperature Setpoints in a House/Building
*$# Ocupancy Patterns for a School
*$# Controller for Detailed Pumping Scheme
PARAMETERS 25
! 1 Number of tiers
! 2 Length of primary cycle
! 3 Length of secondary cycle
! 4 Length of tertiary cycle
! 5 # On Periods - Primary Cycle
! 6 Start of ON Period for Cycle 1
! 7 End of ON Period for Cycle 1
! 8 # On Periods - Secondary Cycle, Primary OFF
! 9 Start of ON Period for Cycle 2
! 10 End of ON Period for Cycle 2
! 11 # On Periods - Secondary Cycle, Primary ON
! 12 Start of ON Period for Cycle 3
! 13 End of ON Period for Cycle 3
! 14 # On Periods - Tertiary Cycle, Primary OFF, Secondary OFF
! 15 Start of ON Period for Cycle 4
! 16 End of ON Period for Cycle 4
! 17 # On Periods - Tertiary Cycle, Primary OFF, Secondary ON
! 18 Start of ON Period for Cycle 5
! 19 End of ON Period for Cycle 5
! 20 # On Periods - Tertiary Cycle, Primary ON, Secondary OFF
! 21 Start of ON Period for Cycle 6
! 22 End of ON Period for Cycle 6
! 23 # On Periods - Tertiary Cycle, Primary ON, Secondary N
! 24 Start of ON Period for Cycle 7
! 25 End of ON Period for Cycle 7
3.0000000000000000E+00 8.7600000000000000E+03 1.6800000000000000E+02 2.4000000000000000E+01 1.0000000000000000E+00
0.0000000000000000E+00 8.7600000000000000E+03 1.0000000000000000E+00 0.0000000000000000E+00 1.2000000000000000E+02
1.0000000000000000E+00 0.0000000000000000E+00 1.2000000000000000E+02 1.0000000000000000E+00 0.0000000000000000E+00
2.4000000000000000E+01 1.0000000000000000E+00 8.0000000000000000E+00 1.8000000000000000E+01 1.0000000000000000E+00
0.0000000000000000E+00 2.4000000000000000E+01 1.0000000000000000E+00 8.0000000000000000E+00 1.8000000000000000E+01
INPUTS 8
! [unconnected] Value of Function (OFF,OFF,OFF)
! [unconnected] Value of Function (OFF,OFF,ON)
! [unconnected] Value of Function (OFF,ON,OFF)
! [unconnected] Value of Function (OFF,ON,ON)
! [unconnected] Value of Function (ON,OFF,OFF)
! [unconnected] Value of Function (ON,OFF,ON)
! [unconnected] Value of Function (ON,ON,OFF)
! [unconnected] Value of Function (ON,ON,ON)
CONST AR CONST CONST CONST 0 CONST 0
CONST CONST CONST
*** INITIAL INPUT VALUES
0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
0.0000000000000000E+00 0.0000000000000000E+00 1.0000000000000000E+00
*------------------------------------------------------------------------------
* Model "Ventilation" (Type 579)
*
UNIT 18 TYPE 579
*$UNIT_NAME Ventilation
*$MODEL .\Utility Library (TESS)\Forcing Functions\Multi-Level Functions\3-Level Function\Type579.tmf
*$POSITION 188 700
*$LAYER Main #
*$# Possible Uses:
*$# Temperature Setpoints in a House/Building
*$# Ocupancy Patterns for a School
*$# Controller for Detailed Pumping Scheme
PARAMETERS 25
! 1 Number of tiers
! 2 Length of primary cycle
! 3 Length of secondary cycle
! 4 Length of tertiary cycle
! 5 # On Periods - Primary Cycle
! 6 Start of ON Period for Cycle 1
! 7 End of ON Period for Cycle 1
! 8 # On Periods - Secondary Cycle, Primary OFF
! 9 Start of ON Period for Cycle 2
! 10 End of ON Period for Cycle 2
! 11 # On Periods - Secondary Cycle, Primary ON
! 12 Start of ON Period for Cycle 3
! 13 End of ON Period for Cycle 3
! 14 # On Periods - Tertiary Cycle, Primary OFF, Secondary OFF
! 15 Start of ON Period for Cycle 4
! 16 End of ON Period for Cycle 4
! 17 # On Periods - Tertiary Cycle, Primary OFF, Secondary ON
! 18 Start of ON Period for Cycle 5
! 19 End of ON Period for Cycle 5
! 20 # On Periods - Tertiary Cycle, Primary ON, Secondary OFF
! 21 Start of ON Period for Cycle 6
! 22 End of ON Period for Cycle 6
! 23 # On Periods - Tertiary Cycle, Primary ON, Secondary N
! 24 Start of ON Period for Cycle 7
! 25 End of ON Period for Cycle 7
3.0000000000000000E+00 8.7600000000000000E+03 1.6800000000000000E+02 2.4000000000000000E+01 1.0000000000000000E+00
0.0000000000000000E+00 8.7600000000000000E+03 1.0000000000000000E+00 0.0000000000000000E+00 1.2000000000000000E+02
1.0000000000000000E+00 0.0000000000000000E+00 1.2000000000000000E+02 1.0000000000000000E+00 0.0000000000000000E+00
2.4000000000000000E+01 1.0000000000000000E+00 7.0000000000000000E+00 1.8000000000000000E+01 1.0000000000000000E+00
0.0000000000000000E+00 2.4000000000000000E+01 1.0000000000000000E+00 7.0000000000000000E+00 1.8000000000000000E+01
INPUTS 8
! [unconnected] Value of Function (OFF,OFF,OFF)
! [unconnected] Value of Function (OFF,OFF,ON)
! [unconnected] Value of Function (OFF,ON,OFF)
! [unconnected] Value of Function (OFF,ON,ON)
! [unconnected] Value of Function (ON,OFF,OFF)
! [unconnected] Value of Function (ON,OFF,ON)
! [unconnected] Value of Function (ON,ON,OFF)
! [unconnected] Value of Function (ON,ON,ON)
CONST AR CONST CONST CONST 0 CONST 0
CONST CONST CONST
*** INITIAL INPUT VALUES
0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
0.0000000000000000E+00 0.0000000000000000E+00 1.0000000000000000E+00
*------------------------------------------------------------------------------
* Model "Heating and cooling" (Type 579)
*
UNIT 19 TYPE 579 and cooling
*$UNIT_NAME Heating and cooling
*$MODEL .\Utility Library (TESS)\Forcing Functions\Multi-Level Functions\3-Level Function\Type579.tmf
*$POSITION 191 764
*$LAYER Main #
*$# Possible Uses:
*$# Temperature Setpoints in a House/Building
*$# Ocupancy Patterns for a School
*$# Controller for Detailed Pumping Scheme
PARAMETERS 25
! 1 Number of tiers
! 2 Length of primary cycle
! 3 Length of secondary cycle
! 4 Length of tertiary cycle
! 5 # On Periods - Primary Cycle
! 6 Start of ON Period for Cycle 1
! 7 End of ON Period for Cycle 1
! 8 # On Periods - Secondary Cycle, Primary OFF
! 9 Start of ON Period for Cycle 2
! 10 End of ON Period for Cycle 2
! 11 # On Periods - Secondary Cycle, Primary ON
! 12 Start of ON Period for Cycle 3
! 13 End of ON Period for Cycle 3
! 14 # On Periods - Tertiary Cycle, Primary OFF, Secondary OFF
! 15 Start of ON Period for Cycle 4
! 16 End of ON Period for Cycle 4
! 17 # On Periods - Tertiary Cycle, Primary OFF, Secondary ON
! 18 Start of ON Period for Cycle 5
! 19 End of ON Period for Cycle 5
! 20 # On Periods - Tertiary Cycle, Primary ON, Secondary OFF
! 21 Start of ON Period for Cycle 6
! 22 End of ON Period for Cycle 6
! 23 # On Periods - Tertiary Cycle, Primary ON, Secondary N
! 24 Start of ON Period for Cycle 7
! 25 End of ON Period for Cycle 7
3.0000000000000000E+00 8.7600000000000000E+03 1.6800000000000000E+02 2.4000000000000000E+01 1.0000000000000000E+00
0.0000000000000000E+00 8.7600000000000000E+03 1.0000000000000000E+00 0.0000000000000000E+00 1.2000000000000000E+02
1.0000000000000000E+00 0.0000000000000000E+00 1.2000000000000000E+02 1.0000000000000000E+00 0.0000000000000000E+00
2.4000000000000000E+01 1.0000000000000000E+00 6.0000000000000000E+00 1.8000000000000000E+01 1.0000000000000000E+00
0.0000000000000000E+00 2.4000000000000000E+01 1.0000000000000000E+00 6.0000000000000000E+00 1.8000000000000000E+01
INPUTS 8
! [unconnected] Value of Function (OFF,OFF,OFF)
! [unconnected] Value of Function (OFF,OFF,ON)
! [unconnected] Value of Function (OFF,ON,OFF)
! [unconnected] Value of Function (OFF,ON,ON)
! [unconnected] Value of Function (ON,OFF,OFF)
! [unconnected] Value of Function (ON,OFF,ON)
! [unconnected] Value of Function (ON,ON,OFF)
! [unconnected] Value of Function (ON,ON,ON)
CONST AR CONST CONST CONST 0 CONST 0
CONST CONST CONST
*** INITIAL INPUT VALUES
0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
0.0000000000000000E+00 0.0000000000000000E+00 1.0000000000000000E+00
*------------------------------------------------------------------------------
* EQUATIONS "Schedules"
*
EQUATIONS 4
Cooling = [19,1]*Control_warm
Heating = [19,1]*Control_cold
T_Heat_On = Heating*(Tl90-15)+15
T_Cool_On_2 = Cooling*(Th90-30)+30
*$UNIT_NAME Schedules
*$LAYER Main
*$POSITION 369 724
*------------------------------------------------------------------------------
END
TRANSIENT SIMULATION STARTING AT TIME = 0.0000000000000000E+00
STOPPING AT TIME = 8.7600000000000000E+03
TIMESTEP = 1 / 1
DIFFERENTIAL EQUATION ERROR TOLERANCE = 1.0000000000000002E-03
ALGEBRAIC CONVERGENCE TOLERANCE = 1.0000000000000002E-03
DIFFERENTIAL EQUATIONS SOLVED BY MODIFIED EULER
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 90 : TRNDll.dll is compiled in release mode. External DLLs will be loaded from the .\UserLib\ReleaseDLLs\ directory.
Reported information : Not available
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : The following Types were loaded from TRNDll.dll: Type62, Type15, Type65, Type2
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "FileReader.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSApplicationsLibrary_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSArchiveDLL_v2.04_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSControllersLibrary_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSElectricalLibrary_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSGHPLibraryType997_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSGHPLibrary_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSGroundCouplingLibrary_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSGroundCouplingType1244_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSGroundCouplingType1255_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSGroundCouplingType1256_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSGroundCouplingType957_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSGroundCouplingType993_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSHVACLibrary_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSHydronics_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSLoadsStructuresLibrary_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSOptimizationLibrary_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSSolarLibrary_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSStorageLibrary_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : The following Types were loaded from "TESSUtilityLibrary_v17.1.03_Release.dll": Type579
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "type127.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "Type157.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : The following Types were loaded from "Type56.dll": Type56
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "Type76Lib.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "type79-W.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "Type79Lib.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "Type82Lib.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 199 : TRNSYS found at least one user DLL in the UserLib directory. (Note: Only DLL's including Types that are used in the simulation are loaded)
Reported information : 2 user DLLs were loaded after searching in "C:\Trnsys17\UserLib\ReleaseDLLs"
*** Notice at time : 0.000000
Generated by Unit : 56
Generated by Type : 56
Message : Shading mask file *.shm for external windows does not exist.
*** Notice at time : 0.000000
Generated by Unit : 56
Generated by Type : 56
Message : TRNFLOW (multi zone air flow model) messages are written in a separate file *.cer! Please, always check the *.cer file for information!!!
