<div style="border-width: 1pt medium medium; border-style: solid none none; border-color: rgb(181, 196, 223) -moz-use-text-color -moz-use-text-color; padding: 3pt 0in 0in;"><p class="MsoNormal"><b><span style="font-size: 10pt;">Dear Deepika,</span></b></p>
<p class="MsoNormal"><br><b><span style="font-size: 10pt;"></span></b></p><p class="MsoNormal"><b><span style="font-size: 10pt;">In evaporative cooling where there is no mechanical cooling cycle, the heat gains of the building are absorbed by the evaporatively cooled outside air (with a relatively high RH than outside air). Unlike in mechanical cooling where supply air temperature or flow rate is adjusted to suit the building heat gains (i.e. actual cooling loads), evap coolers have their supply air conditions getting adjusted based on condition of the supply air and the saturation efficiency of the cooler which strongly depends on the supply air flow rate. These systems use large air exchange rates and positive pressure systems which which usually do not get controlled in relations to the building heat gains as in mechanically cooled systems. Thus the impact of the window change will not be present in the "space cooling energy". But any relevant change could be observed in internal space temp & RH values together with change in unmet cooling hours.</span></b></p>
<p class="MsoNormal"><br><b><span style="font-size: 10pt;"></span></b></p><p class="MsoNormal"><b><span style="font-size: 10pt;">This is my understanding on EC systems.<br></span></b></p><p class="MsoNormal"><br><b><span style="font-size: 10pt;"></span></b></p>
<p class="MsoNormal"><b><span style="font-size: 10pt;">Anura</span></b></p><p class="MsoNormal"><b><span style="font-size: 10pt;"><br></span></b></p><p class="MsoNormal"><b><span style="font-size: 10pt;">From:</span></b><span style="font-size: 10pt;"> <a href="mailto:equest-users-bounces@lists.onebuilding.org" target="_blank">equest-users-bounces@lists.onebuilding.org</a> [mailto:<a href="mailto:equest-users-bounces@lists.onebuilding.org" target="_blank">equest-users-bounces@lists.onebuilding.org</a>] <b>On Behalf Of </b>deepika khowal<br>
<b>Sent:</b> Tuesday, August 16, 2011 1:36 PM<br><b>To:</b> <a href="mailto:equest-users@lists.onebuilding.org" target="_blank">equest-users@lists.onebuilding.org</a><br><b>Subject:</b> [Equest-users] evaporative coolers in equest</span></p>
</div><p class="MsoNormal"> </p><p class="MsoNormal">Hello all</p><div><p class="MsoNormal">I am modeling a building in Bridgeport, CA which has evaporative coolers.</p></div><div><p class="MsoNormal">I dont see any benefits if I replace existing clear glass with low-e in cooling energy consumption.</p>
</div><div><p class="MsoNormal">Did anyone model evaporative coolers/swamp coolers before?</p></div><div><p class="MsoNormal">I want to know whether there is a way to show cooling benefit with such HVAC system.</p></div><div>
<p class="MsoNormal">Thanks</p></div><div><p class="MsoNormal">Regards</p></div>Deepika<br><br><div class="gmail_quote">On Thu, Aug 18, 2011 at 2:03 AM,  <span dir="ltr"><<a href="mailto:equest-users-request@lists.onebuilding.org">equest-users-request@lists.onebuilding.org</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="margin: 0pt 0pt 0pt 0.8ex; border-left: 1px solid rgb(204, 204, 204); padding-left: 1ex;">Send Equest-users mailing list submissions to<br>
        <a href="mailto:equest-users@lists.onebuilding.org">equest-users@lists.onebuilding.org</a><br>
<br>
To subscribe or unsubscribe via the World Wide Web, visit<br>
        <a href="http://lists.onebuilding.org/listinfo.cgi/equest-users-onebuilding.org" target="_blank">http://lists.onebuilding.org/listinfo.cgi/equest-users-onebuilding.org</a><br>
<br>
or, via email, send a message with subject or body 'help' to<br>
        <a href="mailto:equest-users-request@lists.onebuilding.org">equest-users-request@lists.onebuilding.org</a><br>
<br>
You can reach the person managing the list at<br>
        <a href="mailto:equest-users-owner@lists.onebuilding.org">equest-users-owner@lists.onebuilding.org</a><br>
<br>
When replying, please edit your Subject line so it is more specific<br>
than "Re: Contents of Equest-users digest..."<br>
<br>Today's Topics:<br>
<br>
   1. Re: evaporative coolers in equest (Nick Caton)<br>
   2. Re: evaporative coolers in equest (Patrick J. O'Leary, Jr.)<br>
   3. Re: evaporative coolers in equest (deepika khowal)<br>
   4. Re: evaporative coolers in equest (Joe Huang)<br>
   5. Re: evaporative coolers in equest (Nick Caton)<br>
   6. Re: evaporative coolers in equest (deepika khowal)<br>
<br><br>---------- Forwarded message ----------<br>From: "Nick Caton" <<a href="mailto:ncaton@smithboucher.com">ncaton@smithboucher.com</a>><br>To: "deepika khowal" <<a href="mailto:deepika.khowal@gmail.com">deepika.khowal@gmail.com</a>><br>
Date: Tue, 16 Aug 2011 16:22:29 -0500<br>Subject: Re: [Equest-users] evaporative coolers in equest<br><div link="blue" vlink="purple" lang="EN-US"><div><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">I hope we’re at a simple vocabulary disconnect here...<u></u><u></u></span></p>
<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><u></u> <u></u></span></p><p><u></u><span style="font-size: 11pt; font-family: Symbol; color: rgb(31, 73, 125);"><span>·<span style="font: 7pt "Times New Roman";">         </span></span></span><u></u><span style="font-size: 11pt; color: rgb(31, 73, 125);">Upgrading the windows will reduce your solar cooling loads.<u></u><u></u></span></p>
<p><u></u><span style="font-size: 11pt; font-family: Symbol; color: rgb(31, 73, 125);"><span>·<span style="font: 7pt "Times New Roman";">         </span></span></span><u></u><span style="font-size: 11pt; color: rgb(31, 73, 125);">Reducing your solar cooling loads will reduce the amount of heat to be removed from the building.<u></u><u></u></span></p>
<p><u></u><span style="font-size: 11pt; font-family: Symbol; color: rgb(31, 73, 125);"><span>·<span style="font: 7pt "Times New Roman";">         </span></span></span><u></u><span style="font-size: 11pt; color: rgb(31, 73, 125);">Reducing the amount of heat to remove will reduce the required hours of operation of your HVAC system (in this case, evaporative coolers) to maintain comfort.<u></u><u></u></span></p>
<p><u></u><span style="font-size: 11pt; font-family: Symbol; color: rgb(31, 73, 125);"><span>·<span style="font: 7pt "Times New Roman";">         </span></span></span><u></u><span style="font-size: 11pt; color: rgb(31, 73, 125);">Reducing the runtime of your evaporative coolers will result in reduced energy consumption.  Fan energies primarily, in the case of evaporative coolers.<u></u><u></u></span></p>
<p><u></u><span style="font-size: 11pt; font-family: Symbol; color: rgb(31, 73, 125);"><span>·<span style="font: 7pt "Times New Roman";">         </span></span></span><u></u><span style="font-size: 11pt; color: rgb(31, 73, 125);">In the event the existing system is not of sufficient capacity to begin with, you may also/instead observe a reduction in unmet cooling hours.<u></u><u></u></span></p>
<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><u></u> <u></u></span></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">The reduction of solar loads with a glazing upgrade could be <i>negligible</i> for a variety of possible reasons, but it’s unlikely the net effect is absolutely zero.  <u></u><u></u></span></p>
<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><u></u> <u></u></span></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">~Nick<u></u><u></u></span></p><p class="MsoNormal">
<span style="font-size: 11pt; color: rgb(31, 73, 125);"><img src="cid:image001.jpg@01CC5C2C.37AD6A50" alt="cid:489575314@22072009-0ABB" width="119" height="37"></span><b><span style="font-size: 11pt; color: rgb(45, 77, 94);"><u></u><u></u></span></b></p>
<p class="MsoNormal"><b><span style="font-size: 11pt; color: rgb(45, 77, 94);"><u></u> <u></u></span></b></p><p class="MsoNormal"><b><span style="color: rgb(45, 77, 94);">NICK CATON, P.E.</span></b><b><span style="color: rgb(45, 77, 94);"><u></u><u></u></span></b></p>
<p class="MsoNormal"><span style="font-size: 7.5pt; color: rgb(204, 153, 0);">SENIOR ENGINEER<u></u><u></u></span></p><p class="MsoNormal"><span style="font-size: 7.5pt; color: rgb(204, 153, 0);"><u></u> <u></u></span></p>
<p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">Smith & Boucher Engineers</span><span style="font-size: 7.5pt; color: rgb(204, 153, 0);"><u></u><u></u></span></p><p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">25501 west valley parkway, suite 200<u></u><u></u></span></p>
<p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">olathe, ks 66061<u></u><u></u></span></p><p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">direct <a href="tel:913.344.0036" value="+19133440036" target="_blank">913.344.0036</a><u></u><u></u></span></p>
<p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">fax <a href="tel:913.345.0617" value="+19133450617" target="_blank">913.345.0617</a><u></u><u></u></span></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><a href="http://www.smithboucher.com" title="blocked::www.smithboucher.com" target="_blank"><span style="font-size: 10pt;">www.smithboucher.com</span></a></span><u><span style="font-size: 10pt; color: blue;"> </span></u><span style="font-size: 11pt; color: rgb(31, 73, 125);"><u></u><u></u></span></p>
<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><u></u> <u></u></span></p><div style="border-width: 1pt medium medium; border-style: solid none none; border-color: rgb(181, 196, 223) -moz-use-text-color -moz-use-text-color; padding: 3pt 0in 0in;">
<p class="MsoNormal"><b><span style="font-size: 10pt;">From:</span></b><span style="font-size: 10pt;"> deepika khowal [mailto:<a href="mailto:deepika.khowal@gmail.com" target="_blank">deepika.khowal@gmail.com</a>] <br><b>Sent:</b> Tuesday, August 16, 2011 3:11 PM<br>
<b>To:</b> Nick Caton<br><b>Cc:</b> <a href="mailto:equest-users@lists.onebuilding.org" target="_blank">equest-users@lists.onebuilding.org</a><br><b>Subject:</b> Re: [Equest-users] evaporative coolers in equest<u></u><u></u></span></p>
</div><p class="MsoNormal"><u></u> <u></u></p><p class="MsoNormal"><u></u> <u></u></p><div><p class="MsoNormal">This is an existing building with evaporative coolers.<u></u><u></u></p></div><div><p class="MsoNormal">the proposed design  to upgrade the windows and check the relative benefits.<u></u><u></u></p>
</div><div><p class="MsoNormal">I dont see much benefits in energy because  evaporative coolers are sized based on Cfm and not btus, the savings will be in cfms.<u></u><u></u></p></div><div><p class="MsoNormal">correct me if I am wrong.<u></u><u></u></p>
</div><div><p class="MsoNormal">is there any other way I can show the benefit in the proposed case if not HVAC benefits?<u></u><u></u></p></div><div><p class="MsoNormal" style="margin-bottom: 12pt;">Thanks<u></u><u></u></p>
<div><p class="MsoNormal">On Tue, Aug 16, 2011 at 1:00 PM, Nick Caton <<a href="mailto:ncaton@smithboucher.com" target="_blank">ncaton@smithboucher.com</a>> wrote:<u></u><u></u></p><div><div><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">Hi Deepika,</span><u></u><u></u></p>
<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">I’m not certain any increase/decrease in cooling loads (such as solar loads affected by changing glazing) should have any effect on the reported “space cooling energy” when you’re using evaporative coolers.  Direct evaporative (swamp) coolers of the simplest sort have only fan and pump energies to consider -  no refrigerant!  I would advise looking up the Detailed Simulation Reports Summary page 158/160 to review end use categories and what they cover. </span><u></u><u></u></p>
<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">I am unfamiliar with Bridgeport’s climate, but as a general rule if I observed a significant amount of glazing in a space served by a direct evaporative cooler… I’d be extra cautious to ensure the HVAC designer is carefully considering condensation and potential for other humidity-driven issues along the way.  I’m most used to seeing them applied to well-ventilated and/or open-air spaces such as garages and gyms/hangars.</span><u></u><u></u></p>
<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">~Nick</span><u></u><u></u></p><p class="MsoNormal">
<span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><img src="cid:image001.jpg@01CC5C2C.37AD6A50" alt="cid:489575314@22072009-0ABB" width="119" border="0" height="37"></span><u></u><u></u></p>
<p class="MsoNormal"><b><span style="font-size: 11pt; color: rgb(45, 77, 94);"> </span></b><u></u><u></u></p><p class="MsoNormal"><b><span style="color: rgb(45, 77, 94);">NICK CATON, P.E.</span></b><u></u><u></u></p><p class="MsoNormal">
<span style="font-size: 7.5pt; color: rgb(204, 153, 0);">SENIOR ENGINEER</span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 7.5pt; color: rgb(204, 153, 0);"> </span><u></u><u></u></p><p class="MsoNormal">
<span style="font-size: 10pt; color: rgb(45, 77, 94);">Smith & Boucher Engineers</span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">25501 west valley parkway, suite 200</span><u></u><u></u></p>
<p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">olathe, ks 66061</span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">direct <a href="tel:913.344.0036" target="_blank">913.344.0036</a></span><u></u><u></u></p>
<p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">fax <a href="tel:913.345.0617" target="_blank">913.345.0617</a></span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><a href="http://www.smithboucher.com" title="blocked::www.smithboucher.com" target="_blank"><span style="font-size: 10pt;">www.smithboucher.com</span></a></span><u><span style="font-size: 10pt; color: blue;"> </span></u><u></u><u></u></p>
<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p><div style="border-width: 1pt medium medium; border-style: solid none none; border-color: rgb(181, 196, 223) -moz-use-text-color -moz-use-text-color; padding: 3pt 0in 0in;">
<p class="MsoNormal"><b><span style="font-size: 10pt;">From:</span></b><span style="font-size: 10pt;"> <a href="mailto:equest-users-bounces@lists.onebuilding.org" target="_blank">equest-users-bounces@lists.onebuilding.org</a> [mailto:<a href="mailto:equest-users-bounces@lists.onebuilding.org" target="_blank">equest-users-bounces@lists.onebuilding.org</a>] <b>On Behalf Of </b>deepika khowal<br>
<b>Sent:</b> Tuesday, August 16, 2011 1:36 PM<br><b>To:</b> <a href="mailto:equest-users@lists.onebuilding.org" target="_blank">equest-users@lists.onebuilding.org</a><br><b>Subject:</b> [Equest-users] evaporative coolers in equest</span><u></u><u></u></p>
</div><div><div><p class="MsoNormal"> <u></u><u></u></p><p class="MsoNormal">Hello all<u></u><u></u></p><div><p class="MsoNormal">I am modeling a building in Bridgeport, CA which has evaporative coolers.<u></u><u></u></p>
</div><div><p class="MsoNormal">I dont see any benefits if I replace existing clear glass with low-e in cooling energy consumption.<u></u><u></u></p></div><div><p class="MsoNormal">Did anyone model evaporative coolers/swamp coolers before?<u></u><u></u></p>
</div><div><p class="MsoNormal">I want to know whether there is a way to show cooling benefit with such HVAC system.<u></u><u></u></p></div><div><p class="MsoNormal">Thanks<u></u><u></u></p></div><div><p class="MsoNormal">
Regards<u></u><u></u></p></div><div><p class="MsoNormal">Deepika<u></u><u></u></p></div></div></div></div></div></div><p class="MsoNormal"><u></u> <u></u></p></div></div></div><br><br>---------- Forwarded message ----------<br>
From: "Patrick J. O'Leary, Jr." <<a href="mailto:poleary1969@gmail.com">poleary1969@gmail.com</a>><br>To: Nick Caton <<a href="mailto:ncaton@smithboucher.com">ncaton@smithboucher.com</a>><br>Date: Tue, 16 Aug 2011 15:47:51 -0700<br>
Subject: Re: [Equest-users] evaporative coolers in equest<br><u></u>


