[TRNSYS-users] Climate data

Esteban Zalamea via TRNSYS-users trnsys-users at lists.onebuilding.org
Sun Nov 6 07:43:59 PST 2016


Hello every one

I am new user of TRNSYS. I am looking forward to simulate in Type 56 3D, but I just found that it is necessary to have TM2 climate data file? But for Cuenca, Ecuador I just found only .EPW file. It is possible to simulate in type 56 with EPW ? or it is possible to export EPW file to TM2? or using the adequate climate Type 15-4 ? Thank you in advance for your help



Kind regards

Esteban Zalamea León
Arquitecto
PhD Arquitectura y Urbanismo UBB
Coordinador Maestría en Construcciones
Universidad de Cuenca
Tlf 593 98 331 1604 /  07 405 1102 Ext. 2153


> El 06-11-2016, a las 10:09, Jeff Thornton via TRNSYS-users <trnsys-users at lists.onebuilding.org <mailto:trnsys-users at lists.onebuilding.org>> escribió:
> 
> Ismail,
> 
> Your approach of connecting the soil temperature to the boundary temperature will work but will likely over-estimate the loads - sometimes significantly.  The storage in the ground around the basement can play an important role.  There are several good ground modeling components out there but I would recommend Type1267 from TESS after looking at your schematic.  The model will likely slow down the simulation but will provide MUCH more realistic results.  And with the included soil temperature viewer you'll be able to visualize the heat transfer into the soil.  We use it on all of our basement projects.  There are several tricks we can share to help with the simulation speed issue too.
> 
> Jeff Thornton
> 
> Sent from my iPhone
> 
> On Nov 4, 2016, at 12:55 PM, Issmail OUHALLOU via TRNSYS-users <trnsys-users at lists.onebuilding.org <mailto:trnsys-users at lists.onebuilding.org>> wrote:
> 
>> ​Dear Trnsys-experts,
>> 
>> Would anyone happen to have an experience on advanced building modeling with basements included? I am trying to model a building in TRNSYS 17 using type 56. My building includes three basements as shown in figure below.
>> 
>> <317.4.1f-Fluchtwege-UG7.6.gif>
>> ​I am wondering if what I have done puts me in the right path, to know: I used Type 77 to model a simple ground temperature, then the output (soil temperature at Node) has been connected to TBOUNDARY. In fact, I have set three Nodes in type 77 (one node for each basement) and the walls's boundary conditions of the basements are = 1*TBOUNDARY.
>> 
>> Thanks in advance
>> 
>> Regards,
>> Ismail
>> 
>> _______________________________________________
>> TRNSYS-users mailing list
>> TRNSYS-users at lists.onebuilding.org <mailto:TRNSYS-users at lists.onebuilding.org>
>> http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org <http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org>
> _______________________________________________
> TRNSYS-users mailing list
> TRNSYS-users at lists.onebuilding.org <mailto:TRNSYS-users at lists.onebuilding.org>
> http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.onebuilding.org/pipermail/trnsys-users-onebuilding.org/attachments/20161106/b7812cf2/attachment-0003.htm>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: PastedGraphic-1.tiff
Type: image/tiff
Size: 92942 bytes
Desc: not available
URL: <http://lists.onebuilding.org/pipermail/trnsys-users-onebuilding.org/attachments/20161106/b7812cf2/attachment-0003.tiff>


More information about the TRNSYS-users mailing list