*** Notice at time : 0.000000
Generated by Unit : 56
Generated by Type : 56
Message : Active layers and internal window calculations integrated
*** Notice at time : 0.000000
Generated by Unit : 56
Generated by Type : 56
Message : No internal humidity calculations are performed and no condensation warnings are printed. if any of the outputs ntype 9,10,11,26,29,40,41,47,48 or 49 is specified The humidity calculations, using an internal timestep, will be switched on and condensation checks are performed
*** Notice at time : 0.000000
Generated by Unit : 56
Generated by Type : 56
Message : Star network calculation: every iteration step of TRNSYS
*** The TRNSYS components will be called in the following order:
Unit # 15 Type # 15
Unit # 200 Type # 2
Unit # 56 Type # 56
Unit # 13 Type # 62
Unit # 16 Type # 62
Unit # 17 Type # 579
Unit # 18 Type # 579
Unit # 19 Type # 579
Unit # 25 Type # 65
Unit # 66 Type # 65
*TRACE* UNIT 56 TYPE 56 AT TIME 1.2130000000000000E+03 ITERATION 31 CALL 3565 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 7.0999999999999996E+00 7.4000000000000000E+01 -1.4306589791089372E+01 7.0999999999999996E+00 6.3730394255306038E+01
I -6.8329657628350668E+00 3.3151377628562193E+02 3.2509784377785995E+03 6.8134260815000482E+02 3.3151377628562193E+02
I 1.6344000000000001E+03 0.0000000000000000E+00 2.5834457374478920E+03 3.0956490634630313E+02 0.0000000000000000E+00
I 1.2842352784521684E+03 1.5291752864586689E+02 2.7082471354133101E+01 8.3875591558332502E+01 9.6124408441667512E+01
I 6.3730394255306038E+01 2.0000000000000001E-01 0.0000000000000000E+00 2.4099000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.3937051264436086E+01 -5.0359874325542910E+02 2.6026951329363879E+02 0.0000000000000000E+00 2.6026951329363879E+02
O 2.4099000000000000E+01 2.2000000000000000E+01
*TRACE* UNIT 56 TYPE 56 AT TIME 1.2130000000000000E+03 ITERATION 32 CALL 3566 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 7.0999999999999996E+00 7.4000000000000000E+01 -1.4306589791089372E+01 7.0999999999999996E+00 6.3730394255306038E+01
I -6.8329657628350668E+00 3.3151377628562193E+02 3.2509784377785995E+03 6.8134260815000482E+02 3.3151377628562193E+02
I 1.6344000000000001E+03 0.0000000000000000E+00 2.5834457374478920E+03 3.0956490634630313E+02 0.0000000000000000E+00
I 1.2842352784521684E+03 1.5291752864586689E+02 2.7082471354133101E+01 8.3875591558332502E+01 9.6124408441667512E+01
I 6.3730394255306038E+01 2.0000000000000001E-01 0.0000000000000000E+00 3.0000000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.4123685930766587E+01 -5.2747168193442269E+02 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 3.0000000000000000E+01 2.2000000000000000E+01
*** Warning at time : 1213.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 441 : The inputs to the listed units have not converged at this timestep. The values at the last iteration will be used and the simulation will proceed.
Reported information : UNITS: 56
*TRACE* UNIT 56 TYPE 56 AT TIME 1.2870000000000000E+03 ITERATION 31 CALL 3810 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 6.2000000000000002E+00 7.7000000000000000E+01 -1.1379298936575111E+01 6.2000000000000002E+00 6.5686470264069484E+01
I 2.5872472537558689E+01 3.3979301355608288E+02 2.5862478007281429E+03 3.3979301355608288E+02 1.4292793834837514E+03
I 1.3788000000000000E+03 0.0000000000000000E+00 1.9069073987962834E+03 0.0000000000000000E+00 9.2481256759148494E+02
I 9.5751827514718320E+02 1.4508115231859404E+02 3.4918847681405950E+01 1.1343236363240713E+02 6.6567636367592883E+01
I 6.5686470264069484E+01 2.0000000000000001E-01 0.0000000000000000E+00 2.3945000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.3828397743353989E+01 -4.8970058115591712E+02 2.5888365779452647E+02 0.0000000000000000E+00 2.5888365779452647E+02
O 2.3945000000000000E+01 2.2000000000000000E+01
*TRACE* UNIT 56 TYPE 56 AT TIME 1.2870000000000000E+03 ITERATION 32 CALL 3811 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 6.2000000000000002E+00 7.7000000000000000E+01 -1.1379298936575111E+01 6.2000000000000002E+00 6.5686470264069484E+01
I 2.5872472537558689E+01 3.3979301355608288E+02 2.5862478007281429E+03 3.3979301355608288E+02 1.4292793834837514E+03
I 1.3788000000000000E+03 0.0000000000000000E+00 1.9069073987962834E+03 0.0000000000000000E+00 9.2481256759148494E+02
I 9.5751827514718320E+02 1.4508115231859404E+02 3.4918847681405950E+01 1.1343236363240713E+02 6.6567636367592883E+01
I 6.5686470264069484E+01 2.0000000000000001E-01 0.0000000000000000E+00 3.0000000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.4014061527809321E+01 -5.1344933174099356E+02 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 3.0000000000000000E+01 2.2000000000000000E+01
*** Warning at time : 1287.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 441 : The inputs to the listed units have not converged at this timestep. The values at the last iteration will be used and the simulation will proceed.
Reported information : UNITS: 56
*TRACE* UNIT 56 TYPE 56 AT TIME 1.7650000000000000E+03 ITERATION 31 CALL 5237 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.0800000000000001E+01 6.7500000000000000E+01 -1.2620362343304915E+01 1.0800000000000001E+01 5.4909300608405061E+01
I -6.2847387366123861E+00 3.6079576061456623E+02 3.0236832684558563E+03 6.5406336965726473E+02 3.6079576061456623E+02
I 2.0304000000000001E+03 0.0000000000000000E+00 2.4214327567847708E+03 2.6667585203988421E+02 0.0000000000000000E+00
I 1.7115102203342249E+03 1.4442212861146973E+02 3.5577871388530262E+01 8.4860974495005038E+01 9.5139025504994962E+01
I 5.4909300608405061E+01 2.0000000000000001E-01 0.0000000000000000E+00 2.4209000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.4042683101418930E+01 -5.1711039367076660E+02 3.7932699758104610E+02 0.0000000000000000E+00 3.7932699758104610E+02
O 2.4209000000000000E+01 2.2000000000000000E+01
*TRACE* UNIT 56 TYPE 56 AT TIME 1.7650000000000000E+03 ITERATION 32 CALL 5238 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.0800000000000001E+01 6.7500000000000000E+01 -1.2620362343304915E+01 1.0800000000000001E+01 5.4909300608405061E+01
I -6.2847387366123861E+00 3.6079576061456623E+02 3.0236832684558563E+03 6.5406336965726473E+02 3.6079576061456623E+02
I 2.0304000000000001E+03 0.0000000000000000E+00 2.4214327567847708E+03 2.6667585203988421E+02 0.0000000000000000E+00
I 1.7115102203342249E+03 1.4442212861146973E+02 3.5577871388530262E+01 8.4860974495005038E+01 9.5139025504994962E+01
I 5.4909300608405061E+01 2.0000000000000001E-01 0.0000000000000000E+00 3.0000000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.4314736924847036E+01 -5.5190952489210019E+02 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 3.0000000000000000E+01 2.2000000000000000E+01
*** Warning at time : 1765.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 441 : The inputs to the listed units have not converged at this timestep. The values at the last iteration will be used and the simulation will proceed.
Reported information : UNITS: 56
*TRACE* UNIT 56 TYPE 56 AT TIME 2.0300000000000000E+03 ITERATION 31 CALL 6042 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.4600000000000000E+01 5.9000000000000000E+01 -1.2837004683984958E+01 1.4600000000000000E+01 5.1180954229645778E+01
I 1.3769754779504730E+01 3.8791659848441566E+02 2.9297317388425781E+03 3.8791659848441566E+02 1.0108237422726972E+03
I 2.2788000000000002E+03 0.0000000000000000E+00 2.3891716154056053E+03 0.0000000000000000E+00 5.8549972550821940E+02
I 1.9791313507622413E+03 1.3917742060814231E+02 4.0822579391857701E+01 1.0068731383031448E+02 7.9312686169685520E+01
I 5.1180954229645778E+01 2.0000000000000001E-01 0.0000000000000000E+00 2.4032999999999998E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.4027157789636568E+01 -5.1512450957195597E+02 3.4084676025525380E+02 0.0000000000000000E+00 3.4084676025525380E+02
O 2.4032999999999998E+01 2.2000000000000000E+01
*TRACE* UNIT 56 TYPE 56 AT TIME 2.0300000000000000E+03 ITERATION 32 CALL 6043 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.4600000000000000E+01 5.9000000000000000E+01 -1.2837004683984958E+01 1.4600000000000000E+01 5.1180954229645778E+01
I 1.3769754779504730E+01 3.8791659848441566E+02 2.9297317388425781E+03 3.8791659848441566E+02 1.0108237422726972E+03
I 2.2788000000000002E+03 0.0000000000000000E+00 2.3891716154056053E+03 0.0000000000000000E+00 5.8549972550821940E+02
I 1.9791313507622413E+03 1.3917742060814231E+02 4.0822579391857701E+01 1.0068731383031448E+02 7.9312686169685520E+01
I 5.1180954229645778E+01 2.0000000000000001E-01 0.0000000000000000E+00 3.0000000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.4271645661371537E+01 -5.4639760628246063E+02 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 3.0000000000000000E+01 2.2000000000000000E+01
*** Warning at time : 2030.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 441 : The inputs to the listed units have not converged at this timestep. The values at the last iteration will be used and the simulation will proceed.
Reported information : UNITS: 56
*TRACE* UNIT 56 TYPE 56 AT TIME 2.0530000000000000E+03 ITERATION 31 CALL 6142 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.4800000000000001E+01 6.2500000000000000E+01 -9.5047771581995022E+00 1.4800000000000001E+01 5.0128165120497705E+01
I -5.5067965458420822E+00 4.5175070539645895E+02 2.8435241532944665E+03 6.8233864517324218E+02 4.5175070539645895E+02
I 2.2500000000000000E+03 0.0000000000000000E+00 2.0296313299599726E+03 1.9567426308423506E+02 0.0000000000000000E+00
I 1.7032012468323740E+03 1.3981263256823257E+02 4.0187367431767413E+01 8.5776321146017352E+01 9.4223678853982648E+01
I 5.0128165120497705E+01 2.0000000000000001E-01 0.0000000000000000E+00 2.4253000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.4230475441889300E+01 -5.4113141354118477E+02 4.3465308591783526E+02 0.0000000000000000E+00 4.3465308591783526E+02
O 2.4253000000000000E+01 2.2000000000000000E+01
*TRACE* UNIT 56 TYPE 56 AT TIME 2.0530000000000000E+03 ITERATION 32 CALL 6143 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.4800000000000001E+01 6.2500000000000000E+01 -9.5047771581995022E+00 1.4800000000000001E+01 5.0128165120497705E+01
I -5.5067965458420822E+00 4.5175070539645895E+02 2.8435241532944665E+03 6.8233864517324218E+02 4.5175070539645895E+02
I 2.2500000000000000E+03 0.0000000000000000E+00 2.0296313299599726E+03 1.9567426308423506E+02 0.0000000000000000E+00
I 1.7032012468323740E+03 1.3981263256823257E+02 4.0187367431767413E+01 8.5776321146017352E+01 9.4223678853982648E+01
I 5.0128165120497705E+01 2.0000000000000001E-01 0.0000000000000000E+00 3.0000000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.4542258185403245E+01 -5.8101237704823268E+02 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 3.0000000000000000E+01 2.2000000000000000E+01
*** Warning at time : 2053.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 441 : The inputs to the listed units have not converged at this timestep. The values at the last iteration will be used and the simulation will proceed.
Reported information : UNITS: 56
*TRACE* UNIT 56 TYPE 56 AT TIME 3.0400000000000000E+03 ITERATION 31 CALL 9073 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 2.2300000000000001E+01 5.8000000000000000E+01 -5.5085246335635507E-01 2.2300000000000001E+01 4.9211962243215126E+01
I 6.0015864196797899E+01 4.9484804826473254E+02 1.5112814968251287E+03 4.9484804826473254E+02 2.2564886942475769E+03
I 2.1455999999999999E+03 0.0000000000000000E+00 8.1594761415228152E+02 0.0000000000000000E+00 1.4141668439967475E+03
I 1.4086953497117388E+03 1.1223362999943983E+02 6.7766370000560158E+01 1.3098032834544199E+02 4.9019671654557996E+01
I 4.9211962243215126E+01 2.0000000000000001E-01 0.0000000000000000E+00 2.5308999999999997E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.5297234851659628E+01 -6.7758345900196116E+02 7.9493816994796916E+01 0.0000000000000000E+00 7.9493816994796916E+01
O 2.5308999999999997E+01 2.2000000000000000E+01
*TRACE* UNIT 56 TYPE 56 AT TIME 3.0400000000000000E+03 ITERATION 32 CALL 9074 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 2.2300000000000001E+01 5.8000000000000000E+01 -5.5085246335635507E-01 2.2300000000000001E+01 4.9211962243215126E+01
I 6.0015864196797899E+01 4.9484804826473254E+02 1.5112814968251287E+03 4.9484804826473254E+02 2.2564886942475769E+03
I 2.1455999999999999E+03 0.0000000000000000E+00 8.1594761415228152E+02 0.0000000000000000E+00 1.4141668439967475E+03
I 1.4086953497117388E+03 1.1223362999943983E+02 6.7766370000560158E+01 1.3098032834544199E+02 4.9019671654557996E+01
I 4.9211962243215126E+01 2.0000000000000001E-01 0.0000000000000000E+00 3.0000000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.5354223988716480E+01 -6.8487309174316783E+02 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 3.0000000000000000E+01 2.2000000000000000E+01
*** Warning at time : 3040.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 441 : The inputs to the listed units have not converged at this timestep. The values at the last iteration will be used and the simulation will proceed.