  

<div bgcolor="#ffffff" text="#000000">
i would agree with nick on this except for part #3.  if you're using
ashrae 62, or the 2000/2003/2006 imc (at least the way it is enforced
in southern arizona), the evaporative cooler fan is required to run
while the building is occupied so despite glazing upgrades you
shouldn't be seeing any savings from the hvac system during occupied
hours.  you would probably see some during night setback if the
building there's some thermostat setting that will operate the evap
coolers to remove air (and the associated heat build up) but i would
not think it to be that significant of a savings compared to heat gain
during occupied hours.<br>
<br>
i would think, as nick mentions in point 5, that the ummet cooling
hours might be a better measure of what you are looking for.  improved
glazing should help reduce the rate of heat gain so the evap coolers
should be able to meet whatever setpoint you are using with less unmet
cooling hours.  in reality i would think it would be more obvious by an
occupant working proximity to the windows - if they're currently
affected by the solar heat gain.  i don't know your climate but in
southern arizona you don't really want to be seated right next to a
window with a direct sun exposure and insufficient airflow (evap) or
mechanical cooling and poor windows.<br>
<br>
On 8/16/11 2:22 PM, Nick Caton wrote:
<blockquote type="cite">
  
  

  
  <div>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">I
hope we’re at a simple vocabulary disconnect here...<u></u><u></u></span></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><u></u> <u></u></span></p>
  <p><span style="font-size: 11pt; font-family: Symbol; color: rgb(31, 73, 125);"><span>·<span style="font: 7pt "Times New Roman";">        
  </span></span></span><span style="font-size: 11pt; color: rgb(31, 73, 125);">Upgrading
the windows will reduce your solar cooling loads.<u></u><u></u></span></p>
  <p><span style="font-size: 11pt; font-family: Symbol; color: rgb(31, 73, 125);"><span>·<span style="font: 7pt "Times New Roman";">        
  </span></span></span><span style="font-size: 11pt; color: rgb(31, 73, 125);">Reducing
your solar cooling loads will reduce the amount of heat to be removed
from the building.<u></u><u></u></span></p>
  <p><span style="font-size: 11pt; font-family: Symbol; color: rgb(31, 73, 125);"><span>·<span style="font: 7pt "Times New Roman";">        
  </span></span></span><span style="font-size: 11pt; color: rgb(31, 73, 125);">Reducing
the amount of heat to remove will reduce the required hours of
operation of your HVAC system (in this case, evaporative coolers) to
maintain comfort.<u></u><u></u></span></p>
  <p><span style="font-size: 11pt; font-family: Symbol; color: rgb(31, 73, 125);"><span>·<span style="font: 7pt "Times New Roman";">        
  </span></span></span><span style="font-size: 11pt; color: rgb(31, 73, 125);">Reducing
the runtime of your evaporative coolers will result in reduced energy
consumption.  Fan energies primarily, in the case of evaporative
coolers.<u></u><u></u></span></p>
  <p><span style="font-size: 11pt; font-family: Symbol; color: rgb(31, 73, 125);"><span>·<span style="font: 7pt "Times New Roman";">        
  </span></span></span><span style="font-size: 11pt; color: rgb(31, 73, 125);">In
the event the existing system is not of sufficient capacity to begin
with, you may also/instead observe a reduction in unmet cooling hours.<u></u><u></u></span></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><u></u> <u></u></span></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">The
reduction of solar loads with a glazing upgrade could be <i>negligible</i>
for a variety of possible reasons, but it’s unlikely the net effect is
absolutely zero.  <u></u><u></u></span></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><u></u> <u></u></span></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">~Nick<u></u><u></u></span></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><img src="cid:part1.02090505.02000203@gmail.com" alt="cid:489575314@22072009-0ABB" width="119" height="37"></span><b><span style="font-size: 11pt; color: rgb(45, 77, 94);"><u></u><u></u></span></b></p>

