[TRNSYS-users] TMY3 files in Demo Version

David BRADLEY d.bradley at tess-inc.com
Fri Apr 22 07:13:04 PDT 2016


Brad,
  I went to NREL's data site and got the Albany data file, saved it 
locally (leaving the extension of *.csv) and made a new project in the 
demo version using the Type15-TMY3 (Type 15 mode 7) proforma, indicated 
the Albany data file, put in an online plotter to watch temperature and 
ran the project without any errors. If you'd like to send me the file 
that you downloaded I can try that one too.
kind regards,
  David


On 04/21/2016 18:17, Brad Painting wrote:
> David,
> The file I downloaded directly from NREL (with CSV extension) produced 
> the same error message. I am pretty sure I did save it as tab 
> delimited because it was the only way I could figure out how to end in 
> a TMY3 extension rather than TMY3.CSV. (I am not sure if the CSV 
> extension is a problem).
>
> On Thu, Apr 21, 2016 at 12:41 PM, David BRADLEY 
> <d.bradley at tess-inc.com <mailto:d.bradley at tess-inc.com>> wrote:
>
>     Brad,
>      The official TMY3 syntax is comma separated. The file you
>     attached is tab delimited. Did you download it directly from an
>     NREL site or did it get processed (resaved as tab delimited?)
>     along the way?
>     best,
>      David
>
>
>
>     On 04/19/2016 18:15, Brad Painting wrote:
>>     David, here's the exact error message provided in the simulation
>>     log for Type 15:
>>
>>     "Message : Unable to correctly read from the supplied data file -
>>     please check the file and re-run the simulation."
>>
>>     I am using Type15-TMY3. The file I used is attached. I have tried
>>     it with a couple different ones and neither worked. Thanks for
>>     looking into it.
>>
>>     On Tue, Apr 19, 2016 at 11:48 AM, David BRADLEY
>>     <d.bradley at tess-inc.com <mailto:d.bradley at tess-inc.com>> wrote:
>>
>>         Brad,
>>           TMY3 files downloaded from NREL's site should work fine
>>         with the demo version. You do have to make sure that you are
>>         using the TMY3 mode of Type15. When you get the error, to
>>         what "it" do you refer? Is there an error generated by
>>         TRNSYS? Is Windows complaining about the file type? Some
>>         additional specifics about the source of the error and the
>>         language of the error would help in tracking down its cause.
>>         kind regards,
>>          David
>>
>>
>>         On 04/19/2016 07:05, Brad Painting wrote:
>>>         I currently do not have access to a paid TRNSYS subscription
>>>         and was trying to do a quick simulation of a PV array. Is it
>>>         possible to download TMY3 files from NREL to use in the Demo
>>>         version? When I try this it says the file type is not
>>>         recognized, even though it has the TMY3 extension. Thanks.
>>>
>>>
>>>         _______________________________________________
>>>         TRNSYS-users mailing list
>>>         TRNSYS-users at lists.onebuilding.org
>>>         <mailto:TRNSYS-users at lists.onebuilding.org>
>>>         http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org
>>
>>         -- 
>>         ***************************
>>         David BRADLEY
>>         Principal
>>         Thermal Energy Systems Specialists, LLC
>>         22 North Carroll Street - suite 370
>>         Madison, WI  53703 USA
>>
>>         P:+1.608.274.2577 <tel:%2B1.608.274.2577>
>>         F:+1.608.278.1475 <tel:%2B1.608.278.1475>
>>         d.bradley at tess-inc.com <mailto:d.bradley at tess-inc.com>
>>
>>         http://www.tess-inc.com
>>         http://www.trnsys.com
>>
>>
>>
>>
>>     -- 
>>
>>     Brad Painting
>>
>>     Master of Science Candidate, Renewable Energy Engineering
>>
>>     Department of Technology & Environmental Design
>>
>>     Appalachian State University
>>
>>     Boone, NC  28608
>>
>
>     -- 
>     ***************************
>     David BRADLEY
>     Principal
>     Thermal Energy Systems Specialists, LLC
>     22 North Carroll Street - suite 370
>     Madison, WI  53703 USA
>
>     P:+1.608.274.2577 <tel:%2B1.608.274.2577>
>     F:+1.608.278.1475 <tel:%2B1.608.278.1475>
>     d.bradley at tess-inc.com <mailto:d.bradley at tess-inc.com>
>
>     http://www.tess-inc.com
>     http://www.trnsys.com
>
>

-- 
***************************
David BRADLEY
Principal
Thermal Energy Systems Specialists, LLC
22 North Carroll Street - suite 370
Madison, WI  53703 USA

P:+1.608.274.2577
F:+1.608.278.1475
d.bradley at tess-inc.com

http://www.tess-inc.com
http://www.trnsys.com

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.onebuilding.org/pipermail/trnsys-users-onebuilding.org/attachments/20160422/15dafb02/attachment-0003.htm>


More information about the TRNSYS-users mailing list