Reported information : UNITS: 56
*TRACE* UNIT 56 TYPE 56 AT TIME 3.5880000000000000E+03 ITERATION 31 CALL 10724 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.6600000000000001E+01 5.6500000000000000E+01 -4.3785293961235174E+00 1.6600000000000001E+01 3.3338233443817572E+01
I -2.9668101815869164E+01 4.8662753123344811E+02 2.1098709128017254E+03 1.4113118681938327E+03 4.8662753123344811E+02
I 3.0132000000000003E+03 0.0000000000000000E+00 1.4389066565712922E+03 8.1967649632061273E+02 0.0000000000000000E+00
I 2.5173502567291644E+03 1.1852449328481146E+02 6.1475506715188544E+01 7.4214985506429230E+01 1.0578501449357077E+02
I 3.3338233443817572E+01 2.0000000000000001E-01 0.0000000000000000E+00 2.5111000000000001E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.4993299079509395E+01 -6.3870622256162005E+02 3.3981603639632283E+02 0.0000000000000000E+00 3.3981603639632283E+02
O 2.5111000000000001E+01 2.2000000000000000E+01
*TRACE* UNIT 56 TYPE 56 AT TIME 3.5880000000000000E+03 ITERATION 32 CALL 10725 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.6600000000000001E+01 5.6500000000000000E+01 -4.3785293961235174E+00 1.6600000000000001E+01 3.3338233443817572E+01
I -2.9668101815869164E+01 4.8662753123344811E+02 2.1098709128017254E+03 1.4113118681938327E+03 4.8662753123344811E+02
I 3.0132000000000003E+03 0.0000000000000000E+00 1.4389066565712922E+03 8.1967649632061273E+02 0.0000000000000000E+00
I 2.5173502567291644E+03 1.1852449328481146E+02 6.1475506715188544E+01 7.4214985506429230E+01 1.0578501449357077E+02
I 3.3338233443817572E+01 2.0000000000000001E-01 0.0000000000000000E+00 3.0000000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.5237091538903041E+01 -6.6989036722207209E+02 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 3.0000000000000000E+01 2.2000000000000000E+01
*** Warning at time : 3588.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 441 : The inputs to the listed units have not converged at this timestep. The values at the last iteration will be used and the simulation will proceed.
Reported information : UNITS: 56
*TRACE* UNIT 56 TYPE 56 AT TIME 3.6120000000000000E+03 ITERATION 31 CALL 10827 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.6600000000000001E+01 5.5500000000000000E+01 -1.5524332753996526E+00 1.6600000000000001E+01 3.3206008477354942E+01
I -2.9813068367734544E+01 5.1780306555437687E+02 2.0836391145734674E+03 1.4150401742038721E+03 5.1780306555437687E+02
I 2.9915999999999999E+03 0.0000000000000000E+00 1.3582273633745770E+03 7.7827560118203348E+02 0.0000000000000000E+00
I 2.3916429662441860E+03 1.1837045198593042E+02 6.1629548014069591E+01 7.4200213670484501E+01 1.0579978632951550E+02
I 3.3206008477354942E+01 2.0000000000000001E-01 0.0000000000000000E+00 2.5023000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.4935297440580996E+01 -6.3128707800159088E+02 4.6350650902239897E+02 0.0000000000000000E+00 4.6350650902239897E+02
O 2.5023000000000000E+01 2.2000000000000000E+01
*TRACE* UNIT 56 TYPE 56 AT TIME 3.6120000000000000E+03 ITERATION 32 CALL 10828 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.6600000000000001E+01 5.5500000000000000E+01 -1.5524332753996526E+00 1.6600000000000001E+01 3.3206008477354942E+01
I -2.9813068367734544E+01 5.1780306555437687E+02 2.0836391145734674E+03 1.4150401742038721E+03 5.1780306555437687E+02
I 2.9915999999999999E+03 0.0000000000000000E+00 1.3582273633745770E+03 7.7827560118203348E+02 0.0000000000000000E+00
I 2.3916429662441860E+03 1.1837045198593042E+02 6.1629548014069591E+01 7.4200213670484501E+01 1.0579978632951550E+02
I 3.3206008477354942E+01 2.0000000000000001E-01 0.0000000000000000E+00 3.0000000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.5267829687407485E+01 -6.7382216590009966E+02 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 3.0000000000000000E+01 2.2000000000000000E+01
*** Warning at time : 3612.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 441 : The inputs to the listed units have not converged at this timestep. The values at the last iteration will be used and the simulation will proceed.
Reported information : UNITS: 56
*TRACE* UNIT 56 TYPE 56 AT TIME 3.9740000000000000E+03 ITERATION 31 CALL 11920 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.8600000000000001E+01 6.6000000000000000E+01 4.8273547886736896E+00 1.8600000000000001E+01 3.0493389956841611E+01
I 2.2607726564295916E+01 6.2613273521865665E+02 1.7587416013826371E+03 6.2613273521865665E+02 1.0977715146501375E+03
I 2.6028000000000002E+03 0.0000000000000000E+00 7.6562900386867682E+02 0.0000000000000000E+00 3.1882173949862295E+02
I 1.4083423897824462E+03 1.1793350441411280E+02 6.2066495585887203E+01 1.0124878893130845E+02 7.8751211068691546E+01
I 3.0493389956841611E+01 2.0000000000000001E-01 0.0000000000000000E+00 2.4902000000000001E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.4830757932398349E+01 -6.1791515028074059E+02 1.7890616373117848E+02 0.0000000000000000E+00 1.7890616373117848E+02
O 2.4902000000000001E+01 2.2000000000000000E+01
*TRACE* UNIT 56 TYPE 56 AT TIME 3.9740000000000000E+03 ITERATION 32 CALL 11921 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.8600000000000001E+01 6.6000000000000000E+01 4.8273547886736896E+00 1.8600000000000001E+01 3.0493389956841611E+01
I 2.2607726564295916E+01 6.2613273521865665E+02 1.7587416013826371E+03 6.2613273521865665E+02 1.0977715146501375E+03
I 2.6028000000000002E+03 0.0000000000000000E+00 7.6562900386867682E+02 0.0000000000000000E+00 3.1882173949862295E+02
I 1.4083423897824462E+03 1.1793350441411280E+02 6.2066495585887203E+01 1.0124878893130845E+02 7.8751211068691546E+01
I 3.0493389956841611E+01 2.0000000000000001E-01 0.0000000000000000E+00 3.0000000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.4959020526369354E+01 -6.3432156127009091E+02 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 3.0000000000000000E+01 2.2000000000000000E+01
*** Warning at time : 3974.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 441 : The inputs to the listed units have not converged at this timestep. The values at the last iteration will be used and the simulation will proceed.
Reported information : UNITS: 56
*TRACE* UNIT 56 TYPE 56 AT TIME 4.1170000000000000E+03 ITERATION 31 CALL 12372 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.2100000000000000E+01 5.9500000000000000E+01 6.1159594142028055E+00 1.2100000000000000E+01 2.8943079969948570E+01
I -5.8165389002514161E+00 5.0529569472443791E+02 2.1329971642367159E+03 6.7110629189320537E+02 5.0529569472443791E+02
I 3.1428000000000002E+03 0.0000000000000000E+00 1.4264368838364883E+03 1.4530818824127127E+02 0.0000000000000000E+00
I 2.5927489633323339E+03 1.1878007661218101E+02 6.1219923387818987E+01 8.7188845972259415E+01 9.2811154027740585E+01
I 2.8943079969948570E+01 2.0000000000000001E-01 0.0000000000000000E+00 2.4759000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.4645085727930905E+01 -5.9416532266942477E+02 1.6205357017384691E+02 0.0000000000000000E+00 1.6205357017384691E+02
O 2.4759000000000000E+01 2.2000000000000000E+01
*TRACE* UNIT 56 TYPE 56 AT TIME 4.1170000000000000E+03 ITERATION 32 CALL 12373 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.2100000000000000E+01 5.9500000000000000E+01 6.1159594142028055E+00 1.2100000000000000E+01 2.8943079969948570E+01
I -5.8165389002514161E+00 5.0529569472443791E+02 2.1329971642367159E+03 6.7110629189320537E+02 5.0529569472443791E+02
I 3.1428000000000002E+03 0.0000000000000000E+00 1.4264368838364883E+03 1.4530818824127127E+02 0.0000000000000000E+00
I 2.5927489633323339E+03 1.1878007661218101E+02 6.1219923387818987E+01 8.7188845972259415E+01 9.2811154027740585E+01
I 2.8943079969948570E+01 2.0000000000000001E-01 0.0000000000000000E+00 3.0000000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.4761343730544851E+01 -6.0903619431355003E+02 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 3.0000000000000000E+01 2.2000000000000000E+01
*** Warning at time : 4117.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 441 : The inputs to the listed units have not converged at this timestep. The values at the last iteration will be used and the simulation will proceed.
Reported information : UNITS: 56
*TRACE* UNIT 56 TYPE 56 AT TIME 4.2140000000000000E+03 ITERATION 31 CALL 12688 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.3600000000000000E+01 5.2500000000000000E+01 6.1764688078936061E+00 1.3600000000000000E+01 3.0233494349767195E+01
I 2.1719699562854949E+01 5.8375414650673110E+02 1.9634912850776548E+03 5.8375414650673110E+02 1.1333678241175428E+03
I 2.8980000000000000E+03 0.0000000000000000E+00 1.0592354514383371E+03 0.0000000000000000E+00 4.2194290176443423E+02
I 1.9563976605145574E+03 1.1789012800367145E+02 6.2109871996328550E+01 1.0073912842436407E+02 7.9260871575635932E+01
I 3.0233494349767195E+01 2.0000000000000001E-01 0.0000000000000000E+00 2.4770000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.4754373513297828E+01 -6.0814461520775421E+02 9.4829361920282594E+01 0.0000000000000000E+00 9.4829361920282594E+01
O 2.4770000000000000E+01 2.2000000000000000E+01
*TRACE* UNIT 56 TYPE 56 AT TIME 4.2140000000000000E+03 ITERATION 32 CALL 12689 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.3600000000000000E+01 5.2500000000000000E+01 6.1764688078936061E+00 1.3600000000000000E+01 3.0233494349767195E+01
I 2.1719699562854949E+01 5.8375414650673110E+02 1.9634912850776548E+03 5.8375414650673110E+02 1.1333678241175428E+03
I 2.8980000000000000E+03 0.0000000000000000E+00 1.0592354514383371E+03 0.0000000000000000E+00 4.2194290176443423E+02
I 1.9563976605145574E+03 1.1789012800367145E+02 6.2109871996328550E+01 1.0073912842436407E+02 7.9260871575635932E+01
I 3.0233494349767195E+01 2.0000000000000001E-01 0.0000000000000000E+00 3.0000000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.4822409656842925E+01 -6.1684730005586846E+02 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 3.0000000000000000E+01 2.2000000000000000E+01
*** Warning at time : 4214.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 441 : The inputs to the listed units have not converged at this timestep. The values at the last iteration will be used and the simulation will proceed.
