[TRNSYS-users] .prn files !

[David BRADLEY]

Kostas,
   In general, all of the output files that TRNSYS produces are text 
files. However, the file extension (*.txt, *.dat, *.out, etc.) is 
defined by the user. I am not familiar with the *.prn file extension 
within the TRNSYS (or SketchUp/Trnsys3D) contexts.
Kind regards,
  david


On 6/6/2012 13:32, ts0g . wrote:
>
>
> Dear TRNSYS users,
>
> I have imported a 3d building project which i developed with Google 
> Sketchup 8 ,and i would like to show .prn files as external files 
> after my simulation.
> Which type should i use in order to get this kind of type as an 
> external file ?
>
> Best regards,
> Kostas A. Tsogkas
>
> --Forwarded Message Attachment--
> From: ricardo.palomar at hotmail.com
> To: trnsys-users at cae.wisc.edu
> Date: Wed, 6 Jun 2012 11:03:25 +0000
> Subject: [TRNSYS-users] Type 1716: ROTARY DESICANT DEHUMIDIFIER
>
> Hello !!!
>
> I´m trying to use the type 1716: ROTARY DESICANT DEHUMIDIFIER, but I´m 
> having always the same problem, when I run the simulation the outputs 
> 8 and 12 (Regeneration air relative humidity, 
> and Condensate flow rate) are "0.00". And the outputs 2 and 3 
> (Process air outlet humidity ratio, and Process air 
> outletrelativehumidity) are inconsistent.
>
> Exist any problem running this type?
>
> Thanks !!!
>
>
> --Forwarded Message Attachment--
> From: samir.chehal at ingerop.com
> To: trnsys-users at engr.wisc.edu
> Date: Wed, 6 Jun 2012 14:59:41 +0200
> Subject: [TRNSYS-users] Problem with Type 501
>
> Dear Users,
>
> I must modelize a geothermique pump and I must study the temperature 
> rise at 300m depth.
>
> I connect type 501 with a heat exchanger and I connect this heat 
> exchanger with my heat pump.
>
> The problem is that there are not inputs in type 501 to connect with 
> Hot/Cold side temperature of heat exchanger.
>
> And so I don't know how obtain the rise of temperature in the ground 
> (at 300m depth).
>
> Best regards
>
>
> --Forwarded Message Attachment--
> From: mcdowell at tess-inc.com
> To: trnsys-users at cae.wisc.edu
> Date: Wed, 6 Jun 2012 08:07:23 -0500
> Subject: Re: [TRNSYS-users] Problem with Type 501
>
>
> Samir -
> Type 501 is a ground temperature profile model and not a ground heat 
> exchanger model.  You will need to switch to an actual ground heat 
> exchanger model.
> In the future please only post your question once to the message 
> board. There is no need to repeat the same question over and over.
> Regards,
> Tim
> ---
> Timothy P. McDowell
> Executive Vice President
> Thermal Energy System Specialists, LLC
> 22 N Carroll St, Suite 370
> Madison, WI 53703
> 608-274-2577
> On 2012-06-06 07:59, Samir CHEHAL wrote:
>
>     Dear Users,
>
>     I must modelize a geothermique pump and I must study the
>     temperature rise at 300m depth.
>
>     I connect type 501 with a heat exchanger and I connect this heat
>     exchanger with my heat pump.
>
>     The problem is that there are not inputs in type 501 to connect
>     with Hot/Cold side temperature of heat exchanger.
>
>     And so I don't know how obtain the rise of temperature in the
>     ground (at 300m depth).
>
>     Best regards
>
>
>
> --Forwarded Message Attachment--
> From: antoine.gautier at solamen.fr
> To: trnsys-users at cae.wisc.edu
> Date: Wed, 6 Jun 2012 15:22:16 +0200
> Subject: [TRNSYS-users] Open source version of Type56
>
> Dear users
>
> I cannot find the opensource version of Type56 in my Trnsys 17 package.
>
> Is it still accessible somewhere?
>
> Thanks a lot
>
> --
>
> Antoine Gautier
> SolamenSAS
> +33 6 58 24 02 60
>
> antoine.gautier at solamen.fr
>
>
>
> --Forwarded Message Attachment--
> From: mattia.rio at mail.polimi.it
> To: trnsys-users at cae.wisc.edu
> Date: Wed, 6 Jun 2012 17:11:33 +0200
> Subject: [TRNSYS-users] Shading groups
>
> Hi!!! i have a little problem with my imported 3d model from trnsys 3d
> plug-in for sketchup.
>
> I have posted a picture that show my 3d model in sketchup; so, as you
> can see, all of the triangular surfaces (into red circle), are made in
> perforated corten steel, and i need to give a shading coefficient to
> their, otherwise the  program will do the simulations considering the
> shading surfaces opaque; but actually they are not matt.
>
> if someone have any ideas about how I can do.....
>
> ----------------------------------------------------------------
> This message was sent using IMP, the Internet Messaging Program.
>
>
>
> _______________________________________________
> TRNSYS-users mailing list
> TRNSYS-users at cae.wisc.edu
> https://mailman.cae.wisc.edu/listinfo/trnsys-users

-- 
***************************
David BRADLEY
Principal
Thermal Energy Systems Specialists, LLC
22 North Carroll Street - suite 370
Madison, WI  53703 USA

P:+1.608.274.2577
F:+1.608.278.1475
d.bradley at tess-inc.com

http://www.tess-inc.com
http://www.trnsys.com

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.onebuilding.org/pipermail/trnsys-users-onebuilding.org/attachments/20120606/90bdd4a6/attachment-0005.htm>