[TRNSYS-users] Trnsys 17 - GenOpt
Amr Alaaeldin Elesawy
amr.alaaeldin at polimi.it
Sat Aug 30 06:32:11 PDT 2014
Dear Ines,
I agree with Jeff. It seems that you have a problem with the path
definition of the external files in your .dck file... I had a similar
example with finding the weather file I'm using... I'm writing the code
here below (only the part related to type 109, copied from the .dck file):
*CODE*
*---------*
* Model "Type109-TMY2" (Type 109)
*
UNIT 4 TYPE 109 Type109-TMY2
*$UNIT_NAME Type109-TMY2
*$MODEL .\Weather Data Reading and Processing\Standard
Format\TMY2\Type109-TMY2.tmf
*$POSITION 201 274
*$LAYER Weather - Data Files #
PARAMETERS 4
2 ! 1 Data Reader Mode
302 ! 2 Logical unit
4 ! 3 Sky model for diffuse radiation
1 ! 4 Tracking mode
INPUTS 9
0,0 ! [unconnected] Ground reflectance
0,0 ! [unconnected] Slope of surface-1
0,0 ! [unconnected] Azimuth of surface-1
0,0 ! [unconnected] Slope of surface-2
0,0 ! [unconnected] Azimuth of surface-2
0,0 ! [unconnected] Slope of surface-3
0,0 ! [unconnected] Azimuth of surface-3
0,0 ! [unconnected] Slope of surface-4
0,0 ! [unconnected] Azimuth of surface-4
*** INITIAL INPUT VALUES
0.2 90 180 90 0 90 -90 90 90
*** External files
ASSIGN* "IT-Palermo-Point-Raisi-164050.tm2" 302*
*|? Weather data file |1000
*The problem was in the red highlighted part... The corrected path I used
afterwards is here below:*
ASSIGN* "C:\Program
Files\Trnsys16\Examples\TRIAL02\IT-Palermo-Point-Raisi-164050.tm2" 302*
Also, I would recommend you check out the master thesis attached... It
helped a lot with initiating my first GenOpt Trials.
I hope this helps, please let me know if it works... I'm currently working
on a case sensitivity analysis and I'm trying to get the results in terms
of the MRT, PMV and PPD... I'm a bit stuck in how to show/post-process the
huge number of results, so I'm trying to see as many cases as possible to
get inspired.
Best of Luck,
Amr
On Fri, Aug 29, 2014 at 4:31 PM, Jeff Thornton <thornton at tess-inc.com>
wrote:
> Check the paths to all of your external files. The GenOpt program moves
> the decks to a temporary directory and if you have relative paths in your
> project, and not the full path location, the program will not be able to
> find the files.
>
> Jeff Thornton
> TESS
>
> Sent from my iPhone
>
> On Aug 29, 2014, at 8:07 AM, Ines Khalifa <khalifa_ines at hotmail.fr> wrote:
>
> Amr,
>
> Thank you for your quick answer.
> When running GenOpt, four folders are created named "tmp-genopt-run-1 / 2
> / 3 / 4", into each one, there is a log file (here below).
> As you can see, there is no error message in the log file, what i have
> attached at first time was the pop message of the error.
>
> Ines.
>
>
> TRNSYS - the TRaNsient SYstem Simulation program
>
> The Solar Energy Lab at the University of Wisconsin - Madison, USA
> Le Centre Scientifique et Technique du Batiment, Sophia Antipolis, France
> Transsolar Energietechnik GmBH, Stuttgart, Germany
> Thermal Energy System Specialists, LLC, Madison Wisconsin, USA
>
> Release 17.00.0019
>
> Simulation log for:
> "C:\Trnsys17\Examples\genopt-type56--3\tmp-genopt-run-2\GenOptRun.dck"
>
> *** Notice at time : 0.000000
> Generated by Unit : Not applicable or not available
> Generated by Type : Not applicable or not available
> Message : The TRNSYS Executable (TRNExe.exe) and main
> DLL (TRNDll.dll) are located in "C:\Trnsys17\Exe"
>
> *** Notice at time : 0.000000
> Generated by Unit : Not applicable or not available
> Generated by Type : 208
> TRNSYS Message 75 : The Type referenced below requires descriptors
> instead of initial values.
> Reported information : Type 208
>
> *** Notice at time : 0.000000
> Generated by Unit : Not applicable or not available
> Generated by Type : 535
> TRNSYS Message 75 : The Type referenced below requires descriptors
> instead of initial values.
> Reported information : Type 535
>
> *** Notice at time : 0.000000
> Generated by Unit : Not applicable or not available
> Generated by Type : 580
> TRNSYS Message 76 : The following Type has been identified as
> allowing the unit specifications (kg/h for example) after the input
> specifications and intial values for the inputs. The critical parameter
> number, and the value of this critical parameter that indicates that the
> units will be supplied is also listed. This information was retrieved from
> the VarUnits.dat file loacted in the \Exe directory of your TRNSYS 16
> installation.
> Reported information : Type 580, Critical Parameter 11, Parameter
> Value 1
>
> *** Notice at time : 0.000000
> Generated by Unit : Not applicable or not available
> Generated by Type : 580
> TRNSYS Message 88 : The following Type has been identified as
> allowing FORMAT statements. This information was retrieved from the
> Formats.dat file loacted in the \Exe directory of your TRNSYS 16
> installation.
