<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META http-equiv=Content-Type content="text/html; charset=us-ascii">
<META content="MSHTML 6.00.2900.2963" name=GENERATOR>
<STYLE>@page Section1 {size: 8.5in 11.0in; margin: 1.0in 1.25in 1.0in 1.25in; }
P.MsoNormal {
FONT-SIZE: 11pt; MARGIN: 0in 0in 0pt; FONT-FAMILY: Arial
}
LI.MsoNormal {
FONT-SIZE: 11pt; MARGIN: 0in 0in 0pt; FONT-FAMILY: Arial
}
DIV.MsoNormal {
FONT-SIZE: 11pt; MARGIN: 0in 0in 0pt; FONT-FAMILY: Arial
}
A:link {
COLOR: blue; TEXT-DECORATION: underline
}
SPAN.MsoHyperlink {
COLOR: blue; TEXT-DECORATION: underline
}
A:visited {
COLOR: purple; TEXT-DECORATION: underline
}
SPAN.MsoHyperlinkFollowed {
COLOR: purple; TEXT-DECORATION: underline
}
SPAN.EmailStyle17 {
COLOR: windowtext; FONT-FAMILY: Arial
}
DIV.Section1 {
page: Section1
}
</STYLE>
</HEAD>
<BODY lang=EN-US vLink=purple link=blue>
<DIV dir=ltr align=left><SPAN class=849292018-12092006><FONT face=Arial
color=#0000ff size=2>Holly:</FONT></SPAN></DIV>
<DIV dir=ltr align=left><SPAN class=849292018-12092006><FONT face=Arial
color=#0000ff size=2></FONT></SPAN> </DIV>
<DIV dir=ltr align=left><SPAN class=849292018-12092006><FONT face=Arial
color=#0000ff size=2>Question #1 - I believe if you put the pump kW to 0.0, and
the piping losses to 0.0, you should lose nothing except what is called for by
the end use.</FONT></SPAN></DIV>
<DIV dir=ltr align=left><SPAN class=849292018-12092006><FONT face=Arial
color=#0000ff size=2></FONT></SPAN> </DIV>
<DIV dir=ltr align=left><SPAN class=849292018-12092006><FONT face=Arial
color=#0000ff size=2>Question #2 - Are you calling out furnace for your heat
source or heat pump? This would be found in the heating section of your
RTU parameters, not in the plant (Air Side, not Water
side).</FONT></SPAN></DIV><BR>
<DIV class=OutlookMessageHeader lang=en-us dir=ltr align=left>
<HR tabIndex=-1>
<FONT face=Tahoma size=2><B>From:</B> BLDG-SIM@GARD.COM
[mailto:BLDG-SIM@GARD.COM] <B>On Behalf Of </B>Holly Richardson<BR><B>Sent:</B>
Tuesday, September 12, 2006 10:26 AM<BR><B>To:</B>
BLDG-SIM@GARD.COM<BR><B>Subject:</B> [BLDG-SIM] <BR></FONT><BR></DIV>
<DIV></DIV>
<DIV class=Section1>
<P class=MsoNormal><FONT face=Arial size=2><SPAN
style="FONT-SIZE: 10pt"></SPAN></FONT> </P>
<P class=MsoNormal><FONT face=Arial size=2><SPAN style="FONT-SIZE: 10pt">Good
morning,</SPAN></FONT></P>
<P class=MsoNormal><FONT face=Arial size=2><SPAN
style="FONT-SIZE: 10pt"></SPAN></FONT> </P>
<P class=MsoNormal><FONT face=Arial size=2><SPAN
style="FONT-SIZE: 10pt">Question…The building I am modeling has one DWH (100
gallons) but is not on a loop, but rather the water is sent out when a sink or
dishwasher etc is calling for it. I placed a loop on my DWH in order too
get the system too supply water through out the building. The problem is
that my therms are way high and I believe it’s because of the hot water
loop. How can I fix this?</SPAN></FONT></P>
<P class=MsoNormal><FONT face=Arial size=2><SPAN
style="FONT-SIZE: 10pt"></SPAN></FONT> </P>
<P class=MsoNormal><FONT face=Arial size=2><SPAN style="FONT-SIZE: 10pt">Second
issue, I have a very basic DX cooling system in the building two 20 ton RTU, and
two natural gas forced air furnace. But when I look at the reports one of
them the SS-Q states that I have Heat Pump cooling and heating for my two
RTU’s. Am I reading this right, if so how do I remove the heat pump from
my model? I don’t now where or how it got added. </SPAN></FONT></P>
<P class=MsoNormal><FONT face=Arial size=2><SPAN
style="FONT-SIZE: 11pt"></SPAN></FONT> </P>
<P class=MsoNormal><FONT face=Arial size=2><SPAN
style="FONT-SIZE: 11pt">Thanks,</SPAN></FONT></P>
<P class=MsoNormal><FONT face=Arial size=2><SPAN
style="FONT-SIZE: 11pt">Holly</SPAN></FONT></P></DIV><PRE>
==================
You received this e-mail because you are subscribed
to the BLDG-SIM@GARD.COM mailing list. To unsubscribe
from this mailing list send a blank message to
BLDG-SIM-UNSUBSCRIBE@GARD.COM
</PRE><PRE>
===========================
You received this e-mail because you are subscribed
to the BLDG-SIM@GARD.COM mailing list. To unsubscribe
from this mailing list send a blank message to
BLDG-SIM-UNSUBSCRIBE@GARD.COM
</PRE></BODY></HTML>