[Equest-users] Unmet Heating Hours - ES

[Chris Swanson]

Attached are both the .pd2 & .inp files.  I will look into the
suggestions below in the meantime.

 

Chris Swanson

Roger D. Fields & Associates

(614) 451-2248

 

From: Pasha Korber-Gonzalez [mailto:pasha.pkconsulting at gmail.com] 
Sent: Wednesday, October 20, 2010 2:27 PM
To: Kelsey VanTassel
Cc: Chris Swanson; equest-users at lists.onebuilding.org
Subject: Re: [Equest-users] Unmet Heating Hours - ES

 

It sounds like the heated air is not being allowed to go where there is
a call for conditioning, have you checked your system reports too? it
might have to do with your system & temp scheduling.  Can you send your
.pd2 & .inp file both so that we can open your file in eQuest?

 

thanks,

pkg

On Wed, Oct 20, 2010 at 12:22 PM, Kelsey VanTassel <
KVanTassel at sustaineng.com> wrote:

Make sure that your thermostat type is appropriate. Use Reverse Action
if you want to allow the supply flow in heating mode to rise above the
minimum flow ratio, otherwise use Proportional. Also try reducing the
cool control range from 4 deg to 1 deg.

 

Kelsey Van Tassel

Mechanical Engineer | kvantassel at sustaineng.com

608.836.4488 ext. 20 | Fax: 608.836.4477

 

Sustainable Engineering Group

901 Deming Way, Suite 201

Madison, WI 53717

www.sustaineng.com <http://www.sustaineng.com/> 

 

 

From: equest-users-bounces at lists.onebuilding.org [mailto:
equest-users-bounces at lists.onebuilding.org] On Behalf Of Chris Swanson
Sent: Wednesday, October 20, 2010 1:16 PM
To: equest-users at lists.onebuilding.org
Subject: [Equest-users] Unmet Heating Hours - ES

 

All,

 

I am modeling a two-story elementary school with a VRV / DOAS system in
one area (classrooms, admin.), and a VAV system in another (gym,
cafeteria, food prep.).  The unmet heating hours are currently around
750, and I am at my wit's end to reduce them further.  I have
incorporated suggestions such as increasing the throttling range
(currently at 6, helped a little bit) and sizing ratio (currently at
1.15, although increasing to 2.00 did not help much).  As I have also
tried my best to model the VRV / DOAS system, I'm still not sure if it
is correct...  I've just picked up what I could from the users archives.

 

Does anyone have suggestions for reducing the unmet heating hours that I
may not be aware of?  I have attached the .inp file.  Can anyone see
glaring mistakes in the model?

 

Thanks,

 

Chris Swanson

Mechanical Designer

Roger D. Fields & Associates

Columbus, Ohio 43220-2777

E-mail: cswanson at rdfa.com

 


_______________________________________________
Equest-users mailing list
http://lists.onebuilding.org/listinfo.cgi/equest-users-onebuilding.org
To unsubscribe from this mailing list send  a blank message to 
EQUEST-USERS-UNSUBSCRIBE at ONEBUILDING.ORG

 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.onebuilding.org/pipermail/equest-users-onebuilding.org/attachments/20101020/6766600e/attachment.htm>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: Elementary School - VRV-DOAS-VAV.inp
Type: application/octet-stream
Size: 515461 bytes
Desc: Elementary School - VRV-DOAS-VAV.inp
URL: <http://lists.onebuilding.org/pipermail/equest-users-onebuilding.org/attachments/20101020/6766600e/attachment.obj>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: Elementary School - VRV-DOAS-VAV.pd2
Type: application/octet-stream
Size: 234812 bytes
Desc: Elementary School - VRV-DOAS-VAV.pd2
URL: <http://lists.onebuilding.org/pipermail/equest-users-onebuilding.org/attachments/20101020/6766600e/attachment-0001.obj>