<br><div class="gmail_quote"><span dir="ltr"></span><br><blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">Also set your altitude to 0 or your cfms will be affected.<br>
<font color="#888888">Carol</font><div><div></div><div class="h5"><br><br><div class="gmail_quote">On Tue, Feb 9, 2010 at 12:51 PM, Thomas Serra <span dir="ltr"><<a href="mailto:tserra@emoenergy.com" target="_blank">tserra@emoenergy.com</a>></span> wrote:<br>

<blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">Check to see if you are using floor multipliers.  I have had issues where<br>
the floor multiplier doesn't apply properly to fixed capacities. If you have<br>
a 12000 btu fan coil but it is multiplied 3 times you may need to enter<br>
36,000 btu.<br>
<br>
Thomas Serra<br>
Project Manager<br>
EMO Energy Solutions, LLC<br>
3141 Fairview Park Drive, Suite 450<br>
Falls Church, VA 22042<br>
voice 703-205-0445 ex-113<br>
fax 703-205-0449<br>
<div><div></div><div><br>
-----Original Message-----<br>
From: <a href="mailto:omoltay@mimtarch.com" target="_blank">omoltay@mimtarch.com</a> [mailto:<a href="mailto:omoltay@mimtarch.com" target="_blank">omoltay@mimtarch.com</a>]<br>
Sent: Tuesday, February 09, 2010 3:21 PM<br>
To: <a href="mailto:equest-users@lists.onebuilding.org" target="_blank">equest-users@lists.onebuilding.org</a><br>
Subject: [Equest-users] Heating Capacities of FC Units<br>
<br>
Greetings once again,<br>
<br>
Trying to troubleshoot other problems, I was going over the SV-A report and<br>
to my suprise discovered that the heating capacities I have entered<br>
individually at each zone level for my FCU units have been modified by<br>
eQuest. They have all been more or less tripled.<br>
<br>
The cooling capacities, on the other hand, have stayed the same as I have<br>
entered them for each zonal unit.<br>
<br>
I thought eQuest would use the heating capacities when you enter them<br>
manually.<br>
<br>
Am I following the right procedure here? I have also entered the design<br>
flows for each zone taking the max. flow from FCU specifications. Outside<br>
air flows have been determined by ASHRAE 62.1 calculations and have been<br>
entered individually for each zone. Outside air is provided by SZRH system<br>
with a dummy zone.<br>
<br>
I am sending some screenshots to give you an idea.<br>
<br>
Thanks for any help,<br>
<br>
</div></div>_______________________________________________<br>
Equest-users mailing list<br>
<a href="http://lists.onebuilding.org/listinfo.cgi/equest-users-onebuilding.org" target="_blank">http://lists.onebuilding.org/listinfo.cgi/equest-users-onebuilding.org</a><br>
To unsubscribe from this mailing list send  a blank message to <a href="mailto:EQUEST-USERS-UNSUBSCRIBE@ONEBUILDING.ORG" target="_blank">EQUEST-USERS-UNSUBSCRIBE@ONEBUILDING.ORG</a><br>
</blockquote></div><br>
</div></div></blockquote></div><br>