Reported information : UNITS: 56
*TRACE* UNIT 56 TYPE 56 AT TIME 4.2390000000000000E+03 ITERATION 31 CALL 12795 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 2.1399999999999999E+01 5.5500000000000000E+01 8.1678206804715767E+00 2.1399999999999999E+01 3.5334439490129931E+01
I 4.5404378745197164E+01 6.4682055128977629E+02 1.3969999085221789E+03 6.4682055128977629E+02 1.4076644959945190E+03
I 2.2284000000000001E+03 0.0000000000000000E+00 4.5608367388069996E+02 0.0000000000000000E+00 4.6256738232710575E+02
I 9.1629544319860770E+02 1.1395740637421085E+02 6.6042593625789138E+01 1.1431984036711974E+02 6.5680159632880276E+01
I 3.5334439490129931E+01 2.0000000000000001E-01 0.0000000000000000E+00 3.0000000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.5004569036626041E+01 -6.4014779287891656E+02 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 3.0000000000000000E+01 2.2000000000000000E+01
*TRACE* UNIT 56 TYPE 56 AT TIME 4.2390000000000000E+03 ITERATION 32 CALL 12796 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 2.1399999999999999E+01 5.5500000000000000E+01 8.1678206804715767E+00 2.1399999999999999E+01 3.5334439490129931E+01
I 4.5404378745197164E+01 6.4682055128977629E+02 1.3969999085221789E+03 6.4682055128977629E+02 1.4076644959945190E+03
I 2.2284000000000001E+03 0.0000000000000000E+00 4.5608367388069996E+02 0.0000000000000000E+00 4.6256738232710575E+02
I 9.1629544319860770E+02 1.1395740637421085E+02 6.6042593625789138E+01 1.1431984036711974E+02 6.5680159632880276E+01
I 3.5334439490129931E+01 2.0000000000000001E-01 0.0000000000000000E+00 2.4913000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.4895788853663518E+01 -6.2623342911996031E+02 1.5173599448745873E+02 0.0000000000000000E+00 1.5173599448745873E+02
O 2.4913000000000000E+01 2.2000000000000000E+01
*** Warning at time : 4239.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 441 : The inputs to the listed units have not converged at this timestep. The values at the last iteration will be used and the simulation will proceed.
Reported information : UNITS: 56
*TRACE* UNIT 56 TYPE 56 AT TIME 4.3830000000000000E+03 ITERATION 31 CALL 13243 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.9800000000000001E+01 7.0000000000000000E+01 8.4896918861507071E+00 1.9800000000000001E+01 3.5453999076523544E+01
I 4.4733627029458574E+01 6.2979434551288080E+02 1.0708764783585630E+03 6.2979434551288080E+02 1.0667941709571712E+03
I 1.7388000000000000E+03 0.0000000000000000E+00 1.8691000571999768E+02 0.0000000000000000E+00 1.8518011452077317E+02
I 3.6949416091167632E+02 1.1433424975573888E+02 6.5665750244261119E+01 1.1409466128360751E+02 6.5905338716392478E+01
I 3.5453999076523544E+01 2.0000000000000001E-01 0.0000000000000000E+00 2.5111000000000001E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.5094105448597276E+01 -6.5160063448949495E+02 6.1124114432204422E+01 0.0000000000000000E+00 6.1124114432204422E+01
O 2.5111000000000001E+01 2.2000000000000000E+01
*TRACE* UNIT 56 TYPE 56 AT TIME 4.3830000000000000E+03 ITERATION 32 CALL 13244 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.9800000000000001E+01 7.0000000000000000E+01 8.4896918861507071E+00 1.9800000000000001E+01 3.5453999076523544E+01
I 4.4733627029458574E+01 6.2979434551288080E+02 1.0708764783585630E+03 6.2979434551288080E+02 1.0667941709571712E+03
I 1.7388000000000000E+03 0.0000000000000000E+00 1.8691000571999768E+02 0.0000000000000000E+00 1.8518011452077317E+02
I 3.6949416091167632E+02 1.1433424975573888E+02 6.5665750244261119E+01 1.1409466128360751E+02 6.5905338716392478E+01
I 3.5453999076523544E+01 2.0000000000000001E-01 0.0000000000000000E+00 3.0000000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.5137927066914191E+01 -6.5720597473770704E+02 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 3.0000000000000000E+01 2.2000000000000000E+01
*** Warning at time : 4383.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 441 : The inputs to the listed units have not converged at this timestep. The values at the last iteration will be used and the simulation will proceed.
Reported information : UNITS: 56
*TRACE* UNIT 56 TYPE 56 AT TIME 4.5720000000000000E+03 ITERATION 31 CALL 13829 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.7100000000000001E+01 7.2000000000000000E+01 5.0581018872199603E+00 1.7100000000000001E+01 3.3318290208980535E+01
I -3.3254629712442949E+01 5.8549885491310522E+02 1.8219719205887266E+03 1.3963089856413330E+03 5.8549885491310522E+02
I 2.6712000000000003E+03 0.0000000000000000E+00 9.3429542594946724E+02 6.1265887424644188E+02 0.0000000000000000E+00
I 1.6996756045954733E+03 1.1734445942965199E+02 6.2655540570347988E+01 7.2469773909157780E+01 1.0753022609084222E+02
I 3.3318290208980535E+01 2.0000000000000001E-01 0.0000000000000000E+00 2.5132999999999999E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.5127328845993766E+01 -6.5585032799150349E+02 5.4003204583163756E+02 0.0000000000000000E+00 5.4003204583163756E+02
O 2.5132999999999999E+01 2.2000000000000000E+01
*TRACE* UNIT 56 TYPE 56 AT TIME 4.5720000000000000E+03 ITERATION 32 CALL 13830 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.7100000000000001E+01 7.2000000000000000E+01 5.0581018872199603E+00 1.7100000000000001E+01 3.3318290208980535E+01
I -3.3254629712442949E+01 5.8549885491310522E+02 1.8219719205887266E+03 1.3963089856413330E+03 5.8549885491310522E+02
I 2.6712000000000003E+03 0.0000000000000000E+00 9.3429542594946724E+02 6.1265887424644188E+02 0.0000000000000000E+00
I 1.6996756045954733E+03 1.1734445942965199E+02 6.2655540570347988E+01 7.2469773909157780E+01 1.0753022609084222E+02
I 3.3318290208980535E+01 2.0000000000000001E-01 0.0000000000000000E+00 3.0000000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.5514500251764293E+01 -7.0537445665392318E+02 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 3.0000000000000000E+01 2.2000000000000000E+01
*** Warning at time : 4572.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 441 : The inputs to the listed units have not converged at this timestep. The values at the last iteration will be used and the simulation will proceed.
Reported information : UNITS: 56
*TRACE* UNIT 56 TYPE 56 AT TIME 4.7650000000000000E+03 ITERATION 31 CALL 14434 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.9699999999999999E+01 8.4000000000000000E+01 1.0682465732522717E+01 1.9699999999999999E+01 3.1296948818702802E+01
I -7.6634456456560320E+00 6.5687784762269177E+02 1.0716188072704088E+03 7.1268360939463025E+02 6.5687784762269177E+02
I 1.6956000000000008E+03 0.0000000000000000E+00 1.7051299423359737E+02 2.2943495967465228E+01 0.0000000000000000E+00
I 2.8300592712924606E+02 1.2098635460064691E+02 5.9013645399353095E+01 8.6027719906628732E+01 9.3972280093371268E+01
I 3.1296948818702802E+01 2.0000000000000001E-01 0.0000000000000000E+00 2.5265000000000001E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.5144189824032161E+01 -6.5800706072874129E+02 1.8021461163507905E+02 0.0000000000000000E+00 1.8021461163507905E+02
O 2.5265000000000001E+01 2.2000000000000000E+01
*TRACE* UNIT 56 TYPE 56 AT TIME 4.7650000000000000E+03 ITERATION 32 CALL 14435 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.9699999999999999E+01 8.4000000000000000E+01 1.0682465732522717E+01 1.9699999999999999E+01 3.1296948818702802E+01
I -7.6634456456560320E+00 6.5687784762269177E+02 1.0716188072704088E+03 7.1268360939463025E+02 6.5687784762269177E+02
I 1.6956000000000008E+03 0.0000000000000000E+00 1.7051299423359737E+02 2.2943495967465228E+01 0.0000000000000000E+00
I 2.8300592712924606E+02 1.2098635460064691E+02 5.9013645399353095E+01 8.6027719906628732E+01 9.3972280093371268E+01
I 3.1296948818702802E+01 2.0000000000000001E-01 0.0000000000000000E+00 3.0000000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.5273391021279185E+01 -6.7453353097017407E+02 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 3.0000000000000000E+01 2.2000000000000000E+01
*** Warning at time : 4765.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 441 : The inputs to the listed units have not converged at this timestep. The values at the last iteration will be used and the simulation will proceed.
Reported information : UNITS: 56
*TRACE* UNIT 56 TYPE 56 AT TIME 4.9090000000000000E+03 ITERATION 31 CALL 14892 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 2.2100000000000001E+01 7.3000000000000000E+01 1.1116238401427445E+01 2.2100000000000001E+01 3.2434265355761184E+01
I -7.6566955908193002E+00 6.7127651684136583E+02 1.4275755494953382E+03 7.7295015371241550E+02 6.7127651684136583E+02
I 2.0772000000000003E+03 0.0000000000000000E+00 4.2290102846246936E+02 5.6853022076995394E+01 0.0000000000000000E+00
I 6.7149222929688335E+02 1.2211022913762793E+02 5.7889770862372075E+01 8.5902190897431936E+01 9.4097809102568064E+01
I 3.2434265355761184E+01 2.0000000000000001E-01 0.0000000000000000E+00 2.5265000000000001E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.5190081273197414E+01 -6.6387715856936529E+02 1.3115158406254588E+02 0.0000000000000000E+00 1.3115158406254588E+02
O 2.5265000000000001E+01 2.2000000000000000E+01
*TRACE* UNIT 56 TYPE 56 AT TIME 4.9090000000000000E+03 ITERATION 32 CALL 14893 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 2.2100000000000001E+01 7.3000000000000000E+01 1.1116238401427445E+01 2.2100000000000001E+01 3.2434265355761184E+01
I -7.6566955908193002E+00 6.7127651684136583E+02 1.4275755494953382E+03 7.7295015371241550E+02 6.7127651684136583E+02
I 2.0772000000000003E+03 0.0000000000000000E+00 4.2290102846246936E+02 5.6853022076995394E+01 0.0000000000000000E+00
I 6.7149222929688335E+02 1.2211022913762793E+02 5.7889770862372075E+01 8.5902190897431936E+01 9.4097809102568064E+01
I 3.2434265355761184E+01 2.0000000000000001E-01 0.0000000000000000E+00 3.0000000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.5284102905119095E+01 -6.7590371664400720E+02 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 3.0000000000000000E+01 2.2000000000000000E+01
*** Warning at time : 4909.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 441 : The inputs to the listed units have not converged at this timestep. The values at the last iteration will be used and the simulation will proceed.
Reported information : UNITS: 56
*TRACE* UNIT 56 TYPE 56 AT TIME 5.0780000000000000E+03 ITERATION 31 CALL 15413 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.7199999999999999E+01 6.5500000000000000E+01 1.4913876171165537E+01 1.7199999999999999E+01 3.4841884937371290E+01
I 1.7832520270114362E+01 6.5409759353814229E+02 1.3579881131334082E+03 6.5409759353814229E+02 8.8053289762283919E+02
I 1.9368000000000000E+03 0.0000000000000000E+00 3.6417223893302656E+02 0.0000000000000000E+00 1.1715096221131056E+02
I 5.4956200054540773E+02 1.2294715973766675E+02 5.7052840262333227E+01 1.0007613449266915E+02 7.9923865507330845E+01
I 3.4841884937371290E+01 2.0000000000000001E-01 0.0000000000000000E+00 3.0000000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.5206178065606352E+01 -6.6593614228156889E+02 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 3.0000000000000000E+01 2.2000000000000000E+01
*TRACE* UNIT 56 TYPE 56 AT TIME 5.0780000000000000E+03 ITERATION 32 CALL 15414 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.7199999999999999E+01 6.5500000000000000E+01 1.4913876171165537E+01 1.7199999999999999E+01 3.4841884937371290E+01
I 1.7832520270114362E+01 6.5409759353814229E+02 1.3579881131334082E+03 6.5409759353814229E+02 8.8053289762283919E+02
I 1.9368000000000000E+03 0.0000000000000000E+00 3.6417223893302656E+02 0.0000000000000000E+00 1.1715096221131056E+02
I 5.4956200054540773E+02 1.2294715973766675E+02 5.7052840262333227E+01 1.0007613449266915E+02 7.9923865507330845E+01
I 3.4841884937371290E+01 2.0000000000000001E-01 0.0000000000000000E+00 2.5187999999999999E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.5109183218514456E+01 -6.5352927231292813E+02 1.3528966740237288E+02 0.0000000000000000E+00 1.3528966740237288E+02
O 2.5187999999999999E+01 2.2000000000000000E+01
*** Warning at time : 5078.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 441 : The inputs to the listed units have not converged at this timestep. The values at the last iteration will be used and the simulation will proceed.