  <p class="MsoNormal"><b><span style="font-size: 11pt; color: rgb(45, 77, 94);"><u></u> <u></u></span></b></p>
  <p class="MsoNormal"><b><span style="color: rgb(45, 77, 94);">NICK
CATON, P.E.</span></b><b><span style="color: rgb(45, 77, 94);"><u></u><u></u></span></b></p>
  <p class="MsoNormal"><span style="font-size: 7.5pt; color: rgb(204, 153, 0);">SENIOR
ENGINEER<u></u><u></u></span></p>
  <p class="MsoNormal"><span style="font-size: 7.5pt; color: rgb(204, 153, 0);"><u></u> <u></u></span></p>
  <p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">Smith
& Boucher Engineers</span><span style="font-size: 7.5pt; color: rgb(204, 153, 0);"><u></u><u></u></span></p>
  <p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">25501
west valley parkway, suite 200<u></u><u></u></span></p>
  <p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">olathe,
ks 66061<u></u><u></u></span></p>
  <p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">direct
<a href="tel:913.344.0036" value="+19133440036" target="_blank">913.344.0036</a><u></u><u></u></span></p>
  <p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">fax
<a href="tel:913.345.0617" value="+19133450617" target="_blank">913.345.0617</a><u></u><u></u></span></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><a href="http://www.smithboucher.com" title="blocked::www.smithboucher.com" target="_blank"><span style="font-size: 10pt;">www.smithboucher.com</span></a></span><u><span style="font-size: 10pt; color: blue;">
  </span></u><span style="font-size: 11pt; color: rgb(31, 73, 125);"><u></u><u></u></span></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><u></u> <u></u></span></p>
  <div style="border-style: solid none none; border-color: rgb(181, 196, 223) -moz-use-text-color -moz-use-text-color; border-width: 1pt medium medium; padding: 3pt 0in 0in;">
  <p class="MsoNormal"><b><span style="font-size: 10pt;">From:</span></b><span style="font-size: 10pt;"> deepika
khowal [<a href="mailto:deepika.khowal@gmail.com" target="_blank">mailto:deepika.khowal@gmail.com</a>] <br>
  <b>Sent:</b> Tuesday, August 16, 2011 3:11 PM<br>
  <b>To:</b> Nick Caton<br>
  <b>Cc:</b> <a href="mailto:equest-users@lists.onebuilding.org" target="_blank">equest-users@lists.onebuilding.org</a><br>
  <b>Subject:</b> Re: [Equest-users] evaporative coolers in equest<u></u><u></u></span></p>
  </div>
  <p class="MsoNormal"><u></u> <u></u></p>
  <p class="MsoNormal"><u></u> <u></u></p>
  <div>
  <p class="MsoNormal">This is an existing building with evaporative
coolers.<u></u><u></u></p>
  </div>
  <div>
  <p class="MsoNormal">the proposed design  to upgrade the windows and
check the relative benefits.<u></u><u></u></p>
  </div>
  <div>
  <p class="MsoNormal">I dont see much benefits in energy because
 evaporative coolers are sized based on Cfm and not btus, the savings
will be in cfms.<u></u><u></u></p>
  </div>
  <div>
  <p class="MsoNormal">correct me if I am wrong.<u></u><u></u></p>
  </div>
  <div>
  <p class="MsoNormal">is there any other way I can show the benefit in
the proposed case if not HVAC benefits?<u></u><u></u></p>
  </div>
  <div>
  <p class="MsoNormal" style="margin-bottom: 12pt;">Thanks<u></u><u></u></p>
  <div>
  <p class="MsoNormal">On Tue, Aug 16, 2011 at 1:00 PM, Nick Caton <<a href="mailto:ncaton@smithboucher.com" target="_blank">ncaton@smithboucher.com</a>>
wrote:<u></u><u></u></p>
  <div>
  <div>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">Hi Deepika,</span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">I’m not certain any
increase/decrease in cooling loads (such as solar loads affected by
changing glazing) should have any effect on the reported “space cooling
energy” when you’re using evaporative coolers.  Direct evaporative
(swamp) coolers of the simplest sort have only fan and pump energies to
consider -  no refrigerant!  I would advise looking up the Detailed
Simulation Reports Summary page 158/160 to review end use categories
and what they cover. </span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">I am unfamiliar with
Bridgeport’s climate, but as a general rule if I observed a significant
amount of glazing in a space served by a direct evaporative cooler… I’d
be extra cautious to ensure the HVAC designer is carefully considering
condensation and potential for other humidity-driven issues along the
way.  I’m most used to seeing them applied to well-ventilated and/or
open-air spaces such as garages and gyms/hangars.</span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">~Nick</span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><img src="cid:part1.02090505.02000203@gmail.com" alt="cid:489575314@22072009-0ABB" width="119" border="0" height="37"></span><u></u><u></u></p>

  <p class="MsoNormal"><b><span style="font-size: 11pt; color: rgb(45, 77, 94);"> </span></b><u></u><u></u></p>
  <p class="MsoNormal"><b><span style="color: rgb(45, 77, 94);">NICK
CATON, P.E.</span></b><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 7.5pt; color: rgb(204, 153, 0);">SENIOR ENGINEER</span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 7.5pt; color: rgb(204, 153, 0);"> </span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">Smith & Boucher
Engineers</span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">25501 west valley
parkway, suite 200</span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">olathe, ks 66061</span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">direct <a href="tel:913.344.0036" target="_blank">913.344.0036</a></span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">fax <a href="tel:913.345.0617" target="_blank">913.345.0617</a></span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><a href="http://www.smithboucher.com" title="blocked::www.smithboucher.com" target="_blank"><span style="font-size: 10pt;">www.smithboucher.com</span></a></span><u><span style="font-size: 10pt; color: blue;"> </span></u><u></u><u></u></p>

  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p>
  <div style="border-style: solid none none; border-color: rgb(181, 196, 223) -moz-use-text-color -moz-use-text-color; border-width: 1pt medium medium; padding: 3pt 0in 0in;">
  <p class="MsoNormal"><b><span style="font-size: 10pt;">From:</span></b><span style="font-size: 10pt;"> <a href="mailto:equest-users-bounces@lists.onebuilding.org" target="_blank">equest-users-bounces@lists.onebuilding.org</a> [mailto:<a href="mailto:equest-users-bounces@lists.onebuilding.org" target="_blank">equest-users-bounces@lists.onebuilding.org</a>] <b>On
Behalf Of </b>deepika khowal<br>
  <b>Sent:</b> Tuesday, August 16, 2011 1:36 PM<br>
  <b>To:</b> <a href="mailto:equest-users@lists.onebuilding.org" target="_blank">equest-users@lists.onebuilding.org</a><br>
  <b>Subject:</b> [Equest-users] evaporative coolers in equest</span><u></u><u></u></p>
  </div>
  <div>
  <div>
  <p class="MsoNormal"> <u></u><u></u></p>
  <p class="MsoNormal">Hello all<u></u><u></u></p>
  <div>
  <p class="MsoNormal">I am modeling a building in Bridgeport,
CA which has evaporative coolers.<u></u><u></u></p>
  </div>
  <div>
  <p class="MsoNormal">I dont see any benefits if I replace
existing clear glass with low-e in cooling energy consumption.<u></u><u></u></p>
  </div>
  <div>
  <p class="MsoNormal">Did anyone model evaporative
coolers/swamp coolers before?<u></u><u></u></p>
  </div>
  <div>
  <p class="MsoNormal">I want to know whether there is a way
to show cooling benefit with such HVAC system.<u></u><u></u></p>
  </div>
  <div>
  <p class="MsoNormal">Thanks<u></u><u></u></p>
  </div>
  <div>
  <p class="MsoNormal">Regards<u></u><u></u></p>
  </div>
  <div>
  <p class="MsoNormal">Deepika<u></u><u></u></p>
  </div>
  </div>
  </div>
  </div>
  </div>
  </div>
  <p class="MsoNormal"><u></u> <u></u></p>
  </div>
  </div>
  <pre><fieldset></fieldset>
_______________________________________________
Equest-users mailing list
<a href="http://lists.onebuilding.org/listinfo.cgi/equest-users-onebuilding.org" target="_blank">http://lists.onebuilding.org/listinfo.cgi/equest-users-onebuilding.org</a>
To unsubscribe from this mailing list send  a blank message to <a href="mailto:EQUEST-USERS-UNSUBSCRIBE@ONEBUILDING.ORG" target="_blank">EQUEST-USERS-UNSUBSCRIBE@ONEBUILDING.ORG</a>
  </pre>
</blockquote>
<br>
</div>

<br><br>---------- Forwarded message ----------<br>From: deepika khowal <<a href="mailto:deepika.khowal@gmail.com">deepika.khowal@gmail.com</a>><br>To: "Patrick J. O'Leary, Jr." <<a href="mailto:poleary1969@gmail.com">poleary1969@gmail.com</a>><br>
Date: Tue, 16 Aug 2011 15:54:12 -0700<br>Subject: Re: [Equest-users] evaporative coolers in equest<br>the building has windows only on south facade.<div>I thk changing the glass type will have impact on unmet hrs.</div><div>
however, I agree that since its diff to have a thermostat control for evaporative coolers during day, the savings are hard to quantify.</div>
<div>Thanks for help.<br><br><div class="gmail_quote">On Tue, Aug 16, 2011 at 3:47 PM, Patrick J. O'Leary, Jr. <span dir="ltr"><<a href="mailto:poleary1969@gmail.com" target="_blank">poleary1969@gmail.com</a>></span> wrote:<br>

<blockquote class="gmail_quote" style="margin: 0pt 0pt 0pt 0.8ex; border-left: 1px solid rgb(204, 204, 204); padding-left: 1ex;"><u></u>


  

<div bgcolor="#ffffff" text="#000000">
i would agree with nick on this except for part #3.  if you're using
ashrae 62, or the 2000/2003/2006 imc (at least the way it is enforced
in southern arizona), the evaporative cooler fan is required to run
while the building is occupied so despite glazing upgrades you
shouldn't be seeing any savings from the hvac system during occupied
hours.  you would probably see some during night setback if the
building there's some thermostat setting that will operate the evap
coolers to remove air (and the associated heat build up) but i would
not think it to be that significant of a savings compared to heat gain
during occupied hours.<br>
<br>
i would think, as nick mentions in point 5, that the ummet cooling
hours might be a better measure of what you are looking for.  improved
glazing should help reduce the rate of heat gain so the evap coolers
should be able to meet whatever setpoint you are using with less unmet
cooling hours.  in reality i would think it would be more obvious by an
occupant working proximity to the windows - if they're currently
affected by the solar heat gain.  i don't know your climate but in
southern arizona you don't really want to be seated right next to a
window with a direct sun exposure and insufficient airflow (evap) or
mechanical cooling and poor windows.<div><div></div><div><br>
<br>
On 8/16/11 2:22 PM, Nick Caton wrote:
</div></div><blockquote type="cite"><div><div></div><div>
  
  

