<br><font size=2 face="sans-serif">Hello again,</font>
<br>
<br><font size=2 face="sans-serif">I have compared a datafile I have set
up myself based on a particular air cooled chiller model with the sample
data file for Type 655, and it seems like the sample data file is appropriate,
but of course in reversed order. So I think you can safely just swith the
two columns in the sample file so that COP comes first and capacity second.
I think this is also the case for Type 666.</font>
<br>
<br><font size=2 face="sans-serif">Best regards,</font>
<br><font size=2 face="sans-serif">Knut Erik </font>
<br>
<br>
<br>
<table width=100%>
<tr valign=top>
<td><font size=1 color=#5f5f5f face="sans-serif">From:</font>
<td><font size=1 face="sans-serif">a8304506@graduate.hku.hk</font>
<tr valign=top>
<td><font size=1 color=#5f5f5f face="sans-serif">To:</font>
<td><font size=1 face="sans-serif">knut.erik.enerstvedt@niva.no</font>
<tr>
<td valign=top><font size=1 color=#5f5f5f face="sans-serif">Cc:</font>
<td><font size=1 face="sans-serif">trnsys-users@engr.wisc.edu</font>
<tr valign=top>
<td><font size=1 color=#5f5f5f face="sans-serif">Date:</font>
<td><font size=1 face="sans-serif">04/30/2010 03:15 PM</font>
<tr valign=top>
<td><font size=1 color=#5f5f5f face="sans-serif">Subject:</font>
<td><font size=1 face="sans-serif">Re: [TRNSYS-users] Likely bugs in Type655
and Type666</font></table>
<br>
<hr noshade>
<br>
<br>
<br><tt><font size=2>Hello, Knut.<br>
<br>
Thank you for your reply, but do you know if the information indicated
in the<br>
sample data file is appropriate, i.e. the first column is really the capacity<br>
ratio while the second column is the COP ratio.  Your reply is appreciated.<br>
<br>
Best Regards<br>
LEE, Chun Kwong<br>
Division of Building Science and Technology<br>
City University of Hong Kong<br>
<br>
Quoting knut.erik.enerstvedt@niva.no:<br>
<br>
> Hello,<br>
> <br>
> You are absolutely right about this. There is a mismatch between <br>
> documentation and example datafile on one side and source code on
the <br>
> other. The first column in the datafile should consist of COP ratios,
<br>
> while the second column should consist of capacity ratios. There have
been <br>
> some postings about this on the list in the past.<br>
> <br>
> Best regards,<br>
> Knut Erik Enerstvedt<br>
> <br>
>  <br>
> <br>
> >Hello, all.<br>
> <br>
> >I previously developed a parametric model for a water-cooled chiller.
 I <br>
> used it<br>
> >to compare the results with those based on Type666.  I then
found that<br>
> >calculated COP seemed to increase only mildly during the low-load
period <br>
> when<br>
> >using Type666.  I went through the source code and the related
data <br>
> files.  I<br>
> >found that the following statements appeared to be wrong:<br>
> <br>
> >COP_RATIO=Y(1)<br>
> >CAP_RATIO=Y(2)<br>
> <br>
> >According to the data file, the first output should be the capacity
ratio <br>
> while<br>
> >the second output is the COP ratio.  The same case happened
for Type655. <br>
> Am I<br>
> >wrong?<br>
> <br>
> >Best Regards<br>
> >LEE, Chun Kwong<br>
> >Division of Building Science and Technology<br>
> >City University of Hong Kong<br>
><br>
------------------------------------------------------------------------------------------------------------<br>
> Meld deg p?vårt nyhetsbrev p?www.niva.no<br>
<br>
<br>
<br>
<br>
</font></tt>
<br>
<br><font size=2 face="sans-serif"><br>
------------------------------------------------------------------------------------------------------------<br>
Meld deg pa vart nyhetsbrev pa </font><a href=www.niva.no><font size=2 face="sans-serif">www.niva.no</font></a>