Reported information : UNITS: 56
*TRACE* UNIT 56 TYPE 56 AT TIME 5.1270000000000000E+03 ITERATION 31 CALL 15590 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 2.9800000000000001E+01 7.3000000000000000E+01 8.6749092280465359E+00 2.9800000000000001E+01 3.9780209856458526E+01
I 4.0055466369143950E+01 6.0877044640956115E+02 1.2061119575693658E+03 6.0877044640956115E+02 1.1109857106605027E+03
I 1.7640000000000000E+03 0.0000000000000000E+00 3.1912161090153234E+02 0.0000000000000000E+00 2.6830170204632464E+02
I 5.0075758020688653E+02 1.1932420265282934E+02 6.0675797347170658E+01 1.1431533581166340E+02 6.5684664188336612E+01
I 3.9780209856458526E+01 2.0000000000000001E-01 0.0000000000000000E+00 2.5738000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.5652232963526195E+01 -7.2299221570497059E+02 2.3325345266782898E+02 0.0000000000000000E+00 2.3325345266782898E+02
O 2.5738000000000000E+01 2.2000000000000000E+01
*TRACE* UNIT 56 TYPE 56 AT TIME 5.1270000000000000E+03 ITERATION 32 CALL 15591 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 2.9800000000000001E+01 7.3000000000000000E+01 8.6749092280465359E+00 2.9800000000000001E+01 3.9780209856458526E+01
I 4.0055466369143950E+01 6.0877044640956115E+02 1.2061119575693658E+03 6.0877044640956115E+02 1.1109857106605027E+03
I 1.7640000000000000E+03 0.0000000000000000E+00 3.1912161090153234E+02 0.0000000000000000E+00 2.6830170204632464E+02
I 5.0075758020688653E+02 1.1932420265282934E+02 6.0675797347170658E+01 1.1431533581166340E+02 6.5684664188336612E+01
I 3.9780209856458526E+01 2.0000000000000001E-01 0.0000000000000000E+00 3.0000000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.5819433813007766E+01 -7.4437932296231531E+02 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 3.0000000000000000E+01 2.2000000000000000E+01
*** Warning at time : 5127.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 441 : The inputs to the listed units have not converged at this timestep. The values at the last iteration will be used and the simulation will proceed.
Reported information : UNITS: 56
*TRACE* UNIT 56 TYPE 56 AT TIME 5.2200000000000000E+03 ITERATION 31 CALL 15898 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 2.2500000000000000E+01 7.3000000000000000E+01 2.4055043524224091E+00 2.2500000000000000E+01 3.8505135305644359E+01
I -3.0481924718567310E+01 6.2418781284032536E+02 1.6132151047816672E+03 1.2063492168373614E+03 6.2418781284032536E+02
I 2.1420000000000000E+03 0.0000000000000000E+00 6.2388505807095760E+02 3.6723132344147899E+02 0.0000000000000000E+00
I 9.0995188301317239E+02 1.2244819745959545E+02 5.7551802540404552E+01 7.1589893153436250E+01 1.0841010684656375E+02
I 3.8505135305644359E+01 2.0000000000000001E-01 0.0000000000000000E+00 2.5649999999999999E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.5607966000232430E+01 -7.1732991019123540E+02 5.4806355065209198E+02 0.0000000000000000E+00 5.4806355065209198E+02
O 2.5649999999999999E+01 2.2000000000000000E+01
*TRACE* UNIT 56 TYPE 56 AT TIME 5.2200000000000000E+03 ITERATION 32 CALL 15899 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 2.2500000000000000E+01 7.3000000000000000E+01 2.4055043524224091E+00 2.2500000000000000E+01 3.8505135305644359E+01
I -3.0481924718567310E+01 6.2418781284032536E+02 1.6132151047816672E+03 1.2063492168373614E+03 6.2418781284032536E+02
I 2.1420000000000000E+03 0.0000000000000000E+00 6.2388505807095760E+02 3.6723132344147899E+02 0.0000000000000000E+00
I 9.0995188301317239E+02 1.2244819745959545E+02 5.7551802540404552E+01 7.1589893153436250E+01 1.0841010684656375E+02
I 3.8505135305644359E+01 2.0000000000000001E-01 0.0000000000000000E+00 3.0000000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.6000869899261286E+01 -7.6758729737804686E+02 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 3.0000000000000000E+01 2.2000000000000000E+01
*** Warning at time : 5220.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 441 : The inputs to the listed units have not converged at this timestep. The values at the last iteration will be used and the simulation will proceed.
Reported information : UNITS: 56
*TRACE* UNIT 56 TYPE 56 AT TIME 5.2440000000000000E+03 ITERATION 31 CALL 16001 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 2.0199999999999999E+01 7.8000000000000000E+01 -1.6387655708461721E-01 2.0199999999999999E+01 3.8756887352783835E+01
I -3.0303414689730197E+01 5.6440721108881337E+02 1.9395545573543263E+03 1.3680883837329800E+03 5.6440721108881337E+02
I 2.4264000000000001E+03 0.0000000000000000E+00 1.0312389954304283E+03 6.0268986256247842E+02 0.0000000000000000E+00
I 1.4878760243609224E+03 1.2271643312700056E+02 5.7283566872999437E+01 7.1586343705179814E+01 1.0841365629482019E+02
I 3.8756887352783835E+01 2.0000000000000001E-01 0.0000000000000000E+00 2.5573000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.5566213545192802E+01 -7.1198924214463909E+02 8.6985984162180353E+02 0.0000000000000000E+00 8.6985984162180353E+02
O 2.5573000000000000E+01 2.2000000000000000E+01
*TRACE* UNIT 56 TYPE 56 AT TIME 5.2440000000000000E+03 ITERATION 32 CALL 16002 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 2.0199999999999999E+01 7.8000000000000000E+01 -1.6387655708461721E-01 2.0199999999999999E+01 3.8756887352783835E+01
I -3.0303414689730197E+01 5.6440721108881337E+02 1.9395545573543263E+03 1.3680883837329800E+03 5.6440721108881337E+02
I 2.4264000000000001E+03 0.0000000000000000E+00 1.0312389954304283E+03 6.0268986256247842E+02 0.0000000000000000E+00
I 1.4878760243609224E+03 1.2271643312700056E+02 5.7283566872999437E+01 7.1586343705179814E+01 1.0841365629482019E+02
I 3.8756887352783835E+01 2.0000000000000001E-01 0.0000000000000000E+00 3.0000000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.6189826975834272E+01 -7.9175730175440731E+02 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 3.0000000000000000E+01 2.2000000000000000E+01
*** Warning at time : 5244.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 441 : The inputs to the listed units have not converged at this timestep. The values at the last iteration will be used and the simulation will proceed.
Reported information : UNITS: 56
*TRACE* UNIT 56 TYPE 56 AT TIME 5.4610000000000000E+03 ITERATION 31 CALL 16666 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.8100000000000001E+01 8.0500000000000000E+01 8.7281202588165971E+00 1.8100000000000001E+01 3.8437873112475664E+01
I -6.1029285784965781E+00 6.3739522465524249E+02 1.7414543305347695E+03 7.5544218250892391E+02 6.3739522465524249E+02
I 2.1276000000000004E+03 0.0000000000000000E+00 6.6091784443937718E+02 7.0665909562086881E+01 0.0000000000000000E+00
I 8.3748586383733709E+02 1.2818060855721501E+02 5.1819391442784998E+01 8.6210426596391173E+01 9.3789573403608827E+01
I 3.8437873112475664E+01 2.0000000000000001E-01 0.0000000000000000E+00 2.5297999999999998E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.4999871840482697E+01 -6.3954696197382270E+02 5.6694455966399937E+02 0.0000000000000000E+00 5.6694455966399937E+02
O 2.5297999999999998E+01 2.2000000000000000E+01
*TRACE* UNIT 56 TYPE 56 AT TIME 5.4610000000000000E+03 ITERATION 32 CALL 16667 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.8100000000000001E+01 8.0500000000000000E+01 8.7281202588165971E+00 1.8100000000000001E+01 3.8437873112475664E+01
I -6.1029285784965781E+00 6.3739522465524249E+02 1.7414543305347695E+03 7.5544218250892391E+02 6.3739522465524249E+02
I 2.1276000000000004E+03 0.0000000000000000E+00 6.6091784443937718E+02 7.0665909562086881E+01 0.0000000000000000E+00
I 8.3748586383733709E+02 1.2818060855721501E+02 5.1819391442784998E+01 8.6210426596391173E+01 9.3789573403608827E+01
I 3.8437873112475664E+01 2.0000000000000001E-01 0.0000000000000000E+00 3.0000000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.5406331504874668E+01 -6.9153830331622157E+02 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 3.0000000000000000E+01 2.2000000000000000E+01
*** Warning at time : 5461.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 441 : The inputs to the listed units have not converged at this timestep. The values at the last iteration will be used and the simulation will proceed.
Reported information : UNITS: 56
*TRACE* UNIT 56 TYPE 56 AT TIME 5.4840000000000000E+03 ITERATION 31 CALL 16760 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.8000000000000000E+01 7.2500000000000000E+01 1.4736010987380929E+01 1.8000000000000000E+01 4.1465137247284972E+01
I -2.8308157194352582E+01 5.9994582712134968E+02 1.0860598742507141E+03 8.6178055339744856E+02 5.9994582712134968E+02
I 1.5552000000000000E+03 0.0000000000000000E+00 2.2875973952224516E+02 1.2321644300243587E+02 0.0000000000000000E+00
I 2.9404837994374680E+02 1.2566012430949306E+02 5.4339875690506929E+01 7.1699107501576563E+01 1.0830089249842344E+02
I 4.1465137247284972E+01 2.0000000000000001E-01 0.0000000000000000E+00 2.5308999999999997E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.5279356464810590E+01 -6.7529658678621433E+02 5.9565262216553855E+01 0.0000000000000000E+00 5.9565262216553855E+01
O 2.5308999999999997E+01 2.2000000000000000E+01
*TRACE* UNIT 56 TYPE 56 AT TIME 5.4840000000000000E+03 ITERATION 32 CALL 16761 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.8000000000000000E+01 7.2500000000000000E+01 1.4736010987380929E+01 1.8000000000000000E+01 4.1465137247284972E+01
I -2.8308157194352582E+01 5.9994582712134968E+02 1.0860598742507141E+03 8.6178055339744856E+02 5.9994582712134968E+02
I 1.5552000000000000E+03 0.0000000000000000E+00 2.2875973952224516E+02 1.2321644300243587E+02 0.0000000000000000E+00
I 2.9404837994374680E+02 1.2566012430949306E+02 5.4339875690506929E+01 7.1699107501576563E+01 1.0830089249842344E+02
I 4.1465137247284972E+01 2.0000000000000001E-01 0.0000000000000000E+00 3.0000000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.5322061135966830E+01 -6.8075905533969387E+02 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 3.0000000000000000E+01 2.2000000000000000E+01
*** Warning at time : 5484.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 441 : The inputs to the listed units have not converged at this timestep. The values at the last iteration will be used and the simulation will proceed.
Reported information : UNITS: 56
*TRACE* UNIT 56 TYPE 56 AT TIME 5.5550000000000000E+03 ITERATION 31 CALL 16995 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.5000000000000000E+01 7.3000000000000000E+01 6.9858892432400665E+00 1.5000000000000000E+01 4.7899226612183057E+01
I -4.6822644133865452E+01 4.7193939633826801E+02 1.8218688500424494E+03 1.9106072476628399E+03 4.7193939633826801E+02
I 2.0915999999999999E+03 0.0000000000000000E+00 1.0838324524288516E+03 1.1550788089355601E+03 0.0000000000000000E+00
I 1.4312481267097157E+03 1.2051057740240391E+02 5.9489422597596089E+01 5.7243409761885879E+01 1.2275659023811413E+02
I 4.7899226612183057E+01 2.0000000000000001E-01 0.0000000000000000E+00 2.5111000000000001E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.5104733164801232E+01 -6.5296005405619803E+02 5.6506733189756960E+02 0.0000000000000000E+00 5.6506733189756960E+02
O 2.5111000000000001E+01 2.2000000000000000E+01
*TRACE* UNIT 56 TYPE 56 AT TIME 5.5550000000000000E+03 ITERATION 32 CALL 16996 ITERATIVE CALL
P 3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
I 1.5000000000000000E+01 7.3000000000000000E+01 6.9858892432400665E+00 1.5000000000000000E+01 4.7899226612183057E+01
I -4.6822644133865452E+01 4.7193939633826801E+02 1.8218688500424494E+03 1.9106072476628399E+03 4.7193939633826801E+02
I 2.0915999999999999E+03 0.0000000000000000E+00 1.0838324524288516E+03 1.1550788089355601E+03 0.0000000000000000E+00
I 1.4312481267097157E+03 1.2051057740240391E+02 5.9489422597596089E+01 5.7243409761885879E+01 1.2275659023811413E+02
I 4.7899226612183057E+01 2.0000000000000001E-01 0.0000000000000000E+00 3.0000000000000000E+01 0.0000000000000000E+00
I 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 2.5510145278337426E+01 -7.0481740037058444E+02 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
O 3.0000000000000000E+01 2.2000000000000000E+01
*** Warning at time : 5555.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 441 : The inputs to the listed units have not converged at this timestep. The values at the last iteration will be used and the simulation will proceed.