  
  <div>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">I
hope we’re at a simple vocabulary disconnect here...<u></u><u></u></span></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><u></u> <u></u></span></p>
  <p><span style="font-size: 11pt; font-family: Symbol; color: rgb(31, 73, 125);"><span>·<span style="font: 7pt "Times New Roman";">        
  </span></span></span><span style="font-size: 11pt; color: rgb(31, 73, 125);">Upgrading
the windows will reduce your solar cooling loads.<u></u><u></u></span></p>
  <p><span style="font-size: 11pt; font-family: Symbol; color: rgb(31, 73, 125);"><span>·<span style="font: 7pt "Times New Roman";">        
  </span></span></span><span style="font-size: 11pt; color: rgb(31, 73, 125);">Reducing
your solar cooling loads will reduce the amount of heat to be removed
from the building.<u></u><u></u></span></p>
  <p><span style="font-size: 11pt; font-family: Symbol; color: rgb(31, 73, 125);"><span>·<span style="font: 7pt "Times New Roman";">        
  </span></span></span><span style="font-size: 11pt; color: rgb(31, 73, 125);">Reducing
the amount of heat to remove will reduce the required hours of
operation of your HVAC system (in this case, evaporative coolers) to
maintain comfort.<u></u><u></u></span></p>
  <p><span style="font-size: 11pt; font-family: Symbol; color: rgb(31, 73, 125);"><span>·<span style="font: 7pt "Times New Roman";">        
  </span></span></span><span style="font-size: 11pt; color: rgb(31, 73, 125);">Reducing
the runtime of your evaporative coolers will result in reduced energy
consumption.  Fan energies primarily, in the case of evaporative
coolers.<u></u><u></u></span></p>
  <p><span style="font-size: 11pt; font-family: Symbol; color: rgb(31, 73, 125);"><span>·<span style="font: 7pt "Times New Roman";">        
  </span></span></span><span style="font-size: 11pt; color: rgb(31, 73, 125);">In
the event the existing system is not of sufficient capacity to begin
with, you may also/instead observe a reduction in unmet cooling hours.<u></u><u></u></span></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><u></u> <u></u></span></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">The
reduction of solar loads with a glazing upgrade could be <i>negligible</i>
for a variety of possible reasons, but it’s unlikely the net effect is
absolutely zero.  <u></u><u></u></span></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><u></u> <u></u></span></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">~Nick<u></u><u></u></span></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><img src="cid:part1.02090505.02000203@gmail.com" alt="cid:489575314@22072009-0ABB" width="119" height="37"></span><b><span style="font-size: 11pt; color: rgb(45, 77, 94);"><u></u><u></u></span></b></p>


  <p class="MsoNormal"><b><span style="font-size: 11pt; color: rgb(45, 77, 94);"><u></u> <u></u></span></b></p>
  <p class="MsoNormal"><b><span style="color: rgb(45, 77, 94);">NICK
CATON, P.E.</span></b><b><span style="color: rgb(45, 77, 94);"><u></u><u></u></span></b></p>
  <p class="MsoNormal"><span style="font-size: 7.5pt; color: rgb(204, 153, 0);">SENIOR
ENGINEER<u></u><u></u></span></p>
  <p class="MsoNormal"><span style="font-size: 7.5pt; color: rgb(204, 153, 0);"><u></u> <u></u></span></p>
  <p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">Smith
& Boucher Engineers</span><span style="font-size: 7.5pt; color: rgb(204, 153, 0);"><u></u><u></u></span></p>
  <p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">25501
west valley parkway, suite 200<u></u><u></u></span></p>
  <p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">olathe,
ks 66061<u></u><u></u></span></p>
  <p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">direct
<a href="tel:913.344.0036" value="+19133440036" target="_blank">913.344.0036</a><u></u><u></u></span></p>
  <p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">fax
<a href="tel:913.345.0617" value="+19133450617" target="_blank">913.345.0617</a><u></u><u></u></span></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><a href="http://www.smithboucher.com" title="blocked::www.smithboucher.com" target="_blank"><span style="font-size: 10pt;">www.smithboucher.com</span></a></span><u><span style="font-size: 10pt; color: blue;">
  </span></u><span style="font-size: 11pt; color: rgb(31, 73, 125);"><u></u><u></u></span></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><u></u> <u></u></span></p>
  <div style="border-style: solid none none; border-color: rgb(181, 196, 223) -moz-use-text-color -moz-use-text-color; border-width: 1pt medium medium; padding: 3pt 0in 0in;">
  <p class="MsoNormal"><b><span style="font-size: 10pt;">From:</span></b><span style="font-size: 10pt;"> deepika
khowal [<a href="mailto:deepika.khowal@gmail.com" target="_blank">mailto:deepika.khowal@gmail.com</a>] <br>
  <b>Sent:</b> Tuesday, August 16, 2011 3:11 PM<br>
  <b>To:</b> Nick Caton<br>
  <b>Cc:</b> <a href="mailto:equest-users@lists.onebuilding.org" target="_blank">equest-users@lists.onebuilding.org</a><br>
  <b>Subject:</b> Re: [Equest-users] evaporative coolers in equest<u></u><u></u></span></p>
  </div>
  <p class="MsoNormal"><u></u> <u></u></p>
  <p class="MsoNormal"><u></u> <u></u></p>
  <div>
  <p class="MsoNormal">This is an existing building with evaporative
coolers.<u></u><u></u></p>
  </div>
  <div>
  <p class="MsoNormal">the proposed design  to upgrade the windows and
check the relative benefits.<u></u><u></u></p>
  </div>
  <div>
  <p class="MsoNormal">I dont see much benefits in energy because
 evaporative coolers are sized based on Cfm and not btus, the savings
will be in cfms.<u></u><u></u></p>
  </div>
  <div>
  <p class="MsoNormal">correct me if I am wrong.<u></u><u></u></p>
  </div>
  <div>
  <p class="MsoNormal">is there any other way I can show the benefit in
the proposed case if not HVAC benefits?<u></u><u></u></p>
  </div>
  <div>
  <p class="MsoNormal" style="margin-bottom: 12pt;">Thanks<u></u><u></u></p>
  <div>
  <p class="MsoNormal">On Tue, Aug 16, 2011 at 1:00 PM, Nick Caton <<a href="mailto:ncaton@smithboucher.com" target="_blank">ncaton@smithboucher.com</a>>
wrote:<u></u><u></u></p>
  <div>
  <div>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">Hi Deepika,</span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">I’m not certain any
increase/decrease in cooling loads (such as solar loads affected by
changing glazing) should have any effect on the reported “space cooling
energy” when you’re using evaporative coolers.  Direct evaporative
(swamp) coolers of the simplest sort have only fan and pump energies to
consider -  no refrigerant!  I would advise looking up the Detailed
Simulation Reports Summary page 158/160 to review end use categories
and what they cover. </span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">I am unfamiliar with
Bridgeport’s climate, but as a general rule if I observed a significant
amount of glazing in a space served by a direct evaporative cooler… I’d
be extra cautious to ensure the HVAC designer is carefully considering
condensation and potential for other humidity-driven issues along the
way.  I’m most used to seeing them applied to well-ventilated and/or
open-air spaces such as garages and gyms/hangars.</span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">~Nick</span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><img src="cid:part1.02090505.02000203@gmail.com" alt="cid:489575314@22072009-0ABB" width="119" border="0" height="37"></span><u></u><u></u></p>

  <p class="MsoNormal"><b><span style="font-size: 11pt; color: rgb(45, 77, 94);"> </span></b><u></u><u></u></p>
  <p class="MsoNormal"><b><span style="color: rgb(45, 77, 94);">NICK
CATON, P.E.</span></b><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 7.5pt; color: rgb(204, 153, 0);">SENIOR ENGINEER</span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 7.5pt; color: rgb(204, 153, 0);"> </span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">Smith & Boucher
Engineers</span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">25501 west valley
parkway, suite 200</span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">olathe, ks 66061</span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">direct <a href="tel:913.344.0036" target="_blank">913.344.0036</a></span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">fax <a href="tel:913.345.0617" target="_blank">913.345.0617</a></span><u></u><u></u></p>
  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><a href="http://www.smithboucher.com" title="blocked::www.smithboucher.com" target="_blank"><span style="font-size: 10pt;">www.smithboucher.com</span></a></span><u><span style="font-size: 10pt; color: blue;"> </span></u><u></u><u></u></p>


  <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p>
  <div style="border-style: solid none none; border-color: rgb(181, 196, 223) -moz-use-text-color -moz-use-text-color; border-width: 1pt medium medium; padding: 3pt 0in 0in;">
  <p class="MsoNormal"><b><span style="font-size: 10pt;">From:</span></b><span style="font-size: 10pt;"> <a href="mailto:equest-users-bounces@lists.onebuilding.org" target="_blank">equest-users-bounces@lists.onebuilding.org</a> [mailto:<a href="mailto:equest-users-bounces@lists.onebuilding.org" target="_blank">equest-users-bounces@lists.onebuilding.org</a>] <b>On
Behalf Of </b>deepika khowal<br>
  <b>Sent:</b> Tuesday, August 16, 2011 1:36 PM<br>
  <b>To:</b> <a href="mailto:equest-users@lists.onebuilding.org" target="_blank">equest-users@lists.onebuilding.org</a><br>
  <b>Subject:</b> [Equest-users] evaporative coolers in equest</span><u></u><u></u></p>
  </div>
  <div>
  <div>
  <p class="MsoNormal"> <u></u><u></u></p>
  <p class="MsoNormal">Hello all<u></u><u></u></p>
  <div>
  <p class="MsoNormal">I am modeling a building in Bridgeport,
CA which has evaporative coolers.<u></u><u></u></p>
  </div>
  <div>
  <p class="MsoNormal">I dont see any benefits if I replace
existing clear glass with low-e in cooling energy consumption.<u></u><u></u></p>
  </div>
  <div>
  <p class="MsoNormal">Did anyone model evaporative
coolers/swamp coolers before?<u></u><u></u></p>
  </div>
  <div>
  <p class="MsoNormal">I want to know whether there is a way
to show cooling benefit with such HVAC system.<u></u><u></u></p>
  </div>
  <div>
  <p class="MsoNormal">Thanks<u></u><u></u></p>
  </div>
  <div>
  <p class="MsoNormal">Regards<u></u><u></u></p>
  </div>
  <div>
  <p class="MsoNormal">Deepika<u></u><u></u></p>
  </div>
  </div>
  </div>
  </div>
  </div>
  </div>
  <p class="MsoNormal"><u></u> <u></u></p>
  </div>
  </div>
  </div></div><pre><fieldset></fieldset>
_______________________________________________
Equest-users mailing list
<div><a href="http://lists.onebuilding.org/listinfo.cgi/equest-users-onebuilding.org" target="_blank">http://lists.onebuilding.org/listinfo.cgi/equest-users-onebuilding.org</a>
To unsubscribe from this mailing list send  a blank message to <a href="mailto:EQUEST-USERS-UNSUBSCRIBE@ONEBUILDING.ORG" target="_blank">EQUEST-USERS-UNSUBSCRIBE@ONEBUILDING.ORG</a>
  </div></pre>
</blockquote>
<br>
</div>

