<br><font size=2 face="sans-serif">Hello,</font>
<br>
<br><font size=2 face="sans-serif">I have no experience with chilled ceilings,
but as I understand the manual (chapter 6, page 47), the chilled ceiling
layer has to be the first layer (inside surface) in a wall. Or, if you
have an adjacent wall, it can also be the last one (inside surface of the
adjacent zone).</font>
<br>
<br><font size=2 face="sans-serif">I was hoping that someone else with
more experience with chilled ceilings would see your posting and give a
more helpful answer.</font>
<br>
<br>
<br><font size=2 face="sans-serif">Best regards,</font>
<br><font size=2 face="sans-serif">Knut Erik </font>
<br>
<br><font size=2 face="sans-serif"> </font>
<br>
<br>
<br>
<br>
<table width=100%>
<tr valign=top>
<td><font size=1 color=#5f5f5f face="sans-serif">From:</font>
<td><font size=1 face="sans-serif">Mavi Cambronero Vázquez <maviqnk@gmail.com></font>
<tr valign=top>
<td><font size=1 color=#5f5f5f face="sans-serif">To:</font>
<td><font size=1 face="sans-serif">knut.erik.enerstvedt@niva.no</font>
<tr>
<td valign=top><font size=1 color=#5f5f5f face="sans-serif">Cc:</font>
<td><font size=1 face="sans-serif">trnsys-users@cae.wisc.edu</font>
<tr valign=top>
<td><font size=1 color=#5f5f5f face="sans-serif">Date:</font>
<td><font size=1 face="sans-serif">05/13/2010 05:38 PM</font>
<tr valign=top>
<td><font size=1 color=#5f5f5f face="sans-serif">Subject:</font>
<td><font size=1 face="sans-serif">Re: [TRNSYS-users] A lot of convergence
warnings</font></table>
<br>
<hr noshade>
<br>
<br>
<br><font size=3>Thanks for your answers.....</font>
<br><font size=3><br>
I´ve noticed that the problem is the chilled ceiling used. It´s the first
time that I try to use it and I supose I didn´t succeed. I know how to
create a chilled ceiling layer, but I´m not sure what are the following
steps. What I did was integrate the new layer as the last one in a new
wall. TRNBuild said to me that a wall with chilled ceiling can´t be external,
boundary or internal, so the only option is that it is adjacent....
adjacent to the roof???So I created a new zone called roof! I´m a
bit confused.</font>
<br><font size=3> </font>
<br><font size=3>If someone could help me I´d be very grateful!</font>
<br><font size=3> </font>
<br><font size=3>Thanks</font>
<br><font size=3><br>
 </font>
<br><font size=3>2010/4/29 <</font><a href=mailto:knut.erik.enerstvedt@niva.no><font size=3 color=blue><u>knut.erik.enerstvedt@niva.no</u></font></a><font size=3>></font>
<br><font size=2 color=#000080 face="Arial"><br>
In addition to reducing time step length, I would try the following:</font><font size=3>
<br>
</font><font size=2 color=#000080 face="Arial"><br>
- Check if there is sufficient thermal mass in your system (add pipes in
fluid loops, for example).</font><font size=3> </font><font size=2 color=#000080 face="Arial"><br>
- Use controllers (such as Type 2) instead of equations (LT, GT and similar)
when variables that can change from one iteration to the next are involved.</font><font size=3>
</font><font size=2 color=#000080 face="Arial"><br>
- Place components in a "natural" calling order (controllers
before controlled equipment, for example): Control cards->Component
order: Click and drag the different components to order them.</font><font size=3>
</font><font size=2 color=#000080 face="Arial"><br>
- Use an online plotter to check if there are any unrealistic output values
(very high temperatures, for example).</font><font size=3> </font>
<br><font size=2 color=#000080 face="Arial"><br>
Best regards,</font><font size=3> </font><font size=2 color=#000080 face="Arial"><br>
Knut Erik Enerstvedt</font><font size=3> <br>
<br>
<br>
<br>
</font>
<br><font size=2 color=#000080 face="Arial">>You could change the simulation
time step (in steps of 1/(2^n) so 1 hour, 0,5 hour, 0,25 hour etc). You
can find this by assembly -> component >order.</font><font size=3>
</font><font size=2 color=#000080 face="Arial"><br>
 </font><font size=3> </font><font size=2 color=#000080 face="Arial"><br>
>Good luck,</font><font size=3> </font><font size=2 color=#000080 face="Arial"><br>
 </font><font size=3> </font><font size=2 color=#000080 face="Arial"><br>
>Mariëlle Nuchelmans</font><font size=3> </font><font size=3 face="Times New Roman"><br>
 </font><font size=3> </font><font size=3 face="Times New Roman"><br>
 </font><font size=3> </font>
<br><font size=3 face="Times New Roman">>Hi,</font><font size=3> </font><font size=3 face="Times New Roman"><br>
 </font><font size=3> </font><font size=3 face="Times New Roman"><br>
>What can I do when there are lots of convergence problems??? The same
project has different warnigs because of that if the simulation >starts
at 3896 than if it starts at 0.... Does the option "Optimaze component
order" work?? If I select that option other errors appear... :(</font>
<br><font size=2 face="sans-serif"><br>
------------------------------------------------------------------------------------------------------------<br>
Meld deg på vårt nyhetsbrev på </font><a href=http://www.niva.no/ target=_blank><font size=2 color=blue face="sans-serif"><u>www.niva.no</u></font></a>
<br>
<br>
<br><font size=2 face="sans-serif"><br>
------------------------------------------------------------------------------------------------------------<br>
Meld deg på vårt nyhetsbrev på </font><a href=www.niva.no><font size=2 face="sans-serif">www.niva.no</font></a>