[TRNSYS-users] Genopt trnbuild error (Martin Berov)

Marko Mancic markomancic at yahoo.com
Fri Apr 17 00:24:04 PDT 2015


Dear Martin,
You should write the complete path to your building file in type 56, even if it is located in the same directory as the project. Which optimization method are you using?If you are trying to use PSO or similar optimization method, which runs parallel trnsys simulations, you should limit the no. of cores used to 1. For some reason, Trnbuild locks the building file, so multiple instances of the simulation are not possible. However, you can try to run trn.exe in batch from genopt directly (without trnopt)  to avoid this.
Hope this helps.
Regards,
Marko
       From: "trnsys-users-request at lists.onebuilding.org" <trnsys-users-request at lists.onebuilding.org>
 To: trnsys-users at lists.onebuilding.org 
 Sent: Wednesday, April 15, 2015 10:05 PM
 Subject: TRNSYS-users Digest, Vol 124, Issue 20
   
----- Forwarded Message -----

Send TRNSYS-users mailing list submissions to
    trnsys-users at lists.onebuilding.org

To subscribe or unsubscribe via the World Wide Web, visit
    http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org

or, via email, send a message with subject or body 'help' to
    trnsys-users-request at lists.onebuilding.org

You can reach the person managing the list at
    trnsys-users-owner at lists.onebuilding.org

When replying, please edit your Subject line so it is more specific
than "Re: Contents of TRNSYS-users digest..."

Today's Topics:

  1. Genopt trnbuild error (Martin Berov)
  2. Re: Genopt trnbuild error (mcdowell at tess-inc.com)
Hi,
I'm using Genopt to optimize parameters of solar heating system (first just the collector area and slope). I compiled the input file, defined the variables in genopt i.e. everything as required. bu when I run the optimization i get error message as table where is written:

TrnbuildSurf-No                                       Description                                       Comment-1                                          no OUTPUT's specified                     please add at least one output
In the Trnsys simulation environment I get output results (the model is properly functioning)
Do you have idea what could be the problem?
Best RegardsMartin
Martin Berov -It is not finding your building model file when it starts the simulation.  GenOpt moves the files to run a simulation so you need to make sure all paths for files are complete.Regards,Tim ---
Timothy P. McDowell
Executive Vice President
Thermal Energy System Specialists, LLC
22 N Carroll St, Suite 370
Madison, WI 53703
608-274-2577On 2015-04-14 14:06, Martin Berov wrote:
Hi, I'm using Genopt to optimize parameters of solar heating system (first just the collector area and slope). I compiled the input file, defined the variables in genopt i.e. everything as required. bu when I run the optimization i get error message as table where is written: TrnbuildSurf-No                                       Description                                       Comment-1                                          no OUTPUT's specified                     please add at least one output In the Trnsys simulation environment I get output results (the model is properly functioning) Do you have idea what could be the problem? Best RegardsMartin 
_______________________________________________
TRNSYS-users mailing list
TRNSYS-users at lists.onebuilding.org
http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org


_______________________________________________
TRNSYS-users mailing list
TRNSYS-users at lists.onebuilding.org
http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org


  
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.onebuilding.org/pipermail/trnsys-users-onebuilding.org/attachments/20150417/81e17c0c/attachment.htm>


More information about the TRNSYS-users mailing list