</blockquote></div><br></div>
<br><br>---------- Forwarded message ----------<br>From: Joe Huang <<a href="mailto:yjhuang@whiteboxtechnologies.com">yjhuang@whiteboxtechnologies.com</a>><br>To: <a href="mailto:equest-users@lists.onebuilding.org">equest-users@lists.onebuilding.org</a><br>
Date: Tue, 16 Aug 2011 17:13:04 -0700<br>Subject: Re: [Equest-users] evaporative coolers in equest<br><u></u>

  
    
  
  <div text="#000000" bgcolor="#ffffff">
    This is the wrong way to look at evap cooling performance.  In fact,
    the whole logic of sizing using design conditions falls apart when
    it comes to evap coolers.  Evaporative cooling works by taking
    advantage of the wet-bulb depression to trade off latent for
    sensible heat. <br>
    When the wet-bulb depression (DBT - WBT) is low or when the WBT is
    high, evap cooling<br>
    will provide little cooling.  A better way to size evap cooling is
    to either minimize the unmet<br>
    cooling hours, or if there is an AC backup, maximize the energy
    reductions.<br>
    <br>
    If you're working with a fixed evap cooling size, then you should
    look at the number of unmet cooling hours to see the benefits of a
    window upgrade, as well as the reduction (if any) of  electricity
    use.<br>
    <br>
    Joe<br>
    <pre cols="90">Joe Huang
White Box Technologies, Inc.
346 Rheem Blvd., Suite 108D
Moraga CA 94556
<a href="mailto:yjhuang@whiteboxtechnologies.com" target="_blank">yjhuang@whiteboxtechnologies.com</a>
<a href="http://www.whiteboxtechnologies.com" target="_blank">www.whiteboxtechnologies.com</a>
(o) <a href="tel:%28925%29388-0265" value="+19253880265" target="_blank">(925)388-0265</a>
(c) <a href="tel:%28510%29928-2683" value="+15109282683" target="_blank">(510)928-2683</a>
"building energy simulations at your fingertips"
</pre>
    <br>
    On 8/16/2011 1:11 PM, deepika khowal wrote:
    <blockquote type="cite"><br>
      <div>This is an existing building with evaporative coolers.</div>
      <div>the proposed design  to upgrade the windows and check the
        relative benefits.</div>
      <div>I dont see much benefits in energy because  evaporative
        coolers are sized based on Cfm and not btus, the savings will be
        in cfms.</div>
      <div>correct me if I am wrong.</div>
      <div>is there any other way I can show the benefit in the proposed
        case if not HVAC benefits?</div>
      <div>Thanks<br>
        <br>
        <div class="gmail_quote">On Tue, Aug 16, 2011 at 1:00 PM, Nick
          Caton <span dir="ltr"><<a href="mailto:ncaton@smithboucher.com" target="_blank">ncaton@smithboucher.com</a>></span>
          wrote:<br>
          <blockquote class="gmail_quote" style="margin: 0pt 0pt 0pt 0.8ex; border-left: 1px solid rgb(204, 204, 204); padding-left: 1ex;">
            <div link="blue" vlink="purple" lang="EN-US">
              <div>
                <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">Hi Deepika,</span></p>
                <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span></p>
                <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">I’m not certain any
                    increase/decrease in cooling loads (such as solar
                    loads affected by changing glazing) should have any
                    effect on the reported “space cooling energy” when
                    you’re using evaporative coolers.  Direct
                    evaporative (swamp) coolers of the simplest sort
                    have only fan and pump energies to consider -  no
                    refrigerant!  I would advise looking up the Detailed
                    Simulation Reports Summary page 158/160 to review
                    end use categories and what they cover. </span></p>
                <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span></p>
                <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">I am unfamiliar with
                    Bridgeport’s climate, but as a general rule if I
                    observed a significant amount of glazing in a space
                    served by a direct evaporative cooler… I’d be extra
                    cautious to ensure the HVAC designer is carefully
                    considering condensation and potential for other
                    humidity-driven issues along the way.  I’m most used
                    to seeing them applied to well-ventilated and/or
                    open-air spaces such as garages and gyms/hangars.</span></p>
                <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span></p>
                <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">~Nick</span></p>
                <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span></p>
                <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><img src="cid:part1.05050303.02060803@whiteboxtechnologies.com" alt="cid:489575314@22072009-0ABB" width="119" height="37"></span><b><span style="font-size: 11pt; color: rgb(45, 77, 94);"></span></b></p>

                <p class="MsoNormal"><b><span style="font-size: 11pt; color: rgb(45, 77, 94);"> </span></b></p>
                <p class="MsoNormal"><b><span style="color: rgb(45, 77, 94);">NICK CATON, P.E.</span></b><b><span style="color: rgb(45, 77, 94);"></span></b></p>
                <p class="MsoNormal"><span style="font-size: 7.5pt; color: rgb(204, 153, 0);">SENIOR ENGINEER</span></p>
                <p class="MsoNormal"><span style="font-size: 7.5pt; color: rgb(204, 153, 0);"> </span></p>
                <p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">Smith & Boucher
                    Engineers</span><span style="font-size: 7.5pt; color: rgb(204, 153, 0);"></span></p>
                <p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">25501 west valley parkway,
                    suite 200</span></p>
                <p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">olathe, ks 66061</span></p>
                <p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">direct <a href="tel:913.344.0036" value="+19133440036" target="_blank">913.344.0036</a></span></p>
                <p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">fax <a href="tel:913.345.0617" value="+19133450617" target="_blank">913.345.0617</a></span></p>
                <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><a href="http://www.smithboucher.com" title="blocked::www.smithboucher.com" target="_blank"><span style="font-size: 10pt; color: blue;">www.smithboucher.com</span></a></span><u><span style="font-size: 10pt; color: blue;"> </span></u><span style="font-size: 11pt; color: rgb(31, 73, 125);"></span></p>

                <p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span></p>
                <div style="border-width: 1pt medium medium; border-style: solid none none; border-color: rgb(181, 196, 223) -moz-use-text-color -moz-use-text-color; padding: 3pt 0in 0in;">
                  <p class="MsoNormal"><b><span style="font-size: 10pt;">From:</span></b><span style="font-size: 10pt;"> <a href="mailto:equest-users-bounces@lists.onebuilding.org" target="_blank">equest-users-bounces@lists.onebuilding.org</a>
                      [mailto:<a href="mailto:equest-users-bounces@lists.onebuilding.org" target="_blank">equest-users-bounces@lists.onebuilding.org</a>]
                      <b>On Behalf Of </b>deepika khowal<br>
                      <b>Sent:</b> Tuesday, August 16, 2011 1:36 PM<br>
                      <b>To:</b> <a href="mailto:equest-users@lists.onebuilding.org" target="_blank">equest-users@lists.onebuilding.org</a><br>
                      <b>Subject:</b> [Equest-users] evaporative coolers
                      in equest</span></p>
                </div>
                <div>
                  <div>
                    <p class="MsoNormal"> </p>
                    <p class="MsoNormal">Hello all</p>
                    <div>
                      <p class="MsoNormal">I am modeling a building in
                        Bridgeport, CA which has evaporative coolers.</p>
                    </div>
                    <div>
                      <p class="MsoNormal">I dont see any benefits if I
                        replace existing clear glass with low-e in
                        cooling energy consumption.</p>
                    </div>
                    <div>
                      <p class="MsoNormal">Did anyone model evaporative
                        coolers/swamp coolers before?</p>
                    </div>
                    <div>
                      <p class="MsoNormal">I want to know whether there
                        is a way to show cooling benefit with such HVAC
                        system.</p>
                    </div>
                    <div>
                      <p class="MsoNormal">Thanks</p>
                    </div>
                    <div>
                      <p class="MsoNormal">
                        Regards</p>
                    </div>
                    <div>
                      <p class="MsoNormal">Deepika</p>
                    </div>
                  </div>
                </div>
              </div>
            </div>
          </blockquote>
        </div>
        <br>
      </div>
      <pre><fieldset></fieldset>
_______________________________________________
Equest-users mailing list
<a href="http://lists.onebuilding.org/listinfo.cgi/equest-users-onebuilding.org" target="_blank">http://lists.onebuilding.org/listinfo.cgi/equest-users-onebuilding.org</a>
To unsubscribe from this mailing list send  a blank message to <a href="mailto:EQUEST-USERS-UNSUBSCRIBE@ONEBUILDING.ORG" target="_blank">EQUEST-USERS-UNSUBSCRIBE@ONEBUILDING.ORG</a>
</pre>
    </blockquote>
  </div>

