[TRNSYS-users] TYPE534 Parameters, Error

lucas.lira at scottish-southern.co.uk lucas.lira at scottish-southern.co.uk
Thu Feb 25 01:10:56 PST 2010


Hi Edward. 

The error probably refers to the parameters that you access once you open 
the plug-in. The area where you set the tanks volume, nodes, etc etc. 
I'm not sure what is the parameter 45 but usually this kind of error 
happens when you insert in the plug-in values that make no sense. (for 
example by defining 10 nodes in the tank but placing an outlet at node 11, 
or by creating a too large coil that can't fit in the nodes you placed it 
into).

Take a look if everything there seems reasonable with special attention to 
the outlets/inlets position and, in case of HX inside, if their 
sizes/position make sence.

Hope it helps

Lucas Lira



From:
trnsys-users-request at cae.wisc.edu
To:
trnsys-users at cae.wisc.edu
Date:
25/02/2010 01:17
Subject:
TRNSYS-users Digest, Vol 62, Issue 45



Send TRNSYS-users mailing list submissions to
                 trnsys-users at cae.wisc.edu

To subscribe or unsubscribe via the World Wide Web, visit
                 
https://www-old.cae.wisc.edu/mailman/listinfo/trnsys-users
or, via email, send a message with subject or body 'help' to
                 trnsys-users-request at cae.wisc.edu

You can reach the person managing the list at
                 trnsys-users-owner at cae.wisc.edu

When replying, please edit your Subject line so it is more specific
than "Re: Contents of TRNSYS-users digest..."
Today's Topics:

   1. Re: TYPE534 Parameters, Error (Edward Halawa)

----- Message from Edward Halawa <Edward.Halawa at unisa.edu.au> on Thu, 25 
Feb 2010 11:25:08 +1030 -----
To:
trnsys users <trnsys-users at engr.wisc.edu>
Subject:
Re: [TRNSYS-users] TYPE534 Parameters, Error
Dear All,
 
I managed to replace TYPE 60 with TYPE 534. However, when I run the 
project, the error (see the attachment) appears. As you can see, the error 
message refers to PAR(45). But TYPE 534 only has 5 parameters listed in 
the proforma. (Note: TYPE534 uses plugin and shows another window which 
displays all the parameters such as tank properties, loss etc.)
 
TYPE534 documentation doesn’t help much on this.
 
I appreciate your help. 
 
regards,
edward
 [attachment "Error.bmp" deleted by Lucas Lira/Contractor/SSE] 
_______________________________________________
TRNSYS-users mailing list
TRNSYS-users at cae.wisc.edu
https://www-old.cae.wisc.edu/mailman/listinfo/trnsys-users



**********************************************************************
The information in this e-mail is confidential and may be legally privileged. It may not represent the views of Scottish and Southern Energy Group. It is intended solely for the addressees. Access to this e-mail by anyone else is unauthorised. If you are not the intended recipient, any disclosure, copying, distribution or any action taken or omitted to be taken in reliance on it, is prohibited and may be unlawful. Any unauthorised recipient should advise the sender immediately of the error in transmission. Unless specifically stated otherwise, this email (or any attachments to it) is not an offer capable of acceptance or acceptance of an offer and it does not form part of a binding contractual agreement. Scottish Hydro Electric, Southern Electric, SWALEC, Atlantic Electric and Gas, S+S and SSE Power Distribution are trading names of the Scottish and Southern Energy Group. 
Scottish and Southern Energy plc, Inveralmond House, 200 Dunkeld Road, Perth, Perthshire, PH1 3AQ. Registered in Scotland Number. 117119
**********************************************************************
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.onebuilding.org/pipermail/trnsys-users-onebuilding.org/attachments/20100225/20050140/attachment-0001.htm>


More information about the TRNSYS-users mailing list