> Reported information : Type 580
>
> *** Notice at time : 0.000000
> Generated by Unit : Not applicable or not available
> Generated by Type : Not applicable or not available
> TRNSYS Message 90 : TRNDll.dll is compiled in release mode.
> External DLLs will be loaded from the .\UserLib\ReleaseDLLs\ directory.
> Reported information : Not available
>
> *** Notice at time : 0.000000
> Generated by Unit : Not applicable or not available
> Generated by Type : Not applicable or not available
> Message : The following Types were loaded from
> TRNDll.dll: Type34, Type28, Type65, Type56, Type69, Type109, Type33
>
> *** Notice at time : 0.000000
> Generated by Unit : Not applicable or not available
> Generated by Type : Not applicable or not available
> Message : "FileReader.dll" was found but did not contain
> any components from the input file.
>
> *** Notice at time : 0.000000
> Generated by Unit : Not applicable or not available
> Generated by Type : Not applicable or not available
> Message : "type127.dll" was found but did not contain
> any components from the input file.
>
> *** Notice at time : 0.000000
> Generated by Unit : Not applicable or not available
> Generated by Type : Not applicable or not available
> Message : "Type157_demo_release.dll" was found but did
> not contain any components from the input file.
>
> *** Notice at time : 0.000000
> Generated by Unit : Not applicable or not available
> Generated by Type : Not applicable or not available
> Message : "Type76Lib.dll" was found but did not contain
> any components from the input file.
>
> *** Notice at time : 0.000000
> Generated by Unit : Not applicable or not available
> Generated by Type : Not applicable or not available
> Message : "type79-W.dll" was found but did not contain
> any components from the input file.
>
> *** Notice at time : 0.000000
> Generated by Unit : Not applicable or not available
> Generated by Type : Not applicable or not available
> Message : "Type79Lib.dll" was found but did not contain
> any components from the input file.
>
> *** Notice at time : 0.000000
> Generated by Unit : Not applicable or not available
> Generated by Type : Not applicable or not available
> Message : "Type82Lib.dll" was found but did not contain
> any components from the input file.
>
> *** Notice at time : 0.000000
> Generated by Unit : Not applicable or not available
> Generated by Type : Not applicable or not available
> Message : "Type98Lib.dll" was found but did not contain
> any components from the input file.
>
> *** Notice at time : 0.000000
> Generated by Unit : Not applicable or not available
> Generated by Type : Not applicable or not available
> TRNSYS Message 199 : TRNSYS found at least one user DLL in the
> UserLib directory. (Note: Only DLL's including Types that are used in the
> simulation are loaded)
> Reported information : 0 user DLLs were loaded after searching in
> "C:\Trnsys17\UserLib\ReleaseDLLs"
>
>
>
> ------------------------------
> Date: Fri, 29 Aug 2014 14:45:07 +0200
> From: amr.alaaeldin at polimi.it
> To: trnsys-users at lists.onebuilding.org
> CC: trnsys-users at cae.wisc.edu
> Subject: Re: [TRNSYS-users] Trnsys 17 - GenOpt
>
> Dear Ines,
> I have only worked with GenOpt + Trnsys 16... I heard that the steps are
> the same, but I'm not sure...
>
> Where did you get this error message from? I don't think I ever saw such
> an error message...
>
> What I know is that you see the errors in a file called "Genopt.log"...
> Actually it might have a different name, but the extension is ".log".
> If you open this file you can see the error...
>
> Can you please check for that file and let me know if you found it and if
> the error is more clear?
>
> Best of luck,
> Amr
>
>
> On Fri, Aug 29, 2014 at 2:16 PM, Ines Khalifa <khalifa_ines at hotmail.fr>
> wrote:
>
> Dear all,
>
> I am trying to reproduce the example of the document "Using GenOpt with
> Trnsys 16 and Type56" using Trnsys 17. I set the geometry mode at Manual
> since the window height have to be modified by GenOpt. I get the Error
> messages below.
> Any idea about what can be the source of the error ?
>
> Ines
>
>
>
>
> _______________________________________________
> TRNSYS-users mailing list
> TRNSYS-users at lists.onebuilding.org
> http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org
>
>
>
>
> --
> --
> Amr Alaaeldin Elesawy
>
> *PhD Student | Building Engineering*
> *Department of Architecture, Built Environment and Construction
> Engineering (A.B.C.)*
> Politecnico di Milano, Italy
> +39 327 056 0018
>
> _______________________________________________ TRNSYS-users mailing list
> TRNSYS-users at lists.onebuilding.org
> http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org
>
> _______________________________________________
> TRNSYS-users mailing list
> TRNSYS-users at lists.onebuilding.org
> http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org
>
>
> _______________________________________________
> TRNSYS-users mailing list
> TRNSYS-users at lists.onebuilding.org
> http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org
>
>
--
--
Amr Alaaeldin Elesawy
*PhD Student | Building Engineering*
*Department of Architecture, Built Environment and Construction Engineering
(A.B.C.)*
Politecnico di Milano, Italy
+39 327 056 0018
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.onebuilding.org/pipermail/trnsys-users-onebuilding.org/attachments/20140830/56565ffc/attachment-0001.htm>
More information about the TRNSYS-users
mailing list