Reported information : UNITS: 56
*** Fatal Error at time : 5555.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 450 : The maximum number of warnings allowed per simulation has been exceeded. Please fix these warnings or increase the limit on the number of warnings allowed per simulation (LIMITS command)
Reported information : Not available
*** Warning at time : 5555.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : The simulation failed to converge during 23 timesteps (0% of the time).
*********************************************************************************************************
The Following UNIT Numbers, TYPE Numbers, and Logical Units Were Used in the Supplied TRNSYS Input File:
13 2 4
15 15 6
16 56 9
17 62 34
18 65 35
19 579 36
25 37
56 38
66 39
200
*********************************************************************************************************
Total TRNSYS Calculation Time: 70.6000 Seconds
-------------- next part --------------
 TRNSYS - the TRaNsient SYstem Simulation program
The Solar Energy Lab at the University of Wisconsin - Madison, USA
Le Centre Scientifique et Technique du Batiment, Sophia Antipolis, France
Transsolar Energietechnik GmBH, Stuttgart, Germany
Thermal Energy System Specialists, LLC, Madison Wisconsin, USA
Release 17.01.0025
Listing file for: "C:\Trnsys17\MyProjects\BuildingProject9\BuildingProject9.dck"
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : The TRNSYS Executable (TRNExe.exe) and main DLL (TRNDll.dll) are located in "C:\Trnsys17\Exe"
*** Pre-Processing the TRNSYS EQUATIONs and CONSTANTs to check for fatal errors.
*** Warning at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 11 : The TRNSYS processor has reported an illegal variable name in an EQUATIONS or CONSTANTS card. Equations or constants must not begin with END, INC, EQU or CON as these are protected codes required when reading the TRNSYS input file. The offending variable name is listed below.
Reported information : CONTROL_COMFORT
*** Warning at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 11 : The TRNSYS processor has reported an illegal variable name in an EQUATIONS or CONSTANTS card. Equations or constants must not begin with END, INC, EQU or CON as these are protected codes required when reading the TRNSYS input file. The offending variable name is listed below.
Reported information : CONTROL_COLD
*** Warning at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 11 : The TRNSYS processor has reported an illegal variable name in an EQUATIONS or CONSTANTS card. Equations or constants must not begin with END, INC, EQU or CON as these are protected codes required when reading the TRNSYS input file. The offending variable name is listed below.
Reported information : CONTROL_WARM
*** Warning at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 11 : The TRNSYS processor has reported an illegal variable name in an EQUATIONS or CONSTANTS card. Equations or constants must not begin with END, INC, EQU or CON as these are protected codes required when reading the TRNSYS input file. The offending variable name is listed below.
Reported information : CONTROL_TOTAL
*** Pre-Processing of EQUATIONs and CONSTANTs completed with no fatal errors found.
*** Evaluating the EQUATIONs and CONSTANTs to determine their initial values.
*** Finished evaluating the EQUATIONs and CONSTANTs and ready to begin processing the remainder of the TRNSYS input file.
VERSION 17
*******************************************************************************
*** TRNSYS input file (deck) generated by TrnsysStudio
*** on zaterdag, mei 04, 2013 at 13:03
*** from TrnsysStudio project: C:\Trnsys17\MyProjects\BuildingProject9\BuildingProject9.tpf
***
*** If you edit this file, use the File/Import TRNSYS Input File function in
*** TrnsysStudio to update the project.
***
*** If you have problems, questions or suggestions please contact your local
*** TRNSYS distributor or mailto:software at cstb.fr
***
*******************************************************************************
*******************************************************************************
*** Units
*******************************************************************************
*******************************************************************************
*** Control cards
*******************************************************************************
* START, STOP and STEP
CONSTANTS 3
START=0
STOP=8760
STEP=1
! Start time End time Time step
SIMULATION 0.0000000000000000E+00 8.7600000000000000E+03 1.0000000000000000E+00
! Integration Convergence
TOLERANCES 1.0000000000000002E-03 1.0000000000000002E-03
! Max iterations Max warnings Trace limit
LIMITS 30 30 31
! TRNSYS numerical integration solver method
DFQ 1
! TRNSYS output file width, number of characters
WIDTH 72
! NOLIST statement
LIST
! MAP statement
! Solver statement Minimum relaxation factor Maximum relaxation factor
SOLVER 0
1.000000000000000
1.000000000000000
! Nan DEBUG statement
NAN_CHECK 0
! Overwrite DEBUG statement
OVERWRITE_CHECK 0
! disable time report
TIME_REPORT 0
! EQUATION SOLVER statement
EQUATION SOLVING METHOD 0
* User defined CONSTANTS
* EQUATIONS "Turn"
*
EQUATIONS 13
TURN = 0
! northern hemisphere: 1 - southern hemisphere: -1
HEMISPHERE = 1
! azimuth angle of orientation
AA_H_0_0 = 0
! azimuth angle of orientation
AA_S_0_90 = (0 +TURN)*GT(HEMISPHERE,0)+ (180-0 -TURN)*NOT(GT(HEMISPHERE,0))
! azimuth angle of orientation
AA_W_45_90 = (45 +TURN)*GT(HEMISPHERE,0)+ (180-45-TURN)*NOT(GT(HEMISPHERE,0))
! azimuth angle of orientation
AA_W_90_90 = (90 +TURN)*GT(HEMISPHERE,0)+ (180-90-TURN)*NOT(GT(HEMISPHERE,0))
! azimuth angle of orientation
AA_N_135_90 = (135+TURN)*GT(HEMISPHERE,0)+ (180-135-TURN)*NOT(GT(HEMISPHERE,0))
! azimuth angle of orientation
AA_N_180_90 = (180+TURN)*GT(HEMISPHERE,0)+ (180-180-TURN)*NOT(GT(HEMISPHERE,0))
! azimuth angle of orientation
AA_E_225_90 = (225+TURN)*GT(HEMISPHERE,0)+ (180-225-TURN)*NOT(GT(HEMISPHERE,0))
! azimuth angle of orientation
AA_E_270_90 = (270+TURN)*GT(HEMISPHERE,0)+ (180-270-TURN)*NOT(GT(HEMISPHERE,0))
! azimuth angle of orientation
AA_S_315_90 = (315+TURN)*GT(HEMISPHERE,0)+ (180-315-TURN)*NOT(GT(HEMISPHERE,0))
!solar azimuth corrected for southern hemisphere such that north=180, south=0, west =90, east=-90
AAZM_CORR_HEM = AAZM*GT(HEMISPHERE,0) + NOT(GT(HEMISPHERE,0))*((180-AAZM)*GT(AAZM,0)*LE(AAZM,180) + (-180-AAZM)*NOT(GT(AAZM,0)*LE(AAZM,180)))
! solar azimuth corrected by building rotation - Input for Type 56 sun position for SHM and ISM
AAZM_TYPE56 = (AAZM_CORR_HEM - TURN)
*$UNIT_NAME Turn
*$LAYER Main
*$POSITION 52 63
*------------------------------------------------------------------------------
* EQUATIONS "Radiation"
*
EQUATIONS 31
AZEN = [15,16]
AAZM = [15,17]
!Sky diffuse radiation on the horizontal
ID_H_0_0 = [15,20]
!Total incident of radation orientation H_0_0
IT_H_0_0 = [15,24]
!Beam incident of radation orientation H_0_0
IB_H_0_0 = [15,33]
!Incident angle of orientation H_0_0
AI_H_0_0 = [15,69]
IT_S_0_90 = [15,25]
IB_S_0_90 = [15,34]
AI_S_0_90 = [15,70]
IT_W_45_90 = [15,26]
IB_W_45_90 = [15,35]
AI_W_45_90 = [15,71]
IT_W_90_90 = [15,27]
IB_W_90_90 = [15,36]
AI_W_90_90 = [15,72]
IT_N_135_90 = [15,28]
IB_N_135_90 = [15,37]
AI_N_135_90 = [15,73]
IT_N_180_90 = [15,29]
IB_N_180_90 = [15,38]
AI_N_180_90 = [15,74]
IT_E_225_90 = [15,30]
IB_E_225_90 = [15,39]
AI_E_225_90 = [15,75]
IT_E_270_90 = [15,31]
IB_E_270_90 = [15,40]
AI_E_270_90 = [15,76]
IT_S_315_90 = [15,32]
IB_S_315_90 = [15,41]
AI_S_315_90 = [15,77]
hour_of_day = MOD(TIME,24)
*$UNIT_NAME Radiation
*$LAYER Main
*$POSITION 203 127
*------------------------------------------------------------------------------
* EQUATIONS "Cooling"
*
EQUATIONS 1
T_COOL_ON = max( min( 27, ([15,1]/3+49/3) ), 25)
*$UNIT_NAME Cooling
*$LAYER Main
*$POSITION 672 596
*------------------------------------------------------------------------------
* EQUATIONS "Shading+Light"
*
EQUATIONS 1
! 27
BRIGHT = [200,1]
*$UNIT_NAME Shading+Light
*$LAYER Controls
*$POSITION 661 724
*------------------------------------------------------------------------------
* Model "Weather data" (Type 15)
*
UNIT 15 TYPE 15 data
*$UNIT_NAME Weather data
*$MODEL .\Weather Data Reading and Processing\Standard Format\TMY2\Type15-2.tmf
*$POSITION 96 202
*$LAYER Main #
PARAMETERS 33
! 1 File Type
! 2 Logical unit
! 3 Tilted Surface Radiation Mode
! 4 Ground reflectance - no snow
! 5 Ground reflectance - snow cover
! 6 Number of surfaces
! 7 Tracking mode-1
! 8 Slope of surface-1
! 9 Azimuth of surface-1
! 10 Tracking mode-2
! 11 Slope of surface-2
! 12 Azimuth of surface-2
! 13 Tracking mode-3
! 14 Slope of surface-3
! 15 Azimuth of surface-3
! 16 Tracking mode-4
! 17 Slope of surface-4
! 18 Azimuth of surface-4
! 19 Tracking mode-5
! 20 Slope of surface-5
! 21 Azimuth of surface-5
! 22 Tracking mode-6
! 23 Slope of surface-6
! 24 Azimuth of surface-6
! 25 Tracking mode-7
! 26 Slope of surface-7
! 27 Azimuth of surface-7
! 28 Tracking mode-8
! 29 Slope of surface-8
! 30 Azimuth of surface-8
! 31 Tracking mode-9
! 32 Slope of surface-9
! 33 Azimuth of surface-9
