[TRNSYS-users] end of file error

[Angel Carrera]

Suhrid,

assuming that you are using type 53, I think the message does not
necessarily indicates what is the variable out of range, simply, that the
type is getting a COP either too big or too low for the data you defined in
the external performance file. Thus it might be either the temperature
difference, the chiller power or the electrical consumption, wich are the
data you input through the external file, best

Angel
El 11/06/2015 00:23, "Suhrid A Deshmukh" <suhrid at mit.edu> escribió:

>  Hello David,
>
>  I am trying to include a chiller component into my TRNSYS model. Get an
> error that says the Chiller might be operating outside the acceptable
> range. Is this range the range of the cooling loads, the temperatures etc?
> What exactly is it?
>
>  Regards,
> Suhrid
>  ------------------------------
> *From:* David BRADLEY [d.bradley at tess-inc.com]
> *Sent:* Tuesday, June 09, 2015 3:37 PM
> *To:* Suhrid A Deshmukh; TRNSYS users mailing list at OneBuilding.org
> *Subject:* Re: [TRNSYS-users] end of file error
>
>  Suhrid,
>   Type15 rewinds the data file as soon as it gets to the end so it
> *shouldn't* get an "end of file" error unless the file is blank. I'm
> guessing it might be best to send your project to your distributor's
> hotline though since it sounds as though you are getting an end of file
> error when you shouldn't be.
> regards,
>  David
>
>
> On 06/09/2015 13:36, Suhrid A Deshmukh wrote:
>
> Thanks for the prompt response!
> What do you fix if the end of file is happening in type 15-2? It tries to
> read the weather files in the TMY2 format and some of them it reads fine
> and some of them it doesnt.
>
>  Regards,
> Suhrid
>  ------------------------------
> *From:* David BRADLEY [d.bradley at tess-inc.com]
> *Sent:* Tuesday, June 09, 2015 1:22 PM
> *To:* TRNSYS users mailing list at OneBuilding.org; Suhrid A Deshmukh
> *Subject:* Re: [TRNSYS-users] end of file error
>
>  Suhrid,
>  Check to make sure that the 10th parameter of Type51 sets the correct
> number of data points that are in your external file. The default value of
> the 10th parameter is 24. If your data file has less than 24 points in it
> then you'll need to modify the value of that parameter accordingly.
> regards,
>  David
>
>
> On 6/8/2015 10:33 PM, Suhrid A Deshmukh wrote:
>
> Hello all,
> I am trying to simulate a cooling tower Type 51 with an external file and
> the end of file is reached before the simulation ends. Does anyone know the
> fix to this?
>
>  Regards,
> Suhrid
>
>
> _______________________________________________
> TRNSYS-users mailing listTRNSYS-users at lists.onebuilding.orghttp://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org
>
>
> --
> ***************************
> David BRADLEY
> Principal
> Thermal Energy Systems Specialists, LLC
> 22 North Carroll Street - suite 370
> Madison, WI  53703 USA
>
> P:+1.608.274.2577
> F:+1.608.278.1475d.bradley at tess-inc.com
> http://www.tess-inc.comhttp://www.trnsys.com
>
>
> --
> ***************************
> David BRADLEY
> Principal
> Thermal Energy Systems Specialists, LLC
> 22 North Carroll Street - suite 370
> Madison, WI  53703 USA
>
> P:+1.608.274.2577
> F:+1.608.278.1475d.bradley at tess-inc.com
> http://www.tess-inc.comhttp://www.trnsys.com
>
>
> _______________________________________________
> TRNSYS-users mailing list
> TRNSYS-users at lists.onebuilding.org
> http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.onebuilding.org/pipermail/trnsys-users-onebuilding.org/attachments/20150611/ac581b1f/attachment-0002.htm>