<br><br>---------- Forwarded message ----------<br>From: "Nick Caton" <<a href="mailto:ncaton@smithboucher.com">ncaton@smithboucher.com</a>><br>To: "Patrick J. O'Leary, Jr." <<a href="mailto:poleary1969@gmail.com">poleary1969@gmail.com</a>><br>
Date: Wed, 17 Aug 2011 09:56:18 -0500<br>Subject: Re: [Equest-users] evaporative coolers in equest<br><div bgcolor="white" link="blue" vlink="purple" lang="EN-US"><div><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">Patrick, thanks for the heads up!<u></u><u></u></span></p>
<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><u></u> <u></u></span></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">My experience applying evap. coolers has been on a limited basis explicitly for space comfort, operated staged & cycled off via thermostat, so my brainstorming for Deepika was tailored to my past experience.  In those cases (auto garages), a mechanical ventilation system was provided as an entirely separate system, so the 62.1/IMC requirements for ventilation during occupancy were addressed elsewhere.<u></u><u></u></span></p>
<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><u></u> <u></u></span></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">If one is in fact using a swamp cooler functionally to supply required ventilation air, then I would agree it makes complete sense to operate continuously during occupied hours.  <u></u><u></u></span></p>
<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><u></u> <u></u></span></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">I recall evap. coolers being a breath of fresh air (har har) to design around as they do make you rethink how you use your psych charts =).  I’ll defer any specific swamp cooler application queries to the Arizona engineer below me though – we don’t use them quite so often locally, outside of the desert ;).<u></u><u></u></span></p>
<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><u></u> <u></u></span></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">~Nick<u></u><u></u></span></p><p class="MsoNormal">
<span style="font-size: 11pt; color: rgb(31, 73, 125);"><u></u> <u></u></span></p><div><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><img src="cid:image001.jpg@01CC5CBB.C8A46B00" alt="cid:489575314@22072009-0ABB" width="119" height="37"></span><b><span style="font-size: 11pt; color: rgb(45, 77, 94);"><u></u><u></u></span></b></p>
<p class="MsoNormal"><b><span style="font-size: 11pt; color: rgb(45, 77, 94);"><u></u> <u></u></span></b></p><p class="MsoNormal"><b><span style="color: rgb(45, 77, 94);">NICK CATON, P.E.</span></b><b><span style="color: rgb(45, 77, 94);"><u></u><u></u></span></b></p>
<p class="MsoNormal"><span style="font-size: 7.5pt; color: rgb(204, 153, 0);">SENIOR ENGINEER<u></u><u></u></span></p><p class="MsoNormal"><span style="font-size: 7.5pt; color: rgb(204, 153, 0);"><u></u> <u></u></span></p>
<p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">Smith & Boucher Engineers</span><span style="font-size: 7.5pt; color: rgb(204, 153, 0);"><u></u><u></u></span></p><p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">25501 west valley parkway, suite 200<u></u><u></u></span></p>
<p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">olathe, ks 66061<u></u><u></u></span></p><p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">direct <a href="tel:913.344.0036" value="+19133440036" target="_blank">913.344.0036</a><u></u><u></u></span></p>
<p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">fax <a href="tel:913.345.0617" value="+19133450617" target="_blank">913.345.0617</a><u></u><u></u></span></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><a href="http://www.smithboucher.com" title="blocked::www.smithboucher.com" target="_blank"><span style="font-size: 10pt;">www.smithboucher.com</span></a></span><u><span style="font-size: 10pt; color: blue;"> </span></u><span style="font-size: 11pt; color: rgb(31, 73, 125);"><u></u><u></u></span></p>
</div><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><u></u> <u></u></span></p><div><div style="border-width: 1pt medium medium; border-style: solid none none; border-color: rgb(181, 196, 223) -moz-use-text-color -moz-use-text-color; padding: 3pt 0in 0in;">
<p class="MsoNormal"><b><span style="font-size: 10pt; color: windowtext;">From:</span></b><span style="font-size: 10pt; color: windowtext;"> Patrick J. O'Leary, Jr. [mailto:<a href="mailto:poleary1969@gmail.com" target="_blank">poleary1969@gmail.com</a>] <br>
<b>Sent:</b> Tuesday, August 16, 2011 5:48 PM<br><b>To:</b> Nick Caton<br><b>Cc:</b> deepika khowal; <a href="mailto:equest-users@lists.onebuilding.org" target="_blank">equest-users@lists.onebuilding.org</a><br><b>Subject:</b> Re: [Equest-users] evaporative coolers in equest<u></u><u></u></span></p>
</div></div><p class="MsoNormal"><u></u> <u></u></p><p class="MsoNormal">i would agree with nick on this except for part #3.  if you're using ashrae 62, or the 2000/2003/2006 imc (at least the way it is enforced in southern arizona), the evaporative cooler fan is required to run while the building is occupied so despite glazing upgrades you shouldn't be seeing any savings from the hvac system during occupied hours.  you would probably see some during night setback if the building there's some thermostat setting that will operate the evap coolers to remove air (and the associated heat build up) but i would not think it to be that significant of a savings compared to heat gain during occupied hours.<br>
<br>i would think, as nick mentions in point 5, that the ummet cooling hours might be a better measure of what you are looking for.  improved glazing should help reduce the rate of heat gain so the evap coolers should be able to meet whatever setpoint you are using with less unmet cooling hours.  in reality i would think it would be more obvious by an occupant working proximity to the windows - if they're currently affected by the solar heat gain.  i don't know your climate but in southern arizona you don't really want to be seated right next to a window with a direct sun exposure and insufficient airflow (evap) or mechanical cooling and poor windows.<br>
<br>On 8/16/11 2:22 PM, Nick Caton wrote: <u></u><u></u></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">I hope we’re at a simple vocabulary disconnect here...</span><u></u><u></u></p><p class="MsoNormal">
<span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p><p><span style="font-size: 11pt; color: rgb(31, 73, 125);">Upgrading the windows will reduce your solar cooling loads.</span><u></u><u></u></p>
<p><span style="font-size: 11pt; color: rgb(31, 73, 125);">Reducing your solar cooling loads will reduce the amount of heat to be removed from the building.</span><u></u><u></u></p><p><span style="font-size: 11pt; color: rgb(31, 73, 125);">Reducing the amount of heat to remove will reduce the required hours of operation of your HVAC system (in this case, evaporative coolers) to maintain comfort.</span><u></u><u></u></p>
<p><span style="font-size: 11pt; color: rgb(31, 73, 125);">Reducing the runtime of your evaporative coolers will result in reduced energy consumption.  Fan energies primarily, in the case of evaporative coolers.</span><u></u><u></u></p>
<p><span style="font-size: 11pt; color: rgb(31, 73, 125);">In the event the existing system is not of sufficient capacity to begin with, you may also/instead observe a reduction in unmet cooling hours.</span><u></u><u></u></p>
<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">The reduction of solar loads with a glazing upgrade could be <i>negligible</i> for a variety of possible reasons, but it’s unlikely the net effect is absolutely zero.  </span><u></u><u></u></p>
<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">~Nick</span><u></u><u></u></p><p class="MsoNormal">
<span style="font-size: 11pt; color: rgb(31, 73, 125);"><img src="cid:image001.jpg@01CC5CBB.C8A46B00" alt="cid:489575314@22072009-0ABB" width="119" border="0" height="37"></span><u></u><u></u></p><p class="MsoNormal"><b><span style="font-size: 11pt; color: rgb(45, 77, 94);"> </span></b><u></u><u></u></p>
<p class="MsoNormal"><b><span style="color: rgb(45, 77, 94);">NICK CATON, P.E.</span></b><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 7.5pt; color: rgb(204, 153, 0);">SENIOR ENGINEER</span><u></u><u></u></p>
<p class="MsoNormal"><span style="font-size: 7.5pt; color: rgb(204, 153, 0);"> </span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">Smith & Boucher Engineers</span><u></u><u></u></p>
<p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">25501 west valley parkway, suite 200</span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">olathe, ks 66061</span><u></u><u></u></p>
<p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">direct <a href="tel:913.344.0036" value="+19133440036" target="_blank">913.344.0036</a></span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">fax <a href="tel:913.345.0617" value="+19133450617" target="_blank">913.345.0617</a></span><u></u><u></u></p>
<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><a href="http://www.smithboucher.com" title="blocked::www.smithboucher.com" target="_blank"><span style="font-size: 10pt;">www.smithboucher.com</span></a></span><u><span style="font-size: 10pt; color: blue;"> </span></u><u></u><u></u></p>
<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p><div style="border-width: 1pt medium medium; border-style: solid none none; padding: 3pt 0in 0in; border-color: -moz-use-text-color;">
<p class="MsoNormal"><b><span style="font-size: 10pt;">From:</span></b><span style="font-size: 10pt;"> deepika khowal [<a href="mailto:deepika.khowal@gmail.com" target="_blank">mailto:deepika.khowal@gmail.com</a>] <br><b>Sent:</b> Tuesday, August 16, 2011 3:11 PM<br>
<b>To:</b> Nick Caton<br><b>Cc:</b> <a href="mailto:equest-users@lists.onebuilding.org" target="_blank">equest-users@lists.onebuilding.org</a><br><b>Subject:</b> Re: [Equest-users] evaporative coolers in equest</span><u></u><u></u></p>
</div><p class="MsoNormal"> <u></u><u></u></p><p class="MsoNormal"> <u></u><u></u></p><div><p class="MsoNormal">This is an existing building with evaporative coolers.<u></u><u></u></p></div><div><p class="MsoNormal">the proposed design  to upgrade the windows and check the relative benefits.<u></u><u></u></p>
</div><div><p class="MsoNormal">I dont see much benefits in energy because  evaporative coolers are sized based on Cfm and not btus, the savings will be in cfms.<u></u><u></u></p></div><div><p class="MsoNormal">correct me if I am wrong.<u></u><u></u></p>
</div><div><p class="MsoNormal">is there any other way I can show the benefit in the proposed case if not HVAC benefits?<u></u><u></u></p></div><div><p class="MsoNormal" style="margin-bottom: 12pt;">Thanks<u></u><u></u></p>
<div><p class="MsoNormal">On Tue, Aug 16, 2011 at 1:00 PM, Nick Caton <<a href="mailto:ncaton@smithboucher.com" target="_blank">ncaton@smithboucher.com</a>> wrote:<u></u><u></u></p><div><div><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">Hi Deepika,</span><u></u><u></u></p>
<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">I’m not certain any increase/decrease in cooling loads (such as solar loads affected by changing glazing) should have any effect on the reported “space cooling energy” when you’re using evaporative coolers.  Direct evaporative (swamp) coolers of the simplest sort have only fan and pump energies to consider -  no refrigerant!  I would advise looking up the Detailed Simulation Reports Summary page 158/160 to review end use categories and what they cover. </span><u></u><u></u></p>
<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">I am unfamiliar with Bridgeport’s climate, but as a general rule if I observed a significant amount of glazing in a space served by a direct evaporative cooler… I’d be extra cautious to ensure the HVAC designer is carefully considering condensation and potential for other humidity-driven issues along the way.  I’m most used to seeing them applied to well-ventilated and/or open-air spaces such as garages and gyms/hangars.</span><u></u><u></u></p>
<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">~Nick</span><u></u><u></u></p><p class="MsoNormal">
<span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><img src="cid:image001.jpg@01CC5CBB.C8A46B00" alt="cid:489575314@22072009-0ABB" width="119" border="0" height="37"></span><u></u><u></u></p>
<p class="MsoNormal"><b><span style="font-size: 11pt; color: rgb(45, 77, 94);"> </span></b><u></u><u></u></p><p class="MsoNormal"><b><span style="color: rgb(45, 77, 94);">NICK CATON, P.E.</span></b><u></u><u></u></p><p class="MsoNormal">
<span style="font-size: 7.5pt; color: rgb(204, 153, 0);">SENIOR ENGINEER</span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 7.5pt; color: rgb(204, 153, 0);"> </span><u></u><u></u></p><p class="MsoNormal">
<span style="font-size: 10pt; color: rgb(45, 77, 94);">Smith & Boucher Engineers</span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">25501 west valley parkway, suite 200</span><u></u><u></u></p>
<p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">olathe, ks 66061</span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">direct <a href="tel:913.344.0036" target="_blank">913.344.0036</a></span><u></u><u></u></p>
<p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">fax <a href="tel:913.345.0617" target="_blank">913.345.0617</a></span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><a href="http://www.smithboucher.com" title="blocked::www.smithboucher.com" target="_blank"><span style="font-size: 10pt;">www.smithboucher.com</span></a></span><u><span style="font-size: 10pt; color: blue;"> </span></u><u></u><u></u></p>
<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p><div style="border-width: 1pt medium medium; border-style: solid none none; padding: 3pt 0in 0in; border-color: -moz-use-text-color;">
<p class="MsoNormal"><b><span style="font-size: 10pt;">From:</span></b><span style="font-size: 10pt;"> <a href="mailto:equest-users-bounces@lists.onebuilding.org" target="_blank">equest-users-bounces@lists.onebuilding.org</a> [mailto:<a href="mailto:equest-users-bounces@lists.onebuilding.org" target="_blank">equest-users-bounces@lists.onebuilding.org</a>] <b>On Behalf Of </b>deepika khowal<br>
<b>Sent:</b> Tuesday, August 16, 2011 1:36 PM<br><b>To:</b> <a href="mailto:equest-users@lists.onebuilding.org" target="_blank">equest-users@lists.onebuilding.org</a><br><b>Subject:</b> [Equest-users] evaporative coolers in equest</span><u></u><u></u></p>
</div><div><div><p class="MsoNormal"> <u></u><u></u></p><p class="MsoNormal">Hello all<u></u><u></u></p><div><p class="MsoNormal">I am modeling a building in Bridgeport, CA which has evaporative coolers.<u></u><u></u></p>
</div><div><p class="MsoNormal">I dont see any benefits if I replace existing clear glass with low-e in cooling energy consumption.<u></u><u></u></p></div><div><p class="MsoNormal">Did anyone model evaporative coolers/swamp coolers before?<u></u><u></u></p>
</div><div><p class="MsoNormal">I want to know whether there is a way to show cooling benefit with such HVAC system.<u></u><u></u></p></div><div><p class="MsoNormal">Thanks<u></u><u></u></p></div><div><p class="MsoNormal">
Regards<u></u><u></u></p></div><div><p class="MsoNormal">Deepika<u></u><u></u></p></div></div></div></div></div></div><p class="MsoNormal"> <u></u><u></u></p></div><pre><u></u> <u></u></pre><pre><u></u> <u></u></pre><pre>
_______________________________________________<u></u><u></u></pre><pre>Equest-users mailing list<u></u><u></u></pre><pre><a href="http://lists.onebuilding.org/listinfo.cgi/equest-users-onebuilding.org" target="_blank">http://lists.onebuilding.org/listinfo.cgi/equest-users-onebuilding.org</a><u></u><u></u></pre>
<pre>To unsubscribe from this mailing list send  a blank message to <a href="mailto:EQUEST-USERS-UNSUBSCRIBE@ONEBUILDING.ORG" target="_blank">EQUEST-USERS-UNSUBSCRIBE@ONEBUILDING.ORG</a><u></u><u></u></pre><pre>  <u></u><u></u></pre>
<p class="MsoNormal"><u></u> <u></u></p></div></div><br><br>---------- Forwarded message ----------<br>From: deepika khowal <<a href="mailto:deepika.khowal@gmail.com">deepika.khowal@gmail.com</a>><br>To: Nick Caton <<a href="mailto:ncaton@smithboucher.com">ncaton@smithboucher.com</a>><br>
Date: Wed, 17 Aug 2011 10:00:03 -0700<br>Subject: Re: [Equest-users] evaporative coolers in equest<br>Thanks Patrick<div>I read the following link which talks abt sizing evaporative coolers</div><div><a href="http://www.consumerenergycenter.org/home/heating_cooling/evaporative.html" target="_blank">http://www.consumerenergycenter.org/home/heating_cooling/evaporative.html</a><br>

