[TRNSYS-users] Re : Re : "Range check error"

[jérémie biton]

Hello,

I confirm by testing that the surfaces numbers must not exceed 999 with version 
16.

Regards





________________________________
De : jérémie biton <jeremie_biton at yahoo.fr>
À : Mehdi Shahrestani <mahdishahrestani at yahoo.com>; trnsys-users at cae.wisc.edu
Envoyé le : Lun 11 juillet 2011, 11h 56min 04s
Objet : Re : [TRNSYS-users] "Range check error"



Hi,

I think I found the issue.
I should have mentionned that this project was created with ver 17 from IDF file 
created with google sketch up (all zones at a time). Sorry I didn't think it was 
linked to that.
All 3D information was "broken"and then the project was transfered to ver 16 on 
another computer. This worked well on another project I had.
I think this time, the problem comes from the wall numbering. 
Under TrnBuild, close to "geosurf" information, you have a number, which I think 
is the specific to each wall. In my current project, there are numbers over 
8000, which are apparentlty not supported by ver 16.

Anyone could confirm this last statement?


Regards
Jeremy


________________________________
De : Mehdi Shahrestani <mahdishahrestani at yahoo.com>
À : jérémie biton <jeremie_biton at yahoo.fr>
Envoyé le : Lun 11 juillet 2011, 11h 25min 30s
Objet : RE: [TRNSYS-users] "Range check error"

 
Jeremy 
 
Sorry about that, if I had ver16 I would spend more time to help. 
 
Suggestion: 
Always go step by step in trnsys. Check with lower number of zones for example 
only 2 zones then if it works add more zone. Putting this way ease the process 
of diagnostic. 

 
Hope you solve it. 
Regards
Mehdi
 

________________________________
 
From:jérémie biton [mailto:jeremie_biton at yahoo.fr] 
Sent: 11 July 2011 10:13
To: Mehdi Shahrestani
Subject: Re : [TRNSYS-users] "Range check error"
 
Medhi, 
thanks, it was for sure one of the issues, but it is still not running under 
version 16.

I continue searching

Regards

Jeremy
 

________________________________
 
De :Mehdi Shahrestani <mahdishahrestani at yahoo.com>
À : jérémie biton <jeremie_biton at yahoo.fr>
Envoyé le : Lun 11 juillet 2011, 10h 24min 46s
Objet : RE: [TRNSYS-users] "Range check error"
Jeremy 
 
I am working with ver17. but I tried to get into and found that in zone 09 you 
have additional windows containing 3 windows with very small area 0.00234 m2. 

 
I removed those 3 additional windows from zone 9 and it start to work in my 
version 17.
 
Hope to be a solution
Regards
Mehdi
 

________________________________
 
From:jérémie biton [mailto:jeremie_biton at yahoo.fr] 
Sent: 11 July 2011 08:36
To: Mehdi Shahrestani; trnsys-users at cae.wisc.edu
Subject: Re : [TRNSYS-users] "Range check error"
 
Thanks Mehdi for your answer.
Unfortunatelly I am still stuck. I have only one printer in my project.
It looks the calculation is stopped at time equals to 0.

I re-attached the TPF. Any other guess?

jeremy
 

________________________________
 
De :Mehdi Shahrestani <mahdishahrestani at yahoo.com>
À : jérémie biton <jeremie_biton at yahoo.fr>
Envoyé le : Ven 8 juillet 2011, 18h 28min 15s
Objet : RE: [TRNSYS-users] "Range check error"
Hi Jeremy 
 
I am trnsys user as well. I wanted to open you file but it was only BUI file not 
tpf. 

Anyway, I have had this error couple of times. Check whether you have more than 
10 online plotters. Then check if it runs with run time error equal 1 hr or not. 

 
Hope it helps 
Regards
Mehdi
 

________________________________
 
From:trnsys-users-bounces at cae.wisc.edu 
[mailto:trnsys-users-bounces at cae.wisc.edu] On Behalf Of jérémie biton
Sent: 08 July 2011 16:42
To: trnsys-users at cae.wisc.edu
Subject: [TRNSYS-users] "Range check error"
 

Hello,

I am currently running a 56-type simulation with 85 zones.
When I try to launch the simulation I get the famous "range check error" 
message. I have been checking my model for several hours and this time I am not 
able to solve the issue.

I turned on the debugg mode, but dont get more info and I dont have any fortran 
compiler....
I work with TRNSYS 16.

Any body would be kind enough to have a look?

I attached the INF, TPF and BUI files

Thanks a lot

Regards

Jeremy
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.onebuilding.org/pipermail/trnsys-users-onebuilding.org/attachments/20110711/127be63b/attachment-0005.htm>