[Equest-users] error message: "ShellWiz has no valid ZnGrpWizchildren." --- too many shells?

James Hansen JHANSEN at ghtltd.com
Tue Apr 13 12:43:48 PDT 2010


Open up your PD2 file and take a look around - the ZnGrpWiz command
usually follows the Dayshapes/Shapewiz commands for each shell, and
directly precedes definition of the custom zones for the shell.

 

Look thru each shell, and see if some have them and some don't...I don't
know why eQuest wouldn't automatically define this, but I've
successfully messed around with the PD2 file before without damaging
anything.  Make you can copy one of the ZnGrpWiz commands from one shell
to another and make sure to rename accordingly.

 

Shellwiz is a lot more important:  that's the "beginning" of the
definition for each shell.  Open up the PD2 file and see if there are
ANY shellwiz definitions, and report back...

 

GHT Limited
James Hansen, PE, LEED AP

Senior Associate

1010 N. Glebe Rd, Suite 200

Arlington, VA  22201-4749

703-338-5754 (Cell)

703-243-1200 (Office)

703-276-1376 (Fax)

www.ghtltd.com <http://www.ghtltd.com/> 

 

 

From: equest-users-bounces at lists.onebuilding.org
[mailto:equest-users-bounces at lists.onebuilding.org] On Behalf Of Carol
Gardner
Sent: Tuesday, April 13, 2010 3:29 PM
To: Richard Williams
Cc: equest-users at lists.onebuilding.org
Subject: Re: [Equest-users] error message: "ShellWiz has no valid
ZnGrpWizchildren." --- too many shells?

 

This sounds like an eQUEST developer question. Hopefully one of them
will be willing/able to take the time to answer it.

Carol

On Tue, Apr 13, 2010 at 12:09 PM, Richard Williams
<Richard.Williams at arup.com> wrote:

 

Dear all

 

I have been building a model with a large number of shells. I understand
that this is not ideal but I have many overhangs and setbacks.

 

Once I reach about 60-70 shells a get the following error messages:

 

"ShellWiz has no valid ZnGrpWiz children."

 

"Error: No ShellWiz components exist."

 

"Error creating BDL input file from wizard inputs!"

 

 

After these messages the model becomes unusable. Is this likely to be a
shell problem or perhaps something to do with the limitations of running
in wizard mode?

 

Any suggestions much appreciated.

 

Regards

 

Richard

____________________________________________________________
Electronic mail messages entering and leaving Arup  business
systems are scanned for acceptability of content and viruses


_______________________________________________
Equest-users mailing list
http://lists.onebuilding.org/listinfo.cgi/equest-users-onebuilding.org
To unsubscribe from this mailing list send  a blank message to
EQUEST-USERS-UNSUBSCRIBE at ONEBUILDING.ORG

 


The information contained in this communication is confidential, may be privileged, and is intended only for the use of the addressee.  It is the property of GHT Limited.  Unauthorized use, disclosure or copying of this communication or any part thereof is strictly prohibited and may be unlawful.  If you have received this communication in error, please notify me immediately by return e-mail or by e-mail to ght at ghtltd.com, and destroy this communication and all copies thereof, including all attachments.  Thank you.



-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.onebuilding.org/pipermail/equest-users-onebuilding.org/attachments/20100413/4e4d93ac/attachment.htm>


More information about the Equest-users mailing list