[TRNSYS-users] Any Idea about the GenOpt error - "The program could not find all the files. Please check your directory settings"

[Richard Hall]

Thanks Tim for the advice,

It turned out one of my optimisation variables was called 'UnitOverlap' and if you name any variable in the equation editor 'Unit', GenOpt will pick it up in the Error Function Selection and this is the program GenOpt is trying to locate (but obviously can't).

Thanks,
Rich


________________________________
From: Timothy McDowell [mcdowell at tess-inc.com]
Sent: 02 September 2011 19:06
To: Richard Hall; trnsys-users at cae.wisc.edu
Subject: Re: [TRNSYS-users] Any Idea about the GenOpt error - "The program couldnot find all the files. Please check your directory settings"

Richard -

That error means that TrnOpt had an error writing one of the many files that GenOpt uses to run the optimization.  Check that you do not have one of the files open in a different program when you try to run the optimization.

Regards,

Tim




----------------------------------
Timothy McDowell
Executive Vice President
Thermal Energy System Specialists, LLC
22 N. Carroll St, Suite 370
Madison, WI 53703
Phone: 608-274-2577
Fax: 608-278-1475



----- Original Message -----
From: "Richard Hall" <r.hall at steel-sci.com>
Sent: Fri, September 2, 2011 13:02
Subject: [TRNSYS-users] Any Idea about the G enOpt error - "The program couldnot find all the files. Please check your directory settings"


Hi TRNSYS Users,

I have a problem with GenOpt where when I press the 'Run Optimization' button the following error message occurs:

"The program could not find all the files. Please check your directory settings"

I am 90% sure it is not referring to the File Locations (GenOpt, Java and TRNSYS) as GenOpt works fine with the TESS example model. Any ideas about what files it is referring to?

Richard
http://uk.linkedin.com/pub/richard-hall/32/26a/ba2


What I have tried and checked:

 *
The TESS example GenOpt model works;
 *
Correct version of GenOpt and TRNSYS installed;
 *
I have used GenOpt with other models that I have created and it has worked fine;
 *
The simulation of the model works;
 *
Restarting my computer.

Note:The model is reasonable simple but does contain user written components.

________________________________
This transmission is confidential and must not be used or disclosed by anyone other than the intended recipient. The Steel Construction Institute cannot accept any responsibility for any use or misuse of the transmission by anyone.

The Steel Construction Institute is a company limited by guarantee registered in England and Wales under registered number 1916698 and whose registered office is at Silwood Park, Ascot, Berks, SL5 7QN, England. If you have received this message in error, you should not disclose its contents to anyone; please delete it and notify the sender immediately.
________________________________

_______________________________________________
TRNSYS-users mailing list
TRNSYS-users at cae.wisc.edu<http://www.steel-sci.com/owa/UrlBlockedError.aspx>
https://mailman.cae.wisc.edu/listinfo/trnsys-users



________________________________
This transmission is confidential and must not be used or disclosed by anyone other than the intended recipient. The Steel Construction Institute cannot accept any responsibility for any use or misuse of the transmission by anyone.

The Steel Construction Institute is a company limited by guarantee registered in England and Wales under registered number 1916698 and whose registered office is at Silwood Park, Ascot, Berks, SL5 7QN, England. If you have received this message in error, you should not disclose its contents to anyone; please delete it and notify the sender immediately.
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.onebuilding.org/pipermail/trnsys-users-onebuilding.org/attachments/20110903/27580c66/attachment-0001.htm>