<br><div class="gmail_quote">On Wed, Aug 17, 2011 at 7:56 AM, Nick Caton <span dir="ltr"><<a href="mailto:ncaton@smithboucher.com" target="_blank">ncaton@smithboucher.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin: 0pt 0pt 0pt 0.8ex; border-left: 1px solid rgb(204, 204, 204); padding-left: 1ex;">

<div bgcolor="white" link="blue" vlink="purple" lang="EN-US"><div><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">Patrick, thanks for the heads up!<u></u><u></u></span></p><p class="MsoNormal">
<span style="font-size: 11pt; color: rgb(31, 73, 125);"><u></u> <u></u></span></p>
<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">My experience applying evap. coolers has been on a limited basis explicitly for space comfort, operated staged & cycled off via thermostat, so my brainstorming for Deepika was tailored to my past experience.  In those cases (auto garages), a mechanical ventilation system was provided as an entirely separate system, so the 62.1/IMC requirements for ventilation during occupancy were addressed elsewhere.<u></u><u></u></span></p>

<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><u></u> <u></u></span></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">If one is in fact using a swamp cooler functionally to supply required ventilation air, then I would agree it makes complete sense to operate continuously during occupied hours.  <u></u><u></u></span></p>

<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><u></u> <u></u></span></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">I recall evap. coolers being a breath of fresh air (har har) to design around as they do make you rethink how you use your psych charts =).  I’ll defer any specific swamp cooler application queries to the Arizona engineer below me though – we don’t use them quite so often locally, outside of the desert ;).<u></u><u></u></span></p>

<div><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><u></u> <u></u></span></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">~Nick<u></u><u></u></span></p><p class="MsoNormal">

<span style="font-size: 11pt; color: rgb(31, 73, 125);"><u></u> <u></u></span></p><div><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><img src="cid:image001.jpg@01CC5CBB.C8A46B00" alt="cid:489575314@22072009-0ABB" width="119" height="37"></span><b><span style="font-size: 11pt; color: rgb(45, 77, 94);"><u></u><u></u></span></b></p>

<p class="MsoNormal"><b><span style="font-size: 11pt; color: rgb(45, 77, 94);"><u></u> <u></u></span></b></p><p class="MsoNormal"><b><span style="color: rgb(45, 77, 94);">NICK CATON, P.E.</span></b><b><span style="color: rgb(45, 77, 94);"><u></u><u></u></span></b></p>

<p class="MsoNormal"><span style="font-size: 7.5pt; color: rgb(204, 153, 0);">SENIOR ENGINEER<u></u><u></u></span></p><p class="MsoNormal"><span style="font-size: 7.5pt; color: rgb(204, 153, 0);"><u></u> <u></u></span></p>
<p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">Smith & Boucher Engineers</span><span style="font-size: 7.5pt; color: rgb(204, 153, 0);"><u></u><u></u></span></p>
<p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">25501 west valley parkway, suite 200<u></u><u></u></span></p><p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">olathe, ks 66061<u></u><u></u></span></p>

<p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">direct <a href="tel:913.344.0036" value="+19133440036" target="_blank">913.344.0036</a><u></u><u></u></span></p><p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">fax <a href="tel:913.345.0617" value="+19133450617" target="_blank">913.345.0617</a><u></u><u></u></span></p>

<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><a href="http://www.smithboucher.com" title="blocked::www.smithboucher.com" target="_blank"><span style="font-size: 10pt;">www.smithboucher.com</span></a></span><u><span style="font-size: 10pt; color: blue;"> </span></u><span style="font-size: 11pt; color: rgb(31, 73, 125);"><u></u><u></u></span></p>

</div><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><u></u> <u></u></span></p></div><div><div style="border-width: 1pt medium medium; border-style: solid none none; border-color: rgb(181, 196, 223) -moz-use-text-color -moz-use-text-color; padding: 3pt 0in 0in;">
<p class="MsoNormal"><b><span style="font-size: 10pt; color: windowtext;">From:</span></b><span style="font-size: 10pt; color: windowtext;"> Patrick J. O'Leary, Jr. [mailto:<a href="mailto:poleary1969@gmail.com" target="_blank">poleary1969@gmail.com</a>] <br>

<b>Sent:</b> Tuesday, August 16, 2011 5:48 PM<br><b>To:</b> Nick Caton<br><b>Cc:</b> deepika khowal; <a href="mailto:equest-users@lists.onebuilding.org" target="_blank">equest-users@lists.onebuilding.org</a></span></p><div>

<div></div><div><br><b>Subject:</b> Re: [Equest-users] evaporative coolers in equest<u></u><u></u></div></div><p></p></div></div><div><div></div><div><p class="MsoNormal"><u></u> <u></u></p><p class="MsoNormal">
i would agree with nick on this except for part #3.  if you're using ashrae 62, or the 2000/2003/2006 imc (at least the way it is enforced in southern arizona), the evaporative cooler fan is required to run while the building is occupied so despite glazing upgrades you shouldn't be seeing any savings from the hvac system during occupied hours.  you would probably see some during night setback if the building there's some thermostat setting that will operate the evap coolers to remove air (and the associated heat build up) but i would not think it to be that significant of a savings compared to heat gain during occupied hours.<br>

<br>i would think, as nick mentions in point 5, that the ummet cooling hours might be a better measure of what you are looking for.  improved glazing should help reduce the rate of heat gain so the evap coolers should be able to meet whatever setpoint you are using with less unmet cooling hours.  in reality i would think it would be more obvious by an occupant working proximity to the windows - if they're currently affected by the solar heat gain.  i don't know your climate but in southern arizona you don't really want to be seated right next to a window with a direct sun exposure and insufficient airflow (evap) or mechanical cooling and poor windows.<br>

<br>On 8/16/11 2:22 PM, Nick Caton wrote: <u></u><u></u></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">I hope we’re at a simple vocabulary disconnect here...</span><u></u><u></u></p><p class="MsoNormal">

<span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p><p><span style="font-size: 11pt; color: rgb(31, 73, 125);">Upgrading the windows will reduce your solar cooling loads.</span><u></u><u></u></p>
<p><span style="font-size: 11pt; color: rgb(31, 73, 125);">Reducing your solar cooling loads will reduce the amount of heat to be removed from the building.</span><u></u><u></u></p>
<p><span style="font-size: 11pt; color: rgb(31, 73, 125);">Reducing the amount of heat to remove will reduce the required hours of operation of your HVAC system (in this case, evaporative coolers) to maintain comfort.</span><u></u><u></u></p>

