[TRNSYS-users] infiltration rate

[王洋]

Dear all,


I want to compare the test room infiltration rate of actual measurement with
by TRNSYS simulation. Maybe as you know, in the TRNFlow manual: there it is
explained that "As soon as TRNFLOW is turned on, (...) in the simulation the
defined infiltrations, ventilations and couplings will be replaced with the
calculated air flows."
I defined CO2% as 1000 ppm in TRNFlow, then I want to observe CO2%'s
reducing curve when infiltration rate is 0.5276 1/h (I measured the value in
the test room), so I defined the infiltration rate as 0.5276 1/h in
TRNBUILD. But when I used TRNFLOW, the defined infiltration rate as 0.5276
1/h in TRNBUILD was replaced. And 1000 ppm keeps constant.

Please tell me  how to get  the infiltration rate curve using TRNSYS/TRNFLOW
or how to explain this ?

Many thanks!

br

wang

2011/2/21 <trnsys-users-request at cae.wisc.edu>

> Send TRNSYS-users mailing list submissions to
>        trnsys-users at cae.wisc.edu
>
> To subscribe or unsubscribe via the World Wide Web, visit
>        https://mailman.cae.wisc.edu/listinfo/trnsys-users
> or, via email, send a message with subject or body 'help' to
>        trnsys-users-request at cae.wisc.edu
>
> You can reach the person managing the list at
>        trnsys-users-owner at cae.wisc.edu
>
> When replying, please edit your Subject line so it is more specific
> than "Re: Contents of TRNSYS-users digest..."
>
> Today's Topics:
>
>   1. Problems with calling EES (Type66a) (Doms Joris)
>   2. wall definition (davide disco)
>
>
> ---------- 已转发邮件 ----------
> From: Doms Joris <joris.doms at vito.be>
> To: "trnsys-users at cae.wisc.edu" <trnsys-users at cae.wisc.edu>
> Date: Sun, 20 Feb 2011 22:43:08 +0100
> Subject: [TRNSYS-users] Problems with calling EES (Type66a)
>  Dear TRNSYS users,
>
> When simulating an applied thermal system, I'm using EES for the hydronic
> part. I programmed the hydronic circuit in EES and coupled it with TRNSYS
> via Type 66a. This coupling works fine, but;
>
> The problem is that the simulation runs very slow. Every timestep that
> TRNSYS calls EES, the EES project is opened and closed. Is there a way to
> set some settings so EES isen't closed and reopened each time, this would
> minimize the solution time alot.
>
> Thanks on advance
>
> Joris Doms
>
>  ------------------------------
> This e-mail, any attachments and the information it contains are
> confidential and meant only for the use of the addressee(s) only.  Access to
> this e-mail by anyone other than the addressee(s) is unauthorized.  If you
> are not the intended addressee (or responsible for delivery of the message
> to such person), you may not use, copy, distribute or deliver to anyone this
> message (or any part of its contents) or take any action in reliance on it.
> In such case, you should destroy this message and notify the sender
> immediately.  If you have received this e-mail in error, please notify us
> immediately by e-mail or telephone and delete the e-mail from any computer.
> All reasonable precautions have been taken to ensure no viruses are present
> in this e-mail and its attachments.  As our company cannot accept
> responsibility for any loss or damage arising from the use of this e-mail or
> attachments we recommend that you subject these to your virus checking
> procedures prior to use.
> ------------------------------
>
>
>
> ---------- 已转发邮件 ----------
> From: davide disco <chester_83 at hotmail.it>
> To: <trnsys-users at cae.wisc.edu>
> Date: Mon, 21 Feb 2011 11:57:59 +0100
> Subject: [TRNSYS-users] wall definition
>  Dear all,
> when entering data in Trnbuild I have to describe the walls of the zone:
> if, looking at the plant of the building, the building has more than a wall
> south oriented for example (wall to the left in the plant) I should enter
> in Trnbuild each section of wall facing south or I should enter a unique
> wall that is the sum of all sections of wall facing south?
> Thanks in advace.
> Best regards
>
> _______________________________________________
> TRNSYS-users mailing list
> TRNSYS-users at cae.wisc.edu
> https://mailman.cae.wisc.edu/listinfo/trnsys-users
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.onebuilding.org/pipermail/trnsys-users-onebuilding.org/attachments/20110221/a0ca382a/attachment-0005.htm>