[TRNSYS-users] error - shiding/insulation matrix

Jeff Thornton via TRNSYS-users trnsys-users at lists.onebuilding.org
Fri May 20 07:30:57 PDT 2016


If you aren't interested in the impact of the PV on the building itself, and just want to use the building model to do the shading, then there are easier ways.  I would suggest you take a look at the shading mask model in TRNSYS and use google sketch up to calculate the obstruction angles for that model.  Then connect the shaded radiation from that model to the PV models.  In this way you can get as rigorous as you like.  You can model every single PV module individually with each one having different shading or you can lump them together into one array on each roof.  But please keep one of the earlier comments in mind - PV arrays can operate differently under partial shading conditions so make sure you do a little investigating....

Jeff

Sent from my iPhone

> On May 17, 2016, at 3:38 AM, Chaminda Ranaweera via TRNSYS-users <trnsys-users at lists.onebuilding.org> wrote:
> 
> I am simulating Solar PV installation output over a building by using Trnsys. There are two parts of the roof with different elevations. One part is shaded by other part of the roof. We supposed to install solar PV on both part of the roof. I want to find the solar radiations of both part of the roof in order to calculate solar PV out put of the roof. How can we use Trnsys for this simulation. I made a building drawing by using Google Sketch Up. Once I imported .idf file to Trnsys, it doesn’t show two roof with differenr radiations. It showa the roof as only one unit. In this case I cannot calculate the solar radiation on solar Pv panels in two roofs separately. Can we use Trnsys for this simulation.
> 
> 
> On Mon, 16 May 2016 07:16:45 -0500
> Esteban Zalamea via TRNSYS-users <trnsys-users at lists.onebuilding.org> wrote:
>> Hi Karol
>> Looks like there is no memory left.
>> Regards
>> Esteban Zalamea León
>> Arquitecto
>> PhD Arquitectura y Urbanismo UBB
>> Coordinador Maestría en Construcciones
>> Universidad de Cuenca
>> Tlf 593 98 331 1604 /  07 405 1102 Ext. 2153
>>> El 16-05-2016, a las 7:13, Karol BANDURSKI via TRNSYS-users <trnsys-users at lists.onebuilding.org> escribió:
>>> Dear Users,
>>> I would be grateful if somebody could help mi problem with generation shading/insulation matrix.
>>> If I do it I get error that print screen is attached…
>>> I try to look if in TRNSYS3d are some errors, but after exporting to idf file it seems that everything is ok…
>>> Regards,
>>> Karol
>>> ------------------------------------------------
>>> Karol Bandurski MSc.
>>> Institute of Environmental Engineering <http://www.ee.put.poznan.pl/>
>>> Poznan University of Technology
>>> www.put.poznan.pl/~karol.bandurski <http://www.put.poznan.pl/~karol.bandurski>
>>> www.ee.put.poznan.pl <http://www.ee.put.poznan.pl/>
>>>  <error.jpg>_______________________________________________
>>> TRNSYS-users mailing list
>>> TRNSYS-users at lists.onebuilding.org <mailto:TRNSYS-users at lists.onebuilding.org>
>>> http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org <http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org>
> 
> _______________________________________________
> TRNSYS-users mailing list
> TRNSYS-users at lists.onebuilding.org
> http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org




More information about the TRNSYS-users mailing list