[TRNSYS-users] Output Printers

[Mohammad Rezvanpour]

Thank you Jeff.
But I still get involved with it and I could not get the right output.

On Fri, Nov 10, 2017 at 12:40 AM, Jeff Thornton via TRNSYS-users <
trnsys-users at lists.onebuilding.org> wrote:

> <About print outputs (TYPE 25) While I plugged in the required outputs to
> the printer, but when I open the printer in Excel, the outputs are
> cluttered and completely unrelated. For example, I chose the power output
> of the panel, but the temperature and wind of the city of Tehran open in
> Excel, which is completely unrelated. Is not the problem with the Excel
> version? what's the solution?>
>
> What did you specify for the name of the output file in the printer
> proforma?  Sounds like you may have an issue with writing/reading from the
> same file.
>
> <For Plot printers (TYPE 65), when I get a graph, some lines are too thin
> to not be able to see the high resolution image. Is there any way I can
> zoom in or see a higher-quality photo with all the lines in it? This graph
> of the software shows cannot be used in any article, because lines are not
> clear except for some other lines.>
>
> You can use the "Thick Lines" option in the plotter, turn off any line you
> don;t want by clicking on it's name, or zoom into the window ((click and
> drag).
>
> <In Plot printers (TYPE 65), the vertical axis to the right of the graph
> shown with "Heat transfer rate" is different for each parameter? For
> example, for a power output, is the watt, for module temperature, is
> Celsius or Kelvin? For example, what is the heat transfer rate for PV
> efficiency? >
>
> The label for the plot is set in the Special Cards tab of the proforma.
>
> All of these items are discussed in great detail in the documentation.  I
> urge you to start there with questions.  There is a nice discussion on the
> Online plotter in the Tutorials manual.
>
>
>
> Jeff
>
> ---
> Jeff Thornton
> President - TESS LLC
> 22 N. Carroll Street, Madison WI USA 53703
> Office: (608) 274-2577  Fax: (608) 278-1475www.tess-inc.com
> E-Mail: thornton at tess-inc.com
>
> On 11/09/2017 2:54 pm, Mohammad Rezvanpour via TRNSYS-users wrote:
>
> Hello dear TRNSYS users
> good day
>
> I have three important questions about outputs
>
>
> 1- About print outputs (TYPE 25) While I plugged in the required outputs
> to the printer, but when I open the printer in Excel, the outputs are
> cluttered and completely unrelated. For example, I chose the power output
> of the panel, but the temperature and wind of the city of Tehran open in
> Excel, which is completely unrelated. Is not the problem with the Excel
> version? what's the solution?
>
> 2- For Plot printers (TYPE 65), when I get a graph, some lines are too
> thin to not be able to see the high resolution image. Is there any way I
> can zoom in or see a higher-quality photo with all the lines in it? This
> graph of the software shows cannot be used in any article, because lines
> are not clear except for some other lines.
>
> 3- In Plot printers (TYPE 65), the vertical axis to the right of the graph
> shown with "Heat transfer rate" is different for each parameter? For
> example, for a power output, is the watt, for module temperature, is
> Celsius or Kelvin? For example, what is the heat transfer rate for PV
> efficiency?
>
>
> I know there are a lot of questions, but I'm sure these are commonplace
> questions for you mates.
>
> Kind Regards.
> Mohammad
>
> --
> Regards.
>
> MSc. Student of Energy and Environmental Engineering at University of
> Tehran
>
> Hand-Phone: +989303037373
>
> _______________________________________________
> TRNSYS-users mailing listTRNSYS-users at lists.onebuilding.orghttp://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org
>
>
> _______________________________________________
> TRNSYS-users mailing list
> TRNSYS-users at lists.onebuilding.org
> http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org
>
>


-- 
Regards.

MSc. Student of Energy and Environmental Engineering at University of Tehran

Hand-Phone : +989303037373
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.onebuilding.org/pipermail/trnsys-users-onebuilding.org/attachments/20171110/4eb1049a/attachment.htm>