2.0000000000000000E+00 3.4000000000000000E+01 5.0000000000000000E+00 2.0000000000000001E-01 7.0000000000000007E-01
9.0000000000000000E+00 1.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 1.0000000000000000E+00
9.0000000000000000E+01 0.0000000000000000E+00 1.0000000000000000E+00 9.0000000000000000E+01 4.5000000000000000E+01
1.0000000000000000E+00 9.0000000000000000E+01 9.0000000000000000E+01 1.0000000000000000E+00 9.0000000000000000E+01
1.3500000000000000E+02 1.0000000000000000E+00 9.0000000000000000E+01 1.8000000000000000E+02 1.0000000000000000E+00
9.0000000000000000E+01 2.2500000000000000E+02 1.0000000000000000E+00 9.0000000000000000E+01 2.7000000000000000E+02
1.0000000000000000E+00 9.0000000000000000E+01 3.1500000000000000E+02
*** External files
ASSIGN C:\Trnsys17\Weather\Meteonorm\Europe\NL-Amsterdam-Schiphol-62400.tm2 34
*|? Which file contains the TMY-2 weather data? |1000
*------------------------------------------------------------------------------
* EQUATIONS "Light Thresholds"
*
EQUATIONS 2
IT_LIGHT_ON = -3.6*120
IT_LIGHT_OFF = -3.6*200
*$UNIT_NAME Light Thresholds
*$LAYER Controls
*$POSITION 469 532
*------------------------------------------------------------------------------
* Model "Lights" (Type 2)
*
UNIT 200 TYPE 2
*$UNIT_NAME Lights
*$MODEL .\Controllers\Differential Controller w_ Hysteresis\generic\Solver 0 (Successive Substitution) Control Strategy\Type2d.tmf
*$POSITION 559 543
*$LAYER Controls #
*$# NOTE: This controller can only be used with Solver 0 (Successive substitution)
*$#
*$#
*$#
*$#
*$#
*$#
*$#
*$#
*$#
PARAMETERS 2
! 1 No. of oscillations
! 2 High limit cut-out
5.0000000000000000E+00 4.0000000000000000E+04
INPUTS 6
! [unconnected] Upper input value
! Radiation:IT_H_0_0 ->Lower input value
! [unconnected] Monitoring value
! Lights:Output control function ->Input control function
! [equation] Upper dead band
! [equation] Lower dead band
CONST IT_H_0_0 CONST 200,1 IT_LIGHT_ON
IT_LIGHT_OFF
*** INITIAL INPUT VALUES
0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 -4.3200000000000000E+02
-7.2000000000000000E+02
*------------------------------------------------------------------------------
* Model "Building" (Type 56)
*
UNIT 56 TYPE 56
*$UNIT_NAME Building
*$MODEL .\Loads and Structures\Multi-Zone Building\Type56.tmf
*$POSITION 824 578
*$LAYER Main # #
*$#
PARAMETERS 3
! 1 Logical unit for building description file (.bui)
! 2 Star network calculation switch
! 3 Weighting factor for operative temperature
3.5000000000000000E+01 1.0000000000000000E+00 5.0000000000000000E-01
INPUTS 29
! Tout:output -> 1- TAMB
! Weather data:Percent relative humidity -> 2- RELHUMAMB
! Weather data:Effective sky temperature -> 3- TSKY
! Tout:output -> 4- TSGRD
! Weather data:Solar zenith angle -> 5- AZEN
! Turn:AAZM_TYPE56 -> 6- AAZM
! Radiation:IT_N_180_90 -> 7- IT_N_180_90
! Radiation:IT_S_0_90 -> 8- IT_S_0_90
! Radiation:IT_E_270_90 -> 9- IT_E_270_90
! Radiation:IT_W_90_90 -> 10- IT_W_90_90
! Radiation:IT_H_0_0 -> 11- IT_H_0_0
! Radiation:IB_N_180_90 -> 12- IB_N_180_90
! Radiation:IB_S_0_90 -> 13- IB_S_0_90
! Radiation:IB_E_270_90 -> 14- IB_E_270_90
! Radiation:IB_W_90_90 -> 15- IB_W_90_90
! Radiation:IB_H_0_0 -> 16- IB_H_0_0
! Radiation:AI_N_180_90 -> 17- AI_N_180_90
! Radiation:AI_S_0_90 -> 18- AI_S_0_90
! Radiation:AI_E_270_90 -> 19- AI_E_270_90
! Radiation:AI_W_90_90 -> 20- AI_W_90_90
! Radiation:AI_H_0_0 -> 21- AI_H_0_0
! Weather data:Ground reflectance -> 22- GRDREF
! [unconnected] 23- CNAT_1
! Schedules:T_Cool_On_2 -> 24- T_COOL_ON
! [unconnected] 25- MS_N_180_90
! [unconnected] 26- MS_S_0_90
! [unconnected] 27- MS_E_270_90
! [unconnected] 28- MS_W_90_90
! Shading+Light:BRIGHT -> 29- BRIGHT
16,1 15,7 15,4 16,1 15,16
AAZM_TYPE56 IT_N_180_90 IT_S_0_90 IT_E_270_90 IT_W_90_90
IT_H_0_0 IB_N_180_90 IB_S_0_90 IB_E_270_90 IB_W_90_90
IB_H_0_0 AI_N_180_90 AI_S_0_90 AI_E_270_90 AI_W_90_90
AI_H_0_0 15,123 CONST T_COOL_ON_2 CONST
CONST CONST CONST BRIGHT
*** INITIAL INPUT VALUES
0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
0.0000000000000000E+00 2.0000000000000001E-01 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
*** External files
ASSIGN BuildingProject9.b17 35
*|? Building description file (*.bui) |1000
*------------------------------------------------------------------------------
* Model "Temperature" (Type 65)
*
UNIT 25 TYPE 65
*$UNIT_NAME Temperature
*$MODEL .\Output\Online Plotter\Online Plotter Without File\Type65d.tmf
*$POSITION 1089 650
*$LAYER Main # #
PARAMETERS 12
! 1 Nb. of left-axis variables
! 2 Nb. of right-axis variables
! 3 Left axis minimum
! 4 Left axis maximum
! 5 Right axis minimum
! 6 Right axis maximum
! 7 Number of plots per simulation
! 8 X-axis gridpoints
! 9 Shut off Online w/o removing
! 10 Logical unit for output file
! 11 Output file units
! 12 Output file delimiter
2.0000000000000000E+00 3.0000000000000000E+00 -2.0000000000000000E+03 5.0000000000000000E+03 -1.5000000000000000E+01
3.5000000000000000E+01 1.0000000000000000E+00 1.2000000000000000E+01 0.0000000000000000E+00 -1.0000000000000000E+00
0.0000000000000000E+00 0.0000000000000000E+00
INPUTS 5
! Schedules:Cooling ->Left axis variable-1
! Schedules:Heating ->Left axis variable-2
! Schedules:T_Cool_On_2 ->Right axis variable-1
! Schedules:T_Heat_On ->Right axis variable-2
! Cooling:T_COOL_ON ->Right axis variable-3
COOLING HEATING T_COOL_ON_2 T_HEAT_ON T_COOL_ON
*** INITIAL INPUT VALUES
Cooling Heating TCOOL_TEST _ATG THEAT _TEST_ATG TCOOL_TEST_ATG
LABELS 3
ATG Controls
Temperatures ATG [deg C]
ATG temperatures
*------------------------------------------------------------------------------
* Model "Irradiation" (Type 65)
*
UNIT 66 TYPE 65
*$UNIT_NAME Irradiation
*$MODEL .\Output\Online Plotter\Online Plotter Without File\Type65d.tmf
*$POSITION 915 84
*$LAYER Main # #
PARAMETERS 12
! 1 Nb. of left-axis variables
! 2 Nb. of right-axis variables
! 3 Left axis minimum
! 4 Left axis maximum
! 5 Right axis minimum
! 6 Right axis maximum
! 7 Number of plots per simulation
! 8 X-axis gridpoints
! 9 Shut off Online w/o removing
! 10 Logical unit for output file
! 11 Output file units
! 12 Output file delimiter
5.0000000000000000E+00 6.0000000000000000E+00 0.0000000000000000E+00 3.6000000000000000E+03 0.0000000000000000E+00
3.6000000000000000E+03 1.0000000000000000E+00 1.2000000000000000E+01 0.0000000000000000E+00 -1.0000000000000000E+00
0.0000000000000000E+00 0.0000000000000000E+00
INPUTS 11
! Radiation:IT_H_0_0 ->Left axis variable-1
! Radiation:IT_S_0_90 ->Left axis variable-2
! Radiation:IT_W_90_90 ->Left axis variable-3
! Radiation:IT_N_180_90 ->Left axis variable-4
! Radiation:IT_E_270_90 ->Left axis variable-5
! Radiation:IB_H_0_0 ->Right axis variable-1
! Radiation:IB_S_0_90 ->Right axis variable-2
! Radiation:IB_W_90_90 ->Right axis variable-3
! Radiation:IB_N_180_90 ->Right axis variable-4
! Radiation:IB_E_270_90 ->Right axis variable-5
! Radiation:hour_of_day ->Right axis variable-6
IT_H_0_0 IT_S_0_90 IT_W_90_90 IT_N_180_90 IT_E_270_90
IB_H_0_0 IB_S_0_90 IB_W_90_90 IB_N_180_90 IB_E_270_90
HOUR_OF_DAY
*** INITIAL INPUT VALUES
IT_H_0_0 IT_S_0_90 IT_W_90_90 IT_N_ 180_90 IT_E_270_90
IB_H_0_0 IB_S_0_90 IB_W_90_90 IB_N_ 180_90 IB_E_270_90
hour_of_day
LABELS 3
Total Incident Solar Radition [kJ/hr m²]
Beam Incident Solar Radition [kJ/hr m²]
Irradition
*------------------------------------------------------------------------------
* EQUATIONS "ATG"
*
EQUATIONS 7
Tcomfort = 21.45+0.11*[13,1]
Th90 = 23.45+0.11*[13,1]
Tl90 = 19.45+0.11*[13,1]
Control_comfort = ae(Tcomfort,[56,1],2)
*** Warning at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 11 : The TRNSYS processor has reported an illegal variable name in an EQUATIONS or CONSTANTS card. Equations or constants must not begin with END, INC, EQU or CON as these are protected codes required when reading the TRNSYS input file. The offending variable name is listed below.
Reported information : CONTROL_COMFORT
Control_cold = le([56,1],Tl90)
*** Warning at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 11 : The TRNSYS processor has reported an illegal variable name in an EQUATIONS or CONSTANTS card. Equations or constants must not begin with END, INC, EQU or CON as these are protected codes required when reading the TRNSYS input file. The offending variable name is listed below.
Reported information : CONTROL_COLD
Control_warm = ge([56,1],Th90)
*** Warning at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 11 : The TRNSYS processor has reported an illegal variable name in an EQUATIONS or CONSTANTS card. Equations or constants must not begin with END, INC, EQU or CON as these are protected codes required when reading the TRNSYS input file. The offending variable name is listed below.
Reported information : CONTROL_WARM
Control_total = Control_comfort+Control_cold+Control_warm
*** Warning at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 11 : The TRNSYS processor has reported an illegal variable name in an EQUATIONS or CONSTANTS card. Equations or constants must not begin with END, INC, EQU or CON as these are protected codes required when reading the TRNSYS input file. The offending variable name is listed below.
