[TRNSYS-users] Air-based PVT-Type 50

[Ali Shahrouzian]

Dear David,

Thank you very much. As you mentioned, there are a number of air-based models available in TESS library (such as types 560 and 563), But I guess they are suitable for low-temperature applications. In fact, I need an air based PVT which produces an outlet temperature of at least 100 C. Furthermore, They are unglazed. Do you think types 560 and 563 are applicable for applications with temperature of around 80 - 100 C?
One more question, could I use type 760 as an air to air heat exchanger for high temperature applications, around 80 degrees Celsius.

Best Regards,
Ali

From: David BRADLEY <d.bradley at tess-inc.com>
Sent: May 25, 2021 11:51 AM
To: TRNSYS users mailing list at OneBuilding.org <trnsys-users at lists.onebuilding.org>
Cc: Ali Shahrouzian <ALISHAHROUZIAN at cmail.carleton.ca>
Subject: Re: [TRNSYS-users] Air-based PVT-Type 50

[External Email]

Ali,

 The problem with just changing the fluid specific heat is that the model still won't take into account the impact of the latent heat of vaporization that occurs in air as it passes through the collector. If you're going to approximate an air-based collector using Type50 you at least need to put a psychrometrics component (Type33) after the collector and pass it the collector outlet temperature and the collector's inlet humidity ratio since the absolute humidity won't change across the collector as the working fluid heats up. The Type33 will correct the exiting air state when the collector is heating the working fluid. Correcting the air after calculating the collector performance isn't ideal. You also have to be concerned about flow through the collector when there isn't enough solar energy to heat up the working fluid. If the fluid is cooling down instead of heating up (and it certainly can unless your controls specifically prevent it) and it cools down enough that it drops below the dewpoint temperature then water is going to condense out of the air as it passes through. Again the Type33 will correct the outlet air state and account for the condensation energy but again, it will only correct it after the fact and the correction won't impact the collector's performance.

 A preferable solution would be that if you have access to it there are a number of air-based PV/T models available in the TESS Electrical library

kind regards,

 David


On 05/25/2021 09:05, Ali Shahrouzian via TRNSYS-users wrote:
Hi,

I'm modelling an air-based PVT system for heating application. Do you think I could use the type 50 as an air-based PVT collector if I specify the fluid thermal capacitance of 1 (kJ/kg.K) instead of 4.19?

Thanks in advance



_______________________________________________

TRNSYS-users mailing list

TRNSYS-users at lists.onebuilding.org<mailto:TRNSYS-users at lists.onebuilding.org>

http://lists.onebuilding.org/listinfo.cgi/trnsys-users-onebuilding.org

--

***************************

David BRADLEY

Principal

Thermal Energy Systems Specialists, LLC

3 North Pinckney Street - suite 202

Madison, WI  53703 USA



P:+1.608.274.2577

d.bradley at tess-inc.com<mailto:d.bradley at tess-inc.com>



http://www.tess-inc.com

http://www.trnsys.com

This email contains links to content or websites. Always be cautious when clicking on external links or attachments. If in doubt, please forward suspicious emails to phishing at carleton.ca<mailto:phishing at carleton.ca>.
-----End of Disclaimer-----

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.onebuilding.org/pipermail/trnsys-users-onebuilding.org/attachments/20210525/f85c5749/attachment-0001.html>