<p><span style="font-size: 11pt; color: rgb(31, 73, 125);">Reducing the runtime of your evaporative coolers will result in reduced energy consumption.  Fan energies primarily, in the case of evaporative coolers.</span><u></u><u></u></p>

<p><span style="font-size: 11pt; color: rgb(31, 73, 125);">In the event the existing system is not of sufficient capacity to begin with, you may also/instead observe a reduction in unmet cooling hours.</span><u></u><u></u></p>
<p class="MsoNormal">
<span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">The reduction of solar loads with a glazing upgrade could be <i>negligible</i> for a variety of possible reasons, but it’s unlikely the net effect is absolutely zero.  </span><u></u><u></u></p>

<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">~Nick</span><u></u><u></u></p><p class="MsoNormal">
<span style="font-size: 11pt; color: rgb(31, 73, 125);"><img src="cid:image001.jpg@01CC5CBB.C8A46B00" alt="cid:489575314@22072009-0ABB" width="119" border="0" height="37"></span><u></u><u></u></p>
<p class="MsoNormal"><b><span style="font-size: 11pt; color: rgb(45, 77, 94);"> </span></b><u></u><u></u></p><p class="MsoNormal"><b><span style="color: rgb(45, 77, 94);">NICK CATON, P.E.</span></b><u></u><u></u></p><p class="MsoNormal">
<span style="font-size: 7.5pt; color: rgb(204, 153, 0);">SENIOR ENGINEER</span><u></u><u></u></p>
<p class="MsoNormal"><span style="font-size: 7.5pt; color: rgb(204, 153, 0);"> </span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">Smith & Boucher Engineers</span><u></u><u></u></p>
<p class="MsoNormal">
<span style="font-size: 10pt; color: rgb(45, 77, 94);">25501 west valley parkway, suite 200</span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">olathe, ks 66061</span><u></u><u></u></p>
<p class="MsoNormal">
<span style="font-size: 10pt; color: rgb(45, 77, 94);">direct <a href="tel:913.344.0036" value="+19133440036" target="_blank">913.344.0036</a></span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">fax <a href="tel:913.345.0617" value="+19133450617" target="_blank">913.345.0617</a></span><u></u><u></u></p>

<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><a href="http://www.smithboucher.com" title="blocked::www.smithboucher.com" target="_blank"><span style="font-size: 10pt;">www.smithboucher.com</span></a></span><u><span style="font-size: 10pt; color: blue;"> </span></u><u></u><u></u></p>

<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p><div style="border-width: 1pt medium medium; border-style: solid none none; padding: 3pt 0in 0in; border-color: -moz-use-text-color;">

<p class="MsoNormal"><b><span style="font-size: 10pt;">From:</span></b><span style="font-size: 10pt;"> deepika khowal [<a href="mailto:deepika.khowal@gmail.com" target="_blank">mailto:deepika.khowal@gmail.com</a>] <br><b>Sent:</b> Tuesday, August 16, 2011 3:11 PM<br>

<b>To:</b> Nick Caton<br><b>Cc:</b> <a href="mailto:equest-users@lists.onebuilding.org" target="_blank">equest-users@lists.onebuilding.org</a><br><b>Subject:</b> Re: [Equest-users] evaporative coolers in equest</span><u></u><u></u></p>

</div><p class="MsoNormal"> <u></u><u></u></p><p class="MsoNormal"> <u></u><u></u></p><div><p class="MsoNormal">This is an existing building with evaporative coolers.<u></u><u></u></p></div><div><p class="MsoNormal">the proposed design  to upgrade the windows and check the relative benefits.<u></u><u></u></p>

</div><div><p class="MsoNormal">I dont see much benefits in energy because  evaporative coolers are sized based on Cfm and not btus, the savings will be in cfms.<u></u><u></u></p></div><div><p class="MsoNormal">correct me if I am wrong.<u></u><u></u></p>

</div><div><p class="MsoNormal">is there any other way I can show the benefit in the proposed case if not HVAC benefits?<u></u><u></u></p></div><div><p class="MsoNormal" style="margin-bottom: 12pt;">Thanks<u></u><u></u></p>

<div><p class="MsoNormal">On Tue, Aug 16, 2011 at 1:00 PM, Nick Caton <<a href="mailto:ncaton@smithboucher.com" target="_blank">ncaton@smithboucher.com</a>> wrote:<u></u><u></u></p><div><div><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">Hi Deepika,</span><u></u><u></u></p>

<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">I’m not certain any increase/decrease in cooling loads (such as solar loads affected by changing glazing) should have any effect on the reported “space cooling energy” when you’re using evaporative coolers.  Direct evaporative (swamp) coolers of the simplest sort have only fan and pump energies to consider -  no refrigerant!  I would advise looking up the Detailed Simulation Reports Summary page 158/160 to review end use categories and what they cover. </span><u></u><u></u></p>

<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">I am unfamiliar with Bridgeport’s climate, but as a general rule if I observed a significant amount of glazing in a space served by a direct evaporative cooler… I’d be extra cautious to ensure the HVAC designer is carefully considering condensation and potential for other humidity-driven issues along the way.  I’m most used to seeing them applied to well-ventilated and/or open-air spaces such as garages and gyms/hangars.</span><u></u><u></u></p>

<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);">~Nick</span><u></u><u></u></p><p class="MsoNormal">
<span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p>
<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><img src="cid:image001.jpg@01CC5CBB.C8A46B00" alt="cid:489575314@22072009-0ABB" width="119" border="0" height="37"></span><u></u><u></u></p><p class="MsoNormal">

<b><span style="font-size: 11pt; color: rgb(45, 77, 94);"> </span></b><u></u><u></u></p><p class="MsoNormal"><b><span style="color: rgb(45, 77, 94);">NICK CATON, P.E.</span></b><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 7.5pt; color: rgb(204, 153, 0);">SENIOR ENGINEER</span><u></u><u></u></p>

<p class="MsoNormal"><span style="font-size: 7.5pt; color: rgb(204, 153, 0);"> </span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">Smith & Boucher Engineers</span><u></u><u></u></p>
<p class="MsoNormal">
<span style="font-size: 10pt; color: rgb(45, 77, 94);">25501 west valley parkway, suite 200</span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">olathe, ks 66061</span><u></u><u></u></p>
<p class="MsoNormal">
<span style="font-size: 10pt; color: rgb(45, 77, 94);">direct <a href="tel:913.344.0036" target="_blank">913.344.0036</a></span><u></u><u></u></p><p class="MsoNormal"><span style="font-size: 10pt; color: rgb(45, 77, 94);">fax <a href="tel:913.345.0617" target="_blank">913.345.0617</a></span><u></u><u></u></p>

<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"><a href="http://www.smithboucher.com" title="blocked::www.smithboucher.com" target="_blank"><span style="font-size: 10pt;">www.smithboucher.com</span></a></span><u><span style="font-size: 10pt; color: blue;"> </span></u><u></u><u></u></p>

<p class="MsoNormal"><span style="font-size: 11pt; color: rgb(31, 73, 125);"> </span><u></u><u></u></p><div style="border-width: 1pt medium medium; border-style: solid none none; padding: 3pt 0in 0in; border-color: -moz-use-text-color;">

<p class="MsoNormal"><b><span style="font-size: 10pt;">From:</span></b><span style="font-size: 10pt;"> <a href="mailto:equest-users-bounces@lists.onebuilding.org" target="_blank">equest-users-bounces@lists.onebuilding.org</a> [mailto:<a href="mailto:equest-users-bounces@lists.onebuilding.org" target="_blank">equest-users-bounces@lists.onebuilding.org</a>] <b>On Behalf Of </b>deepika khowal<br>

<b>Sent:</b> Tuesday, August 16, 2011 1:36 PM<br><b>To:</b> <a href="mailto:equest-users@lists.onebuilding.org" target="_blank">equest-users@lists.onebuilding.org</a><br><b>Subject:</b> [Equest-users] evaporative coolers in equest</span><u></u><u></u></p>

</div><div><div><p class="MsoNormal"> <u></u><u></u></p><p class="MsoNormal">Hello all<u></u><u></u></p><div><p class="MsoNormal">I am modeling a building in Bridgeport, CA which has evaporative coolers.<u></u><u></u></p>

</div><div><p class="MsoNormal">I dont see any benefits if I replace existing clear glass with low-e in cooling energy consumption.<u></u><u></u></p></div><div><p class="MsoNormal">Did anyone model evaporative coolers/swamp coolers before?<u></u><u></u></p>

</div><div><p class="MsoNormal">I want to know whether there is a way to show cooling benefit with such HVAC system.<u></u><u></u></p></div><div><p class="MsoNormal">Thanks<u></u><u></u></p></div><div><p class="MsoNormal">

Regards<u></u><u></u></p></div><div><p class="MsoNormal">Deepika<u></u><u></u></p></div></div></div></div></div></div><p class="MsoNormal"> <u></u><u></u></p></div><pre><u></u> <u></u></pre><pre><u></u> <u></u></pre><pre>
_______________________________________________<u></u><u></u></pre><pre>Equest-users mailing list<u></u><u></u></pre><pre><a href="http://lists.onebuilding.org/listinfo.cgi/equest-users-onebuilding.org" target="_blank">http://lists.onebuilding.org/listinfo.cgi/equest-users-onebuilding.org</a><u></u><u></u></pre>

<pre>To unsubscribe from this mailing list send  a blank message to <a href="mailto:EQUEST-USERS-UNSUBSCRIBE@ONEBUILDING.ORG" target="_blank">EQUEST-USERS-UNSUBSCRIBE@ONEBUILDING.ORG</a><u></u><u></u></pre><pre>  <u></u><u></u></pre>

<p class="MsoNormal"><u></u> <u></u></p></div></div></div></div></blockquote></div><br></div>
<br>_______________________________________________<br>
Equest-users mailing list<br>
<a href="mailto:Equest-users@lists.onebuilding.org">Equest-users@lists.onebuilding.org</a><br>
<a href="http://lists.onebuilding.org/listinfo.cgi/equest-users-onebuilding.org" target="_blank">http://lists.onebuilding.org/listinfo.cgi/equest-users-onebuilding.org</a><br>
<br></blockquote></div><br>