Reported information : CONTROL_TOTAL
*$UNIT_NAME ATG
*$LAYER Main
*$POSITION 820 490
*------------------------------------------------------------------------------
* Model "Teref" (Type 62)
*
UNIT 13 TYPE 62
*$UNIT_NAME Teref
*$MODEL .\Utility\Calling External Programs\Excel\Type62.tmf
*$POSITION 899 404
*$LAYER Main #
PARAMETERS 4
! 1 Mode
! 2 Nb of inputs
! 3 Nb of outputs
! 4 Show Excel
0.0000000000000000E+00 1.0000000000000000E+00 1.0000000000000000E+00 0.0000000000000000E+00
INPUTS 1
! Time:DAYNUM ->input
DAYNUM
*** INITIAL INPUT VALUES
0.0000000000000000E+00
LABELS 1
Afleestabel Teref.xls
*------------------------------------------------------------------------------
* EQUATIONS "Time"
*
EQUATIONS 4
DAYNUM = 1+INT(TIME/24)
WEEK = 1+INT(TIME/(7*24))
DAYWEEK = 7+DAYNUM-WEEK*7
Time_of_year = Time
*$UNIT_NAME Time
*$LAYER Main
*$POSITION 859 258
*------------------------------------------------------------------------------
* Model "Tout" (Type 62)
*
UNIT 16 TYPE 62
*$UNIT_NAME Tout
*$MODEL .\Utility\Calling External Programs\Excel\Type62.tmf
*$POSITION 995 426
*$LAYER Main #
PARAMETERS 4
! 1 Mode
! 2 Nb of inputs
! 3 Nb of outputs
! 4 Show Excel
0.0000000000000000E+00 1.0000000000000000E+00 1.0000000000000000E+00 0.0000000000000000E+00
INPUTS 1
! Time:Time_of_year ->input
TIME_OF_YEAR
*** INITIAL INPUT VALUES
0.0000000000000000E+00
LABELS 1
Afleestabel Tout.xls
*------------------------------------------------------------------------------
* Model "Internal loads" (Type 579)
*
UNIT 17 TYPE 579 loads
*$UNIT_NAME Internal loads
*$MODEL .\Utility Library (TESS)\Forcing Functions\Multi-Level Functions\3-Level Function\Type579.tmf
*$POSITION 195 636
*$LAYER Main #
*$# Possible Uses:
*$# Temperature Setpoints in a House/Building
*$# Ocupancy Patterns for a School
*$# Controller for Detailed Pumping Scheme
PARAMETERS 25
! 1 Number of tiers
! 2 Length of primary cycle
! 3 Length of secondary cycle
! 4 Length of tertiary cycle
! 5 # On Periods - Primary Cycle
! 6 Start of ON Period for Cycle 1
! 7 End of ON Period for Cycle 1
! 8 # On Periods - Secondary Cycle, Primary OFF
! 9 Start of ON Period for Cycle 2
! 10 End of ON Period for Cycle 2
! 11 # On Periods - Secondary Cycle, Primary ON
! 12 Start of ON Period for Cycle 3
! 13 End of ON Period for Cycle 3
! 14 # On Periods - Tertiary Cycle, Primary OFF, Secondary OFF
! 15 Start of ON Period for Cycle 4
! 16 End of ON Period for Cycle 4
! 17 # On Periods - Tertiary Cycle, Primary OFF, Secondary ON
! 18 Start of ON Period for Cycle 5
! 19 End of ON Period for Cycle 5
! 20 # On Periods - Tertiary Cycle, Primary ON, Secondary OFF
! 21 Start of ON Period for Cycle 6
! 22 End of ON Period for Cycle 6
! 23 # On Periods - Tertiary Cycle, Primary ON, Secondary N
! 24 Start of ON Period for Cycle 7
! 25 End of ON Period for Cycle 7
3.0000000000000000E+00 8.7600000000000000E+03 1.6800000000000000E+02 2.4000000000000000E+01 1.0000000000000000E+00
0.0000000000000000E+00 8.7600000000000000E+03 1.0000000000000000E+00 0.0000000000000000E+00 1.2000000000000000E+02
1.0000000000000000E+00 0.0000000000000000E+00 1.2000000000000000E+02 1.0000000000000000E+00 0.0000000000000000E+00
2.4000000000000000E+01 1.0000000000000000E+00 8.0000000000000000E+00 1.8000000000000000E+01 1.0000000000000000E+00
0.0000000000000000E+00 2.4000000000000000E+01 1.0000000000000000E+00 8.0000000000000000E+00 1.8000000000000000E+01
INPUTS 8
! [unconnected] Value of Function (OFF,OFF,OFF)
! [unconnected] Value of Function (OFF,OFF,ON)
! [unconnected] Value of Function (OFF,ON,OFF)
! [unconnected] Value of Function (OFF,ON,ON)
! [unconnected] Value of Function (ON,OFF,OFF)
! [unconnected] Value of Function (ON,OFF,ON)
! [unconnected] Value of Function (ON,ON,OFF)
! [unconnected] Value of Function (ON,ON,ON)
CONST AR CONST CONST CONST 0 CONST 0
CONST CONST CONST
*** INITIAL INPUT VALUES
0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
0.0000000000000000E+00 0.0000000000000000E+00 1.0000000000000000E+00
*------------------------------------------------------------------------------
* Model "Ventilation" (Type 579)
*
UNIT 18 TYPE 579
*$UNIT_NAME Ventilation
*$MODEL .\Utility Library (TESS)\Forcing Functions\Multi-Level Functions\3-Level Function\Type579.tmf
*$POSITION 188 700
*$LAYER Main #
*$# Possible Uses:
*$# Temperature Setpoints in a House/Building
*$# Ocupancy Patterns for a School
*$# Controller for Detailed Pumping Scheme
PARAMETERS 25
! 1 Number of tiers
! 2 Length of primary cycle
! 3 Length of secondary cycle
! 4 Length of tertiary cycle
! 5 # On Periods - Primary Cycle
! 6 Start of ON Period for Cycle 1
! 7 End of ON Period for Cycle 1
! 8 # On Periods - Secondary Cycle, Primary OFF
! 9 Start of ON Period for Cycle 2
! 10 End of ON Period for Cycle 2
! 11 # On Periods - Secondary Cycle, Primary ON
! 12 Start of ON Period for Cycle 3
! 13 End of ON Period for Cycle 3
! 14 # On Periods - Tertiary Cycle, Primary OFF, Secondary OFF
! 15 Start of ON Period for Cycle 4
! 16 End of ON Period for Cycle 4
! 17 # On Periods - Tertiary Cycle, Primary OFF, Secondary ON
! 18 Start of ON Period for Cycle 5
! 19 End of ON Period for Cycle 5
! 20 # On Periods - Tertiary Cycle, Primary ON, Secondary OFF
! 21 Start of ON Period for Cycle 6
! 22 End of ON Period for Cycle 6
! 23 # On Periods - Tertiary Cycle, Primary ON, Secondary N
! 24 Start of ON Period for Cycle 7
! 25 End of ON Period for Cycle 7
3.0000000000000000E+00 8.7600000000000000E+03 1.6800000000000000E+02 2.4000000000000000E+01 1.0000000000000000E+00
0.0000000000000000E+00 8.7600000000000000E+03 1.0000000000000000E+00 0.0000000000000000E+00 1.2000000000000000E+02
1.0000000000000000E+00 0.0000000000000000E+00 1.2000000000000000E+02 1.0000000000000000E+00 0.0000000000000000E+00
2.4000000000000000E+01 1.0000000000000000E+00 7.0000000000000000E+00 1.8000000000000000E+01 1.0000000000000000E+00
0.0000000000000000E+00 2.4000000000000000E+01 1.0000000000000000E+00 7.0000000000000000E+00 1.8000000000000000E+01
INPUTS 8
! [unconnected] Value of Function (OFF,OFF,OFF)
! [unconnected] Value of Function (OFF,OFF,ON)
! [unconnected] Value of Function (OFF,ON,OFF)
! [unconnected] Value of Function (OFF,ON,ON)
! [unconnected] Value of Function (ON,OFF,OFF)
! [unconnected] Value of Function (ON,OFF,ON)
! [unconnected] Value of Function (ON,ON,OFF)
! [unconnected] Value of Function (ON,ON,ON)
CONST AR CONST CONST CONST 0 CONST 0
CONST CONST CONST
*** INITIAL INPUT VALUES
0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
0.0000000000000000E+00 0.0000000000000000E+00 1.0000000000000000E+00
*------------------------------------------------------------------------------
* Model "Heating and cooling" (Type 579)
*
UNIT 19 TYPE 579 and cooling
*$UNIT_NAME Heating and cooling
*$MODEL .\Utility Library (TESS)\Forcing Functions\Multi-Level Functions\3-Level Function\Type579.tmf
*$POSITION 191 764
*$LAYER Main #
*$# Possible Uses:
*$# Temperature Setpoints in a House/Building
*$# Ocupancy Patterns for a School
*$# Controller for Detailed Pumping Scheme
PARAMETERS 25
! 1 Number of tiers
! 2 Length of primary cycle
! 3 Length of secondary cycle
! 4 Length of tertiary cycle
! 5 # On Periods - Primary Cycle
! 6 Start of ON Period for Cycle 1
! 7 End of ON Period for Cycle 1
! 8 # On Periods - Secondary Cycle, Primary OFF
! 9 Start of ON Period for Cycle 2
! 10 End of ON Period for Cycle 2
! 11 # On Periods - Secondary Cycle, Primary ON
! 12 Start of ON Period for Cycle 3
! 13 End of ON Period for Cycle 3
! 14 # On Periods - Tertiary Cycle, Primary OFF, Secondary OFF
! 15 Start of ON Period for Cycle 4
! 16 End of ON Period for Cycle 4
! 17 # On Periods - Tertiary Cycle, Primary OFF, Secondary ON
! 18 Start of ON Period for Cycle 5
! 19 End of ON Period for Cycle 5
! 20 # On Periods - Tertiary Cycle, Primary ON, Secondary OFF
! 21 Start of ON Period for Cycle 6
! 22 End of ON Period for Cycle 6
! 23 # On Periods - Tertiary Cycle, Primary ON, Secondary N
! 24 Start of ON Period for Cycle 7
! 25 End of ON Period for Cycle 7
3.0000000000000000E+00 8.7600000000000000E+03 1.6800000000000000E+02 2.4000000000000000E+01 1.0000000000000000E+00
0.0000000000000000E+00 8.7600000000000000E+03 1.0000000000000000E+00 0.0000000000000000E+00 1.2000000000000000E+02
1.0000000000000000E+00 0.0000000000000000E+00 1.2000000000000000E+02 1.0000000000000000E+00 0.0000000000000000E+00
2.4000000000000000E+01 1.0000000000000000E+00 6.0000000000000000E+00 1.8000000000000000E+01 1.0000000000000000E+00
0.0000000000000000E+00 2.4000000000000000E+01 1.0000000000000000E+00 6.0000000000000000E+00 1.8000000000000000E+01
INPUTS 8
! [unconnected] Value of Function (OFF,OFF,OFF)
! [unconnected] Value of Function (OFF,OFF,ON)
! [unconnected] Value of Function (OFF,ON,OFF)
! [unconnected] Value of Function (OFF,ON,ON)
! [unconnected] Value of Function (ON,OFF,OFF)
! [unconnected] Value of Function (ON,OFF,ON)
! [unconnected] Value of Function (ON,ON,OFF)
! [unconnected] Value of Function (ON,ON,ON)
CONST AR CONST CONST CONST 0 CONST 0
CONST CONST CONST
*** INITIAL INPUT VALUES
0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00 0.0000000000000000E+00
0.0000000000000000E+00 0.0000000000000000E+00 1.0000000000000000E+00
*------------------------------------------------------------------------------
* EQUATIONS "Schedules"
*
EQUATIONS 4
Cooling = [19,1]*Control_warm
Heating = [19,1]*Control_cold
T_Heat_On = Heating*(Tl90-15)+15
T_Cool_On_2 = Cooling*Th90
*$UNIT_NAME Schedules
*$LAYER Main
*$POSITION 369 724
*------------------------------------------------------------------------------
END
TRANSIENT SIMULATION STARTING AT TIME = 0.0000000000000000E+00
STOPPING AT TIME = 8.7600000000000000E+03
TIMESTEP = 1 / 1
DIFFERENTIAL EQUATION ERROR TOLERANCE = 1.0000000000000002E-03
ALGEBRAIC CONVERGENCE TOLERANCE = 1.0000000000000002E-03
DIFFERENTIAL EQUATIONS SOLVED BY MODIFIED EULER
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 90 : TRNDll.dll is compiled in release mode. External DLLs will be loaded from the .\UserLib\ReleaseDLLs\ directory.
Reported information : Not available
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : The following Types were loaded from TRNDll.dll: Type62, Type15, Type65, Type2
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "FileReader.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSApplicationsLibrary_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSArchiveDLL_v2.04_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSControllersLibrary_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSElectricalLibrary_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSGHPLibraryType997_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSGHPLibrary_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSGroundCouplingLibrary_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSGroundCouplingType1244_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSGroundCouplingType1255_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSGroundCouplingType1256_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSGroundCouplingType957_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSGroundCouplingType993_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSHVACLibrary_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSHydronics_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSLoadsStructuresLibrary_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSOptimizationLibrary_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSSolarLibrary_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "TESSStorageLibrary_v17.1.03_Release.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : The following Types were loaded from "TESSUtilityLibrary_v17.1.03_Release.dll": Type579
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "type127.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "Type157.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : The following Types were loaded from "Type56.dll": Type56
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "Type76Lib.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "type79-W.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "Type79Lib.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
Message : "Type82Lib.dll" was found but did not contain any components from the input file.
*** Notice at time : 0.000000
Generated by Unit : Not applicable or not available
Generated by Type : Not applicable or not available
TRNSYS Message 199 : TRNSYS found at least one user DLL in the UserLib directory. (Note: Only DLL's including Types that are used in the simulation are loaded)
Reported information : 2 user DLLs were loaded after searching in "C:\Trnsys17\UserLib\ReleaseDLLs"
*** Notice at time : 0.000000
Generated by Unit : 56
Generated by Type : 56
Message : Shading mask file *.shm for external windows does not exist.
*** Notice at time : 0.000000
Generated by Unit : 56
Generated by Type : 56
Message : TRNFLOW (multi zone air flow model) messages are written in a separate file *.cer! Please, always check the *.cer file for information!!!
*** Notice at time : 0.000000
Generated by Unit : 56
Generated by Type : 56
Message : Active layers and internal window calculations integrated
*** Notice at time : 0.000000
Generated by Unit : 56
Generated by Type : 56
Message : No internal humidity calculations are performed and no condensation warnings are printed. if any of the outputs ntype 9,10,11,26,29,40,41,47,48 or 49 is specified The humidity calculations, using an internal timestep, will be switched on and condensation checks are performed
*** Notice at time : 0.000000
Generated by Unit : 56
Generated by Type : 56
Message : Star network calculation: every iteration step of TRNSYS
*** The TRNSYS components will be called in the following order:
Unit # 15 Type # 15
Unit # 200 Type # 2
Unit # 56 Type # 56
Unit # 13 Type # 62
Unit # 16 Type # 62
Unit # 17 Type # 579
Unit # 18 Type # 579
Unit # 19 Type # 579
Unit # 25 Type # 65
